A Thomas flowmeter is a device in which heat is transferred at a measured rate from an electric coil to a flowing fluid, and the flow rate of the stream is calculated from the measured increase of the fluid temperature. Suppose a device of this sort is inserted in a stream of nitrogen, the current through the heating coil is adjusted until the wattmeter reads 1.00 kW, and the stream temperature goes from 25.0°C and 110 kPa before the heater to 28.6°C and 110 kPa after the heater. If the specific enthalpy of nitrogen is given by the formula a(wike) = 1.04(7(*c) - 250) what is the volumetric flow rate of the gas (L/s) upstream of the heater (i.e. at 25.0°C and 110 kPa)? L/s

A Thomas flowmeter is a device in which heat is transferred at a measured rate from an electric coil to a flowing fluid, and the flow rate of the stream is calculated from the measured increase of the fluid temperature. Suppose a device of this sort is inserted in a stream of nitrogen, the current through the heating coil is adjusted until the wattmeter reads 1.00 kW, and the stream temperature goes from 25.0°C and 110 kPa before the heater to 28.6°C and 110 kPa after the heater. If the specific enthalpy of nitrogen is given by the formula a(wike) = 1.04(7(*c) - 250) what is the volumetric flow rate of the gas (L/s) upstream of the heater (i.e. at 25.0°C and 110 kPa)? L/s

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A manometer with water as working fluid is connected to an air duct as shown in Figure 1.1. Flow Figure 1.1 Air flows through the pipe at a rate of 170 L/s. The pipe diameter is measured to be 20 cm at the entrance, which reduces to half with a smooth reducing section. The pressure difference between the two pipe sections is measured by a water manometer. Assume the system operates in the environment at a constant temperature 50°C. i) Determine the differential height of the water in the manometer. ii) List 3 assumptions you made in i)
A window air conditioning is operating with Refrigerant -R22. An engineer wants to collect data on the flow rate of the refrigerant. The refrigerant is passed through one inlet and one exit pipe (Flgure 2) of diameter 3 cm steadily at a pressure of 2.5 bar and temperature of 5 °C with a velocity of 3 m/s. Due to heat gain from its surrounding, the refrigerant leaves the pipe at a pressure of 2 bar and temperature of 25 °C. Figure 2. One inlet one exit pipe For the refrigerant, determine (a) The volume flowrate at the pipe inlet (b) The mass flow rate The velocity and volume flow rate at the pipe exit
Example A 5-hp fan is used in a large room to provide for air circulation. Assuming a well-insulated, sealed room determine the internal energy increase after 1h of operation.
Water at 20°C is flowing at steady-state through a piping system as shown. D2 The velocity distribution (in m/s ) in a pipe with D1 = 4 cm is given by 1/7 Vz = 3 R where R1 = D1/2 and r is the radial coordinate. If the volumetric flow rate of water through a pipe with D3 = 1 cm is 0.072 m³/min, calculate the volumetric flow rate of water (in cm³/s ) through a pipe with D2 = 2 cm
17.Find the heat flow during 5.0 h through a glass window of thickness 0.20 in. with an area of 40 ft² if the average outer surface temperature is 22°F and the average inner glass surface is 60°F. Show working equation with answer. Answer must be in BTU units.
Water is to be pumped from the bottom of a well 20 ft deep with a specific heat of 1 BTU/lbm F is pumped using a 1-hp jet pump. Heat is lost from the whole system at the constant rate of 500 BTU/min. What is the temperature (℉) of the water as it enters the storage tank assuming that the well water is at 35℉?
The figure below shows a mixing tank initially containing minitial = 2000 lb of liquid water. The tank is fitted with two inlet pipes, one delivering hot water at a mass flow rate of 0.8 lb/s and the other delivering cold water at a mass flow rate of 1.2 lb/s. Water exits through a single exit pipe at a mass flow rate of 2.5 lb/s. Hot water m₁ = 0.8 lb/s mfinal= i Determine the amount of water, in lb, in the tank after 0.5 hours. minitial lb 2 Cold water m₂ = 1.2 lb/s m3 = 2.5 lb/s
Refrigerant vapor rejects 70 kW of heat as it passes through an air-cooled condenser. The condenser has an air-side area of 210 m? and based on this area, has an overall heat transfer coefficient of 0.037 kW/m2.°C. Cooling air flows at a rate of 7.59 kg/s. If condensation of the refrigerant occurs at 55°C, what is the inlet temperature (in °C) of the air? Take the specific heat of air to be 1.02 kJ/kg.C. Round your answer to 2 decimal places.
A Liquid fluid with a density of 1,750 kg/m3 from an elevated 2m open reservoir (P1=0 bars) flows before the pump at 7.5 m/s. The liquid fluid is pumped at an unknown final velocity to a 75 meter elevated tank with a pressure reading of 7.75 Bars. assuming Friction losses is 757.75J and the actual WORK of the pump is 1,933,400J. Calculate the Final Velocity in m/s if the pump's efficiency is just 75% and for every 1,000 kg of fluid per hour.
Apply the first law of thermodynamics to flow system with two inlets and one outlet. Assume that heat is supplied to the system. Draw the neat sketch and lable inlet and outlet properties
A simple saturated refrigeration R-12 system operates at an evaporating temperature of -11 °C and a condensing temperature of 40 °C. Determine the volume flow in m3/sec rate for a refrigerant capacity of 1 kW.
A refrigerator removes heat from a freezing chamber at -15 °F and discharges it at 120 °F. What is its maximum coefficient of performance?