A voltage divider like that in the figure is to be designed sothat vo= kv, at no load (R₁ = ∞) and vo = av, atfull load (R₁ = Ro). Note that by definition a < k < 1. (Figure 1)FigureVsR₁R₂Vo1 of 1RLSpecify the numerical values of R₁ and R₂ if k = 0.85, a = 0.80, and Ro = 34 kN.Enter your answers numerically separated by a comma.R₁, R2 = 2.50,14.2 kSubmitPrevious AnswersCorrectPart DIf vs = 80 V, specify the maximum power that will be dissipated in R₁ and R₂.Enter your answers numerically separated by a comma.VE ΑΣΦPR₁ PR₂ = 52.323,5441.916↓↑vecSubmit Previous Answers Request AnswerX Incorrect; Try Again; 2 attempts remaining?mW

Introduction Power dissipation Power dissipation is a process in electrical engineering circuits…

A voltage divider like that in the figure is to be designed so that vo kv, at no load (RL = ∞o) and vo= av, at full load (RL = Ro). Note that by definition a R₁ Specify the numerical values of R₁ and R₂ if k = 0.85, a = 0.80, and Ro = 34 kn. Enter your answers numerically separated by a comma. R₁, R₂2.50,14.2 k Submit Previous Answers ✓ Correct Part D If us = 80 V, specify the maximum power that will be dissipated in R₁ and R2. Enter your answers numerically separated by a comma. 15. ΑΣΦ PR₁ PR₂ 52.323,5441.916 Submit vec Previous Answers Request Answer X Incorrect; Try Again; 2 attempts remaining www. ? mW

A voltage divider like that in the figure is to be designed so that vo kv, at no load (RL = ∞o) and vo= av, at full load (RL = Ro). Note that by definition a R₁ Specify the numerical values of R₁ and R₂ if k = 0.85, a = 0.80, and Ro = 34 kn. Enter your answers numerically separated by a comma. R₁, R₂2.50,14.2 k Submit Previous Answers ✓ Correct Part D If us = 80 V, specify the maximum power that will be dissipated in R₁ and R2. Enter your answers numerically separated by a comma. 15. ΑΣΦ PR₁ PR₂ 52.323,5441.916 Submit vec Previous Answers Request Answer X Incorrect; Try Again; 2 attempts remaining www. ? mW

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.20P: A circuit consists of two impedances, Z1=2030 and Z2=2560, in parallel, supplied by a source voltage...

See similar textbooks

Similar questions

A 22-k resistor and a 0.02-F capacitor are connected in series to a 5-V source. How long will it take the capacitor to charge to 3.4 V Select one: a. 0.501 ms b. 0.66 ms c. 0.44 ms d. 0.70 ms
Please simulate the given figure at multisim.com Will get a like.
. For the circuit shown in figure. For the circuit shown 16ke Rc 18V in Figure. If VeE =-|4V -14v RB Vec=18 V, VeE = 8 V, I8= 8MA, B= 100 %3D The value of RB is Kohm. . * ... ... ......
A resistor of 20ohms and a capacitance of unknown value when connected. In in parallel across a 100V, 50Hz supply take a current of 6A. The combination is now connected across a 100V supply of unknown frequency and the current falls to 5.5A . What is the frequency?
for the R-th part. isn't R3 and R5 in series not parrallel? If not, explain why. If so, fix the solution. THank you.
A resistor of 20 Ohms and a capacitance of unknown value when connected in in parallel across a 100V, 50Hz supply, take a current of 6A. The combination is now connected across a 100v supply of unknown frequency and the current falls to 5.5A. What is the frequency?
A 6-ohm resistor is connected in parallel with a 300 uF capacitor and the circuit is supplied by a 10A 60Hz current source. Find the instantaneous current through the resistor and the capacitor.
Attenuators with Capacitances Construct the circuit in Figure. Use R1 = 1kohm, C1-39nF. R2=3.9kohm. Vi C1 R1 HH R2 Vo What is the effect of the capacitor C1 in the circuit? You may use equations to help explain your answer.
Using the series circuit in Figure 3 consisting of a voltage source V, the resistor R and the fully uncharged capacitor C, how to find the value of the capacitance C considering as known data the time constant of the circuit T and the value of the resistor R? V ww R
A series R–L–C circuit comprises a 5µF capacitor, a 4ohm resistor and a variable inductance L. The supply voltage is 10∠0◦ V at a frequency of 159.1 Hz. The inductance is adjusted until the p.d. across the 4 ohm resistanceis a maximum. Determine for this condition (a) the value of inductance, (b) the p.d. across each component and (c) the Q-factor of the circuit.
The high voltage arm of an RC divider has 10x100 ohms resistors with a 15-pF capacitor to the ground from each of the junction points. The ow voltage arm resistance is 10 ohms. Determine the capacitance need the LV arm for correct compensation.
30 Ω resistor in the circuit in the figure.and 1.273 mH coil to the source with a frequency of 5 kHzconnected to the sinusoidal source. ResistanceSince VR=6 V voltage drops on itthe voltage falling on the inductance, the sourceCalculate the voltage, active and reactive powers.