A triangular distributed load of max intensity w =370 N/m acts on beam AB. The beam is supported by a pin at A and member CD, which is connected by pins at C and D respectively. Determine the reaction forces at A and C. Enter your answers in Cartesian components. Assume the masses of both beam AB and member CD are negligible. cc 30 BY NC SA 2016 Eric Davishahl Variable Value a b C 5.20 m 8.32 m 3.64 m The reaction at A is A = Values for dimensions on the figure are given in the following table. Note the figure may not be to scale. N. The reaction at C' is = D N. Y₁ -b- X î+ B î+ W'

A triangular distributed load of max intensity w =370 N/m acts on beam AB. The beam is supported by a pin at A and member CD, which is connected by pins at C and D respectively. Determine the reaction forces at A and C. Enter your answers in Cartesian components. Assume the masses of both beam AB and member CD are negligible. cc 30 BY NC SA 2016 Eric Davishahl Variable Value a b C 5.20 m 8.32 m 3.64 m The reaction at A is A = Values for dimensions on the figure are given in the following table. Note the figure may not be to scale. N. The reaction at C' is = D N. Y₁ -b- X î+ B î+ W'

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Qt The forces Fi and F2 at on a beacket as shown in the Figure bekow. Deternine the magnitade of the rescitant force F- 100 N
(b) (5 pt) Draw and properly label a free-body diagram of ring A of the structure shown. Include only relevant information; do not include any information that is not relevant to the free-body diagram. Note: Assume the ring at A is massless. 3 m 3 m wwww kac = 20 N/m 4 m KAB = 30 N/m www. KAD = 40 N/m B
(a) Based on the theory of deflection beam, state the boundary conditions of two beamsas shown in Figure Q2(a).
Solve for Ray, Rax and Rbx
Particle A lies on the x-y plane and is acted on by thethree forces shown. Find the resultant of the threeforces. Show FBD and complete solution
The rigid bar BDE is supported by two links AB and CD. Link AB is made of aluminum (E = 70 GPa) and has a cross sectional area of 500 mm^2. Link CD made of steel (E = 200 GPa) and has a cross sectional area of 600 mm^2. Determine the deflection at D in mm
A uniformly tapered aluminum-alloy tube AB of circular cross section and length L is shown in the figure. The outside diameters at the ends are da and dB = 2d4. A hollow section of length and constant thickness t = A is cast into the tube and extends from B halfway toward A. t constant de- 21 B dg (a) dg (b) (a) Find the angle of twist of the tube when it is subjected to torques T acting at the ends. Use numerical values as follows: da = 2.8 in., L = 43 in., G = 3.5 × 10° psi, and T = 38,000 in. – lb. Round your answer to two decimal places. ФА (b) Repeat (a) if the hollow section has constant diameter da (see figure part b). Round your answer to two decimal places.
3: Analysis the structure shown in figure, El is constant W=20 KN/m P-40 KN B4 4m
A triangular distributed load of max intensity w = 410 N/m acts on beam AB. The beam is supported by a pin at A and member CD, which is connected by pins at C and D respectively. Determine the reaction forces at A and C. Enter your answers in Cartesian components. Assume the masses of both beam AB and member CD are negligible. cc BY NC SA 2016 Eric Davishahl A D В C - Values for dimensions on the figure are given in the following table. Note the figure may not be to scale. Variable Value a 7.60 m b 11.4 m 4.56 m The reaction at A is A = ĵ N. The reaction at C is C ĵ N. =
State the determinacy of the beam shown. Answer is: Unstable. Show solution.
The beam shown below is suspended from two steelrods as shown and is initially horizontal. The midpointB of the beam is deflected 15 mm downward byforce Q. The steel used for the rods has properties E= 200 GPa and  = 275 MPa, determinea. the required maximum value of Q.b. the deformation of rod AD.c. the deformation of rod CE.
Example 2: Rigid rod supported by BDE, AB and CD. AB is made of aluminum (E = 70 GPa) and its area is 500 mm2, CD is made of steel (E = 200 GPa) and its area is 600mm2. Find a) the displacement at B b) the displacement at D c) the displacement at E due to the 30kN force acting at the end of E. Solution: We find the forces from the free body diagram of BDE.