A turbine engine air intake is at pressure and temperature of air drawn 99 kPa and 29 °C respectively. The maximum pressure and temperature during the cycle is 990 kPa and 888 °C respectively. The adaibatic index as 1.4. After claculations, the pressure ratio of the cycle is compressor exit temperature is K, turbine exit temperature is K, net specific work output from the gas turbine engine is in k thermal efficiency_ is % and work ratio of the cycle is to I decimal place.

A turbine engine air intake is at pressure and temperature of air drawn 99 kPa and 29 °C respectively. The maximum pressure and temperature during the cycle is 990 kPa and 888 °C respectively. The adaibatic index as 1.4. After claculations, the pressure ratio of the cycle is compressor exit temperature is K, turbine exit temperature is K, net specific work output from the gas turbine engine is in k thermal efficiency_ is % and work ratio of the cycle is to I decimal place.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

(17 blanks) Calculate the efficiency of the Carnot Engine for ideal gas. Consider the figure below for a complete cycle of Carnot engine, where the cycle goes from ad->ab->bc->cd Carnot cycle Он TH Tc - V 02016 Pearson Education, Inc. processes: processes and segment ab & cd are the Where segments ad & bc are the and the volumes involved are Va, Vb, Vc, Vd, and the two temperatures TC and
A turbine engine air intake is at pressure and temperature of air drawn 99 kPa and 29 0C respectively. The maximum pressure and temperature during the cycle is 990 kPa and 888 0C respectively. The adaibatic index as 1.4. After claculations, the pressure ratio of the cycle is , compressor exit temperature is K, turbine exit temperature is K, net specific work output from the gas turbine engine is in k, thermal efficiency is % and work ratio of the cycle is to I decimal place
Pls answer thank you! Steam enters the turbine at the rate of 2.5 kg/s with enthalpy of 3200 kj/kg and exhaust enthalpy of 1100 kj/kg . Steam is extracted from the turbine at the rate of 1 kg/s for heating purposes with enthalpy of 2750 kj/kg. What is the turbine work in KW.
Q2Air enters an insulated turbine at 50°C, and exits the turbine at - 30°C, 100 kPa.The isentropic turbine efficiency is 70% and T1=50C V=20L/s the inlet volumetric flow rate is 20 L/s. What is the turbine Air turbine inlet pressure and the turbine power output? T2=-30C.P2=100kpa
A turbine receives steam at 10 MPa, 6000C and exhaust it at 0.2 MPa. (a) for the ideal Rankine engine, determine the work, steam rate, thermal efficiency, and means effective pressure. (b) for the actual engine,the brake engine efficiency is 84%; the driven generator efficiency is 93% and the rated output of the generator is 30 MW. Estimate the enthalpy ang quality (or temperature) of the exhaust..Compute the combined work, combined heat rate, and the total throttle flow for the rated power. Don't answer the given problem, just give me the schematic diagram andT-S diagram of the given problem
thermodynamics A steam enters the system with enthalpy of 3300 KJ/kg at 200 m/sand leaves with enthalpy at 2700 KJ/kg at 80 m/s. Find the work outputof the turbine.
In a three-stage compressor, the pressure ratio in each stage is equal and its value is 1.3, the first inlet temperature to stage 300K, outlet pressure from first stage 1000mmHg, , Polytropic yield 0.92. m C1 C2 = C2s C3 C3s = 500 "It s Isentropic exponent=1.4, coefficient of heating heat under constant pressure= 1005 kgK' your mercury density= 13550 and gravitational acceleration= 9.81 m3 m3 a) Find the actual and isentropic temperature of the exit from the 1st stage. b) Find the actual and isentropic temperatures of the exit temperatures from the 2nd stage. c) Find the real and isentropic work consumed in Stage 2. d) Put the available data and your calculations in the compressor (h-s) diagram.
In a marine gas turbine unit, a high-pressure stage turbine drives the compressor and a low-pressure stage turbine drives the propeller through suitable gearing. The overall pressure ratio is 4/1 and the maximum temperature is 650 o the isentropic efficiencies of the compressor, H. P. turbine, L. P. turbine are 0.8, 0.83 and 0.85 respectively and the mechanical efficiency of both shafts is 98 %. Sketch the process on the T-s diagram i. Calculate the pressure between turbine stages when the air intake conditions are 1.01 bar and 25 oC. ii. Calculate also the thermal efficiency and the shaft power when the mass flow is 60 kg/s. NB: Neglect kinetic energy changes and the pressure loss in combustion.
Define and derive an expression for stage efficiency in case of a steam turbine.
occuring when a process with air, the entropy goes up by 0.60 kJ/kg·K. 11 is the pressure compression ratio. 300K is the initial temperature. What is the final temperature if it is a constant specific heat and if it is a variable specific heat? When Rair = 0.287 and cp = 1.005 kJ/kg·K.
A turbine engine air intake is at pressure and temperature of air drawn 99 kPa and 29 °C respectively. The maximum pressure and temperature during the cycle is 990 kPa and 888 °C respectively. If the e, the diagram Pthat shows the T-s-diagram is first process starts with isentropic compession, the next three processes should be and using the words listed below. The formula to calculate the work ratio is , pressure ratio is thermal efficiency is temperature at the compressor exit is temperature at the turbine exit is net specific work output from the gas turbine engine is Key words for processes: isentropic, isobaric, isothermal, isochoric, compression, expansion, heating and cooling.
Steam @ 500 C and 6 MPa expands in a turbine to 50 kPa and enthalpy of 2585, the turbine is not insulated and losses 120 to the surroundings which are at 19°C. What is the entropy generated (kJ/kg.K)? Select one: A. 0.9515 B. 0.7517 C. 1.0276 O D. 0.5406 X E. 0.8278