A total of 5 mL of blood samples were treated with trichloroacetic acid to precipitate proteins. After centrifugation, the resulting solution is adjusted to pH 3 and extracted with 5 ml. of methyl isobutyl ketone containing the ammonium pyrolydine dithiocarbamate (APDC) complexing compound. The extract was then measured its absorbance using an atomic absorption spectrometer (AAS) at 7. 283.3 nm with an absorbance of 0.502. A total of 5 mL of standard Pb solution with concentrations of 0.4 and 0.6 ppm was also given the same treatment and resulted in absorbance of 0.396 and 0.599 ppm. Determine the pb concentration in the sample in ppm

A total of 5 mL of blood samples were treated with trichloroacetic acid to precipitate proteins. After centrifugation, the resulting solution is adjusted to pH 3 and extracted with 5 ml. of methyl isobutyl ketone containing the ammonium pyrolydine dithiocarbamate (APDC) complexing compound. The extract was then measured its absorbance using an atomic absorption spectrometer (AAS) at 7. 283.3 nm with an absorbance of 0.502. A total of 5 mL of standard Pb solution with concentrations of 0.4 and 0.6 ppm was also given the same treatment and resulted in absorbance of 0.396 and 0.599 ppm. Determine the pb concentration in the sample in ppm

Chemistry

10th Edition

ISBN:9781305957404

Author:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Publisher:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Chapter1: Chemical Foundations

Section: Chapter Questions

Problem 1RQ: Define and explain the differences between the following terms. a. law and theory b. theory and...

