A voltage transformer in Figure 8 has 1,500 turns of wire on its primary winding and 500 turns of wire for its secondary winding. What will be the turns ratio, a of the transformer. If 240 volts is applied to the primary winding, what will be the resulting secondary voltage. And if a 400 resistor is connected to the secondary winding, what are the values of current Is and Ip.

A voltage transformer in Figure 8 has 1,500 turns of wire on its primary winding and 500 turns of wire for its secondary winding. What will be the turns ratio, a of the transformer. If 240 volts is applied to the primary winding, what will be the resulting secondary voltage. And if a 400 resistor is connected to the secondary winding, what are the values of current Is and Ip.

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter7: Parallel Circuits

Section: Chapter Questions

Problem 4PP: Using the rules for parallel circuits and Ohmslaw, solve for the missing values....

See similar textbooks

Similar questions

1a) As depicted in the figure, input voltage is 120 Volts (RMS) and diode drops are 0.7 Volts. Design this circuit with given two outputs and calculate turns ratio of transformer. i) 10 V ii) 100 V
An AC source provides peak output Vi and peak current ii when connected to the coil primary of a transformer. The transformer has Np turns in the primary coil and Ns turns in the secondary coil. A resistance circuit R is connected to the transformer, see figure below. What is the equivalent resistance of the circuit?
Q5. For the following center tapped transformer, show the waveform across each half of the secondary winding and across R1, when a 100 V peak sine wave is applied to the primarywinding. What is the PIV rating must the diode have? (Use constant voltage drop model for the Silicon diode) D IN4001 R1 V out 10 kN D2 IN4001 allle
a) The transformer has a turns ratio of 9.45, what is the dc load voltage considering the ripple voltage? b) The transformer has a turns ratio of 9.45, what is the dc load voltage without considering the ripple voltage?in 2 decimal places.
please write introduction about AC Circuits and Parallel Circuits
Determine the peak-to-peak ripple and dc output voltages. The transformer has a 36 Vrms secondary voltage rating, and the line voltage has a frequency of 60 Hz. Use germanium diodes.
An RLC series circuit connected to a 110 – volt and 50 – cycle AC source, contains the following series resistances and reactances: R1 = 10 ohm, R2 = 15, R3 = 5 ohms, XL1 = 20 ohms, XL2 = 25 ohms, XC = 40 ohms. Find the following: a.) EQUIVALENT REACTANCE b.) TOTAL IMPEDANCE c.) VOLTAGE DROP ACROSS THE CAPACITOR d.) TOTAL INDUCTANCE IN MILLIHENRY e.) TOTAL CURRENT f.) REACTIVE POWER g.) REAL POWER DRAW THE PHASOR DIAGRAM IF POSSIBLE AND ROUND OFF TO FOUR DECIMAL PLACES
A 120 – volt AC voltage is applied across a 20 – ohm resistive load. Find values of current, max voltage, peak–to–peak voltage, average voltage, maximum current, peak–to–peak current, average current, and power. draw the circuit diagram
If the output voltage across the transformer secondary coil is Vm AC volt. a- Give a circuit to covert the Vm AC volt. to double Vm DC volt. b- Determine the voltage across each capacitor during the positive half cycle of the AC signal. c- Determine the voltage across each capacitor during the negative half cycle of the AC signal.
electrical engineering what is current transformers advantage?
AC power of 100 volts and 1 ampere enters a transformer with 2 coils and exits the transformer with 20 coils. What is the exiting voltage and current? a.) 1000v/0.1amp b.) 0.1v/1000amp c.)1000v/1amp d.) 2v/20amp e.) No change
If we increase the load than core loss and copper loss will... Decrease Increase Remain same