A three way intersection is in need of a traffic signal control system and you have been assigned the task to design and implement the system. Each direction has only one lane and one set of signal control lights (green, yellow and red). Your design should only allow one go or green light at a time. Further, all transitions from green to red should go through an intermediate 2-4 seconds yellow light. Complete the following steps for this design: ) Sketch of the intersection with variables identified and respective values defined

A three way intersection is in need of a traffic signal control system and you have been assigned the task to design and implement the system. Each direction has only one lane and one set of signal control lights (green, yellow and red). Your design should only allow one go or green light at a time. Further, all transitions from green to red should go through an intermediate 2-4 seconds yellow light. Complete the following steps for this design: ) Sketch of the intersection with variables identified and respective values defined

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter9: Unsymmetrical Faults

Section: Chapter Questions

Problem ACSQ

See similar textbooks

Similar questions

What is the countering sequence of the following circuit? Is it an asynchronous counter or a synchronous counter? Why?
Draw a block diagram for a closed loop traffic signal system which control automobile traffic at roadway intersections.
Estimate the length of conduit to perform the next bends. EMT will be bend using a hand bender. Provide your answer in inches (just the number) using up to 2 decimals. The picture shows two panels connected by a back-to-back 23.5" stubs EMT 3/4" 6.25 ft P
What does the DC NULL actually measures?
a. With aid of Figure QB1, analyse the principle of the three-zone directional distance protection. If a fault occurs in the F point, show the main protection relays and back-up relays respectively. X-1 X-2 zone-2 X-3 zone-1 X-4 zone-1 zone-3 2 Zone-2 F zone-2 zone-1 zone-3 zone-1 zone-2
What are the poles and zeros? Do they match up with the specifications?
29 seconds. Question Completion Status: A Moving to another question will save this response. uestion 8 Which of the following is the phase angle error (in degree) for a current transformer of class T category? 30 Moving to another question will save this response. DEL 0000
A real-life production facility scenario is given below. In a manufacturing facility, the pilot light comes “ON” when all of the following conditions are met: Both normally open circuit pressure switches must be closed. One of the two normally open limit switches must be closed An emergency stop or reset button to turn the Pilot lamp OFF if needed. Answer the following questions based on the above scenario. Identify and list the inputs and outputs used in this scenario. Draw a relay schematic for this scenario. Draw the ladder logic for the given scenario.
FIrst 3 question answers are give below answer the last two partsanswers: 1) relay at C (CT ratio) = 40 : 1 relay at B (CT ratio) = 60 : 1 relay at A (CT ratio) = 40 : 1 2) TMS/A = 0.711 3) top = 1.48 sec ( relay will operate as per the fault current level.) i) Design appropriate CT ratios for CTA, CTB, and CTC. (ii) Estimate time of Operation for all three relays for maximum value of fault current to maintain the selectivity. (iii) Determine TSM for relays at bus A and B for maximum fault current. (Use the standard formula for IDMT relays for these calculations.) (iv) Also use the standard curves for IDMT relays shown in Figure 2 to select TSM for relays at bus A and B for maximum fault current. Compare results obtained in (ii) and (iv). Verify the design to ensure that selectivity is maintained at minimum fault current for the fault in the same zone
Below figure shows a single line diagram of a portion of a radial distribution system. The PS of Relay 3 (R3) is 75% of CT Secondary and time setting multiplier is given 0.1. The CT ratio is given with each relay and fault current of each in bus bar is given in figure. PS for R1 and R2 is set at 100%. Determine the operating time of each relay. Consider 0.25 sec for time coordination time interval. R30.297 R2 = .475 R1 = .654 A B C ID 1000/1 R₁ 10,000 A 800/1 800/1 M R₂ R₁ 8000 A 6000 A 5000 A
Viva Questions:1. What is the difference between Shunt and Series Stub?2. The stub is used to produce pure resistance at the point of connection (True / False)3. The stub length can be varied from __________________.4. What are the design parameters for stubs?5. Can the stubs be made open or short?
15. What does a grounding symbol on a construction drawing convey?A. A single ground rodB. A grounding electrode systemC. A ground-fault current pathD. An equipment grounding conductor