A typical capillary viscometer has a large-diameter reservoir and a long, small diameter, vertical tube. The sample is placed in the reservoir and the flow rate due to gravity is measured. The tube is 0.1 m long and has a 1 mm ID. The height of the fluid in the reservoir above the inlet to the tube is 0.02 m. The fluid being tested has a density of 1050 kg / m'. The flow rate is 10* m³ / s. What is the viscosity of the fluid? Typical capillary viscometer

A typical capillary viscometer has a large-diameter reservoir and a long, small diameter, vertical tube. The sample is placed in the reservoir and the flow rate due to gravity is measured. The tube is 0.1 m long and has a 1 mm ID. The height of the fluid in the reservoir above the inlet to the tube is 0.02 m. The fluid being tested has a density of 1050 kg / m'. The flow rate is 10* m³ / s. What is the viscosity of the fluid? Typical capillary viscometer

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

At a point in a pipe that lay flat ノ water in the pipe flows at a speed of 9.0 mls and has 6-40x 104 Pa a gaoge pressure is Find the gauge pressure at point 2 of pipe that lower than the first point 8.0 m and the cvoss - se ctional| area of the pipe is double of first point . Answer [1.52x105 Pa]
All |Q1: the pressure at point A is 172 fluids are at 20°C. The air pressure in the ра. closed chamber B is..[w(water)=9790 * [N/m?,w(SAE oil 30)=8720 N/m³ Air B SAE 30 oil Liquid, SG = 1.45| 5 cm 3 'cm 4 cm 6 cm Water A 8 cm 3 cm
Answer with True or False of the following question: (7M 1. Water flows steadily down a vertical pipe of constant cross section. Neglecting friction, according to Bernoulli's equation, velocity decreases with height. 2. A liquid in an open right circular cylinder is given rigid body rotation about the axis of the cylinder. The pressure distribution in any vertical plane is uniform. 3. A curved surface is submerged in a static liquid. The horizontal component of pressure force on it is equal to the pressure force on a vertical projection of the surface. 4. A U-tube manometer measures the difference in total energy between two points.
Example 3.8.In Example 3.7 we considered a vacuum system with zero leaks. No real vacuum systems aretotally leak-free; engineers work very hard to keep the leakage rate as low as possible. If thetank in Example 3.7 has a leak of 0.0001 lbm/min of air, what will the pressure-time plot looklike, and what will be the final pressure? ex: 3.7 is posted
|The System in figure below is at 2éc.If the ectmospnen'e pressure is l01-33kpa and the pressure at the bottem of the tan k is 260hPa What is the specific gracity of fluid X? T ake densities of oila89l kg /m³ mercuryz13,55 =13,550 kg/m3 and water = 99849 Im3 oil im Water FluidX Mercury 0 SM
In pressure and volume exerted in vacuum is directly proportional to - law, the O Flemings, Resistance Faradays, flow rate O Lenz, Current O Universal gas, Temperature
1- Consider single-phase fluid flow in a 1-D horizontal reservoir.The reservoir is discretized using four blocks in the x-direction. A well located in block 3 produces at a rate of 400STB/D. All grid blocks have Ax-250ft, w-900ft, h-100 ft, and kx-270md. The FVF and the viscosity of the flowing fluid are 1.0 RB/STB and 2cP, respectively. Identify the interior and boundary blocks in this reservoir. Write the flow equation for block 3 and give the physical meaning of each term in the equation.
The physical model of a pipe containing water with kinematic viscosity o = 0.804 × 10-6 ™* has been built in the scale of in a laboratory. i. Find the ratio of velocity of water in the main pipe with kinematic viscosity of 8 = 2.79 x 10-4 m? to the model. ii. Discuss the difference in the velocities of the model and main pipe.
The velocity distribution in a 0.02 m diameter horizontal pipe conveying carbon tetrachloride (specific gravity = 1.59, absolute viscosity = 9.6 x 10-6 Pa sec) is given by the parabolic equation: v(r)=0.01(0.12- r?), where v(r) is the velocity in (m/s) at a distance r in (m) from the pipe center. What is discharge? O a. 3.13 x-8 m3/s O b. None of the mentioned O c. 1.047 x 108 m3/sec O d. 4.97 x 109 m3/sec
Find Kinematic viscosities of air and water at T=406, p=170 kla -5 N.S -4 N.S Given Mar=1-91x10² M² = 6.53 × 16² 4532, C = 1972 1973 М :) m² water Water
n = Xe()r -------Equation 1 where X = 1.7419 and (E/R) = -0.018 are constants for a given fluid. You are required to carry out appropriate calculations on the effect of changes in temperature given in table A by using equation 1 for Ethanol on the viscosity of a fluid. Table A NO Temperature viscocity n T°C cP 10 3 20 30 5 40 6. 50 7 60 8 70 In addition to this, calculate other constraints such as the variety of shear stress (T) and force due to fluid viscosity, when the two layers of different compressible Newtonian fluids are contained between two flat plates separated by a distance of 0.05m and fluid moving with the velocity of 2m/s in the horizontal direction. Assume the shear area between the fluid layers is 0.5m². To do this you required to explain, with examples, the effects of temperature and shear forces on Newtonian and non-Newtonian fluid. Also, explain the operation and constraints of different viscometers that quantify viscosity in fluids. 2.
= Q2: A 1.78 L four-stroke petrol engine was tested at 2500 rpm. The developed brake power is 28 kW and the brake specific fuel consumption (bsfc) is 290 g/kW.hr. Air consumption is measured by means of air-box method with orifice diameter 3.2-cm and discharge coefficient 0.62 and the pressure difference across the orifice is 150-mm-water. The ambient pressure and the temperature in the test room is 101 kPa and 20 °C. Assume: CV 43.9 MJ/kg, PH20 -10³ kg/m³, comb = 98%, mech = 87%. (i) Determine the bmep, AFR, nv, power loss as friction, th.b. (ii) draw up the heat balance sheet on percentage basis, if the cooling water flow is 15 kg/min; rise in temperature of cooling water is 33 °C; exhaust gas temperature is 485 °C; Cpw is 4.2 kJ/kg.K and Cpesh is 1.25 kJ/kg.K.