A timber beam 6 in. by 10 in. is reinforced only at the bottom by a steel plate as shown in Fig. Determine the concentrated load that can be applied at the center of a simply supported span 18 ft long if n = 20, fs 18 ksi and fw ≤ 1200 psi. Show that the neutral axis is 7.1 in. below the top and that INA = 1160 in.4.

A timber beam 6 in. by 10 in. is reinforced only at the bottom by a steel plate as shown in Fig. Determine the concentrated load that can be applied at the center of a simply supported span 18 ft long if n = 20, fs 18 ksi and fw ≤ 1200 psi. Show that the neutral axis is 7.1 in. below the top and that INA = 1160 in.4.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A reinforced concrete beam has a width of 349mm and an effective depth of 493mm. f’c = 30MPa, fy = 419 MPa. Determine the balanced steel area in sq.mm.
A rectangular beam having a width of 250 mm has a total depth of 450 mm. It is reinforced at the bottom with a total steel area of 1875 sq.mm. placed at an effective depth of 375 mm. fc'=27.6MPa and fy=414.7 MPa. Determine the ratio of the distance from the neutral axis to the bottom of the beam over its effective depth.
A simply supported beam has a rectangular section of b 65 cm and h 45 cm. The beam extends over a span of 7 m and is subjected to ultimate load Wu (kN/m) over the entire span. Use fc'=28 MPa, fy = 420 MPa, and d = 38 cm to determine the maximum load Wu (kN/m) the beam can sustain assuming: %3D !! %3D a) The beam is made with plain concrete (no reinforcement) b) The beam is reinforced with As = 51 cm2.
A compo beam is fabricated by bolting two 2.6-in.-wide by 13-in.-deep timber planks to the sides of a 0.5-in. by 13-in. steel plate. The mod elasticity of the timber and the steel are 1970 ksi and 28800 ksi, respectively. The simply supported beam spans a distance of 17 ft and carries two concentrated loads P, which are applied as shown. Assume LAB=LCD= 4 ft, LBc = 9 ft, b = 2.6 in., d=13 in. and t = 0.5 in. (a) Determine the maximum bending stresses o,, o, produced in the timber planks and the steel plate if P = 3.7 kips. (b) Assume that the allowable bending stresses of the timber and the steel are 1080 psi and 23900 psi, respectively. Determine the largest acceptable magnitude for concentrated loads P. (You may neglect the weight of the beam in your calculations.) Answers: (a) o, = (b) P= i LAB i B b LBC F Cross section C ksi, o, = kips. LCD i D ksi. 0000000
A simply supported rectangular beam of length 6.45m has a width of 390.5mm and an effective depth of 610.5mm. The beam is to be reinforced using 12 ?? bars. The beam supports service dead loads of Wd = 13.5kN/m and WL = 35.5kN/m. f'c = 28Mpa and fy=420 MPa %3D Given: b= 390.5 mm d= 610.5mm L= 6.45 m Wd = 13.5 kN/m WL = 35.5 kN/m %3D 1. Calculate the ultimate moment capacity of the beam. 2. Calculate the height of the equivalent stress block. 3. Determine the number of bars required for this beam.
A wood beam with a cross section 4 x 6 in. is simply supported at A and B. 4 in. A B I -4.5 ft 6 in. 4 in. Section I-I The beam has a length of 9 ft and is subjected to point load P = 3.7 kips at mid-span. Calculate the state of stress at point C located 4 in. below the top of the beam and 4.5 ft to the right of support A. Neglect the weight of the beam. (Enter the normal and shear stresses in ksi. For the normal stresses, use the deformation sign convention. For the shear stress, use the sign convention for shear stresses. Consider only the in-plane stresses. Assume that the +x-axis is to the right along the length of the beam and the +y-axis is up along the page.) ................ 115.625 ksi Enter a number. ksi -102.78 X ksi
The beam is built up of 1/4-in vertical plywood strips separated by wood blocks. Determine the vertical shear force that causes maximum shear stress of 150psi. 1.0 in.. in. 1.0 in. MACARE SYSTY -/// 2 in. 12 in.
A doubly reinforced beam, which have a base of 310 mm, and an effective depth of 410 mm, is reinforced with steel area of 2263 sq. mm at the bottom, and 1232 sq. mm on the top. Take d' = 70 mm, fc' = 21 MPa, and fy = 345 MPa. c) What is the value of ρbalance?
For a circular simple beam below and given the weight of wood is 8 kN/m' and masonry to be 23.4kN/m3. Ew = 14000MPA. Allowable bending stress is 16MPA, Allowable shear is 0.75MPA and deflection is 1/360 of the span. a. Which of the following gives the uniform load if could support if bending stress controls. b. Which of the following gives the uniform load if could support if shearing stress controls. c. Which of the following gives the uniform load it could support if deflection controls. d. What is the safe load? C= 300mm W = WoL+ Wu 5m
MN/m². 1005. A timber beam 150 mm by 250 mm is reinforced at the bottom only by a steel plate, as shown in Fig. P-1005. Determine the concentrated load that can be applied at the center of a simply sup- . 6 m long if n = 20, 0, < 120 MPa, and ow < 8 MPa. Show ported span that the neutral axis is 170.2 mm below the top and that I = 416 X 10° mm*. Ans. P= 13.1 kN 150 mm- 250 mm 100 mm 10 mm
Consider the following beam section. It has a concrete compressive strength of 4,000 psi and Grade-60 bars. There are 4 #9 bars at the top and 9 #10 bars at the bottom. The area of a single #9 bar is 1.0 in.² and the area of a single #10 bar is 1.27 in.². The section is subjected to a positive moment with the top bars in compression. 5 in. 12 in. 10 in. O 20 in. оо 4 #9 bars O 8 in. 9 #10 bars 10 in. OF 2.75 in. 2.5 in. 2.5 in. 24 in. Does the beam satisfy the tension-controlled condition of ACI 318
A composite beam is fabricated by bolting two 2-in.-wide by 12-in.-deep timber planks to the sides of a 0.7-in. by 12-in. steel plate. The moduli of elasticity of the timber and the steel are 1790 ksi and 31800 ksi, respectively. The simply supported beam spans a distance of 21 ft and carries two concentrated loads P, which are applied as shown. Assume LAB = LCD = 7 ft, LBC = 7 ft, b = 2 in., d = 12 in. and t = 0.7 in.(a) Determine the maximum bending stresses σtσt, σsσs produced in the timber planks and the steel plate if P = 3.9 kips.(b) Assume that the allowable bending stresses of the timber and the steel are 1050 psi and 20800 psi, respectively. Determine the largest acceptable magnitude for concentrated loads P. (You may neglect the weight of the beam in your calculations.)