A uniform bar of weight 50DN is held in horizontal posiion by3 vertical wires as shown. Diameter of steel wire is 0.625mmand radius of brass wire is 0.625mm.Wires are unstretchedbefore supparting the rigid par and are of equal iength.Egee = 200GPe Eprass = 80GPaRatio of stress in steel vwire to that of brass wireisBrassSleelBrassB.Uriform rigid bar600 N

Answered: Image /qna-images/answer/a8926cf7-d031-4a12-aeed-7d215e38ecd6.jpg

A uniform bar of weight 500N is held in horizontal position by 3 vertical wires as shown. Diameter of steel wire is 0.625mm and radius of brass wire is 0.625mm, Wires are unstretched before supporting the rigid bar and are of equal length. Esteel = 200GPa Eprass = 80GPA Ratio of stressin steel wire to that of brass wire is Brass Steel Brass B. Uriform rigid bar 500 N

A uniform bar of weight 500N is held in horizontal position by 3 vertical wires as shown. Diameter of steel wire is 0.625mm and radius of brass wire is 0.625mm, Wires are unstretched before supporting the rigid bar and are of equal length. Esteel = 200GPa Eprass = 80GPA Ratio of stressin steel wire to that of brass wire is Brass Steel Brass B. Uriform rigid bar 500 N

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Find stress of a aluminum cylinder of diameter 12.8mm and gauge length 50.8mm. The force applied is 47,500N.
Rod of diameter 20 mm is loaded with 5kN tension force. What is the magnitude of stress in the rod?
Problem 7 A 12-inches square steel bearing plate lies betw een an 8-inches diam eterw ooden postand a concete footing as show n in Fig.P-110.Determ ine the m axim um value of the bad P if the stress in w ood is lim ited to 1800 psiand that in conarete to 650 psi 8 in Bearing Plate 12 in 12 in Figure P-110
Bronze Figure (a) shows a rigid bar that is supported by a pin at A and two rods, one made of steel and the other of bronze. Neglecting the weight of the bar, compute the stress in cach rod caused by the 50-kN load, using the following data: Steel 2 m 1.0 m A Steel l06 m–10 m--0.8 m- Bronze Arca (mm?) 300 50 kN 600 (a) E (GPa) 200 83
A cast ALuminum cylinder o f a portable hdrauli c riveter is 208 mm in ddiameter The pressure. of The luid petermine Sui table thickness is 15,8 NImm2 by gauge. f the Cylinder wall assuming that the ield Point stress 442 N/mm2 And factor of safety of 6.2 Calculate. the tangential and radial stresses middle radius and at the inner outer surfa ce.
(5) A gas engine valve spring is loaded to 35kgf when the valve is closed & 52kgf hen the valve is open. The valve lift is 8mm. The outside diameter is to be from 38mm~45mm, & the permissible stress is 413N/mm2 . Determine: (a) the wire & outside diameter; (b) the number of effective coils; (c) the free length when it is squared & ground.
A steam boiler is to have a 300-mm-diameter hand hole placed on one end. Ifthe maximum internal pressure is to be 1,3 MPa, how many 15-mm bolts willbe required to keep the cover plate in position? The root diameter of a 15-mmbolt is 12 mm. The allowable tensile stress in the bolts is 100 MPa and theinitial stress in the bolts when they are tightened is 60 MPa.
A steam boiler is to have a 300 mm diameter hand placed hole on one end. If themaximum internal pressure is 1.3 MPa, how many 15 mm holes will be required to keepthe cover plate in position? The root diameter of a 15 mm bolt is 12 mm. The allowabletensile stress in the bolts is 100 MPa and the initial stress in the bolts when they aretightened is 600 MPa.
Answer the ff correctly. The rectangular bar shown is connected to a support bracket with a 24 mm diameter pin. The width of the rectangular bar is 70 mm and its thickness is 15 mm. The bearing stress in the bar cannot exceed 120 MPa. Determine the maximum value of Pmax that can be supported based solely on consideration of the bearing stress in the bar. Note: This question is not asking about any stresses in the support bracket...just bearing stress in the rectangular bar.
A mild steel rod of 25 mm diameter and 400 m long is encased centrally inside a hollow coppertube of external diameter 35 mm and inside diameter 30 mm. The ends of the rod and tube arerigidly attached, and the composite bar is subjected to an axial pull of 40 kN. If E for steel andcooper is 200 GN/m2 and 100 GN/m2 respectively, find the stress developed in the rod and thetube. Find also the extension of the rod.
The thick walled cylinder of a hydraulic system is acted by a hydraulic pressure of 370 psi while themaximum load of the piston is 5500 lbs. If the allowable tensile stress is 2 ksi, find the required wallthickness of the cylinder.
(4) The plunger of an oil pump is held against the operating cam by a spring made of No.10 W&M gage steel wire coiled with an outside diameter of 7%-in. There are five active coils. The open length is 1.1875in. What are the length & stress when a load of 30lb is applied.