See similar textbooks

Similar questions

43-45 An EDTA solution was prepared by dissolving approximately 4 g of the disodium salt in approximately 1 L of water. An average of 41.87 mL of this solution was required to titrate 50.00-mL aliquots of a standard that contained 0.6987 g of MgCO₃ (84.31 g/mol) per liter. Titration of a 25.00-mL sample of mineral water at pH 10 required 19.32 mL of the EDTA solution. A 50.00-mL aliquot of the mineral water was rendered strongly alkaline to precipitate the magnesium. Titration with a calcium-specific indicator required 30.27 mL of the EDTA solution. a) Calculate the molar concentration of the EDTA solution. b) Calculate concentration of CaCO₃ (100.09 g/mol) of the mineral water in ppm. c) Calculate concentration of MgCO₃ (84.31 g/mol) of the mineral water in ppm.
A standard solution contains 100 ppm of Fe, which was found to have an absorbance of 0.151 au at 508 nm after the addition of 1,10-phenanthroline, pH 4 buffer, and hydroxylamine. Then, a water sample treated similarly exhibited an absorbance of 0.109 au. Which of the following statements is true? (A) The Fe concentration of the water sample is higher than 100 ppm. B) The Fe concentration of the water sample is equal to 100 ppm. It is impossible to estimate the Fe content of the water sample from information presented. D) The Fe concentration of the water sample is lower than 100 ppm.
the total solubility of amoxicillin hydrate a weekly acid acidic drug with a PK of 7.11 in SO 00.0 1M in acquiesce buffered solution of a pH equaling 7.2 is
Substance P has an extinction coefficient of 72.22 mM-1cm-1 at 420nm. 2 μl of Substance P was added to 998 μl water and the Absorbance at 420nm was 0.820. Calculate the mM concentration of the original Substance P solution
A 0.500 g sample consisting of Na2CO3, NaHCO3, and inert materials was dissolved in sufficient water to give 250.0 mL of solution. A 25.00 mL aliquot of this solution was boiled with 50.00 mL of 0.01255 M HCI. Titration of the excess HCI to a phenolphthalein endpoint required 2.34 ml of 0.01063 M NaOH. The carbonate species in the second 25.00 mL aliquot was precipitated with an excess of BaCl2 and treated with 25.00 mL of the NaOH. Titration of the excess base required 7.63 mL of the standard acid. Calculate % Na,CO3 and NaHCO3 in the sample.
A 0.500 g sample consisting of NażCO3, NaHCO3, and inert materials was dissolved in sufficient water to give 250.0 mL of solution. A 25.00 mL aliquot of this solution was boiled with 50.00 ml of 0.01255 M HCI. Titration of the excess HCI to a phenolphthalein endpoint required 2.34 mL of 0.01063 M NaOH. The carbonate species in the second 25.00 mL aliquot was precipitated with an excess of BaC, and treated with 25.00 mL of the NaOH. Titration of the excess base reguired 7.63 mL of the standard acid. Calculate % NazCO3 and NaHCO3 in the sample.
Nitrate nitrogen in water is determined by reacting with phenoldisulfonic acid to give a yellow color with an absorption maximum at 410 nm. A 100-mL sample that has been stabilized by adding 0.8MLH,SO/L is treated with silver sulfate to precipitate chloride ion, which interferes. The precipitate is filtered and washed (washings added to filtered sample). The sample solution is adjusted to pH 7 with dilute NaOH and evaporated just to dryness. The residue is treated with 2.0mL phenol disulfonic acid solution and heated in a hot-water bath to aid dissolution. Twenty milliliters of distilled water and 6mL ammonia are added to develop the maximum color, and the clear solution is transferred to a 50-ml volumetric flask and diluted to volume with distilled water, A blank is prepared using the same volume of reagents, starting with the disulfonic acid step. A standard nitrate solution is prepared by dissolving 0.722 g anhydrous KNO3 and diluting to 1 L. A standard addition calibration is…
A 10.00mL sample of alcoholic ethyl acetate was diluted to 100.00 mL. 20.00 mL was aliquoted and mixed with 40.00 mL of 0.04672 M KOH. The resulting mixture was heated for 2 hours. CH3COOC2H5 + OH- → CH3COO- + C2H5OH After cooling, the excess OH was back titrated with 3.41 mL of 0.05042 M H2SO4. Answer the following: Calculate the number of moles of OH- that reacted with ethyl acetate. Calculate the number of moles of ethyl acetate in the 20.00 mL solution. What is the mass of ethyl acetate (FW=88.11 g/mol) in the original 10.00 mL sample?
A standard solution contains 100 ppm of Fe, which was found to have an absorbance of 0.151 au at 508 nm after the addition of 1,10-phenanthroline, pH 4 buffer, and hydroxylamine. Then, a water sample treated similarly exhibited an absorbance of 0.109 au. Which of the following statements is true? The Fe concentration of the water sample is higher than 100 ppm. It is impossible to estimate the Fe content of the water sample from information presented. The Fe concentration of the water sample is lower than 100 ppm. The Fe concentration of the water sample is equal to 100 ppm.
Chris wants to study an organometal complex that was synthesized as shown below. Cr3+ + 2salen) = Cr(salen),³ He first prepared the working standards by adding specific volumes of Cr3+ solution and added 5.00 ml of 0.500M salen and diluted the solutions to 32.0 ml. The absorbance of each standard was then measured at the Amax, 425 nm, using a UV-Vis spectrophotometer as shown in the table below. Table 1. Standardized solutions containing Cr(salen);". Concentration (M) Blank Absorbance 0.021 0.010 0.015 0.220 0.295 0.020 0.025 0.356 0.421 0.473 0.030 He then prepared an unknown solution by mixing 1.00-ml of 0.500 M Cr3+ with 2.00-ml of 0.500 M salen and diluting to 32.0 mL. The resulting mixture was found to have an absorbance of 0.285. A blank solution was run before analyzing the unknown and gave an absorbance of 0.015. A. Determine the best fit line (with r) of the calibration curve. B. Calculate the equilibrium concentration (mM) of Cr3+ in the sample. c. Calculate the equilibrium…
A 1.5000-g sample of cereals was analyzed for nitrogen using the Kjeldahl procedure. The receiving flask contained 69 mL of 0.02 M HCl. After the ammonia was collected, the solution was titrated with 0 M NaOH, requiring 11.72 mL to reach the methyl red endpoint. Calculate and percent protein in the sample (f=5.70). Ans. in 3 SFs
Treatment of ammonia with phenol in the presence of hypochlorite yields indophenol, a blue product that absrobs light at 625 nm, which can be used for the spectrophotometric determination of ammonia. ocr SHN + HO- indophenol anion To determine the ammonia concentration in a sample of lake water, three samples are prepared. In sample A, 10.0 mL of lake water is mixed with 5 mL of phenol solution and 2 mL of sodium hypochlorite solution, and diluted to 25.0 mL in a volumetric flask. In sample B, 10.0 mL of lake water is mixed with 5 mL of phenol solution, 2 mL of sodium hypochlorite solution, and 2.50 mL of a 5.50 x 104 M ammonia solution, and diluted to 25.0 mL. Sample C is a reagent blank. It contains 10.0 mL of distilled water, 5 mL of phenol solution, and 2 mL of sodium hypochlorite solution, diluted to 25.0 mL. The absorbance of the three samples is then measured at 625 nm in a 1.00 cm cuvette. The results are shown in the table. Absorbance Sample (625 nm) A 0.401 В 0.648 0.045 What…