A W8x35 steel column has an unsupported height of 8 m. Using A36 steel with F = 248 MPa and E = 200,000 MPa. Compute the allowable axial load Pa (ASD) and ultimate axial load Pu (LRFD) that the column could carry: a. if both ends are fixed. b. if both ends are pinned. c. if one end is fixed and the other end is pinned. Properties of W8x35: A = 6,645.15 mm2? k = 52.45 × 10º mm x = 88.9 mm ly = 17.69 × 10 mm4 Ty = 51.56 mm

A W8x35 steel column has an unsupported height of 8 m. Using A36 steel with F = 248 MPa and E = 200,000 MPa. Compute the allowable axial load Pa (ASD) and ultimate axial load Pu (LRFD) that the column could carry: a. if both ends are fixed. b. if both ends are pinned. c. if one end is fixed and the other end is pinned. Properties of W8x35: A = 6,645.15 mm2? k = 52.45 × 10º mm x = 88.9 mm ly = 17.69 × 10 mm4 Ty = 51.56 mm

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter5: Beams

Section: Chapter Questions

Problem 5.5.12P

See similar textbooks

Similar questions

steel Design Civil Engineering Please show solutions: AW 310 x 118 section with a length of 8.0 m is used as a column. Determine the safe axial load the column can carry using AISC specifications with Fy = 345 MPa when: Properties of W 310 x 118 A = 15000 mm² rx = 136 mm ry = 77.6 mm A. column ends are fixed B. one end of the column is fixed; the other free Use LRFD Answers: A.] For Ag = 248.06X15000 100 3720,9kw $en=0.90x3720.9 = 3348.21 kW B.JPn= For Ag =40.72 x 15 000 LOW Pr= 0.90x610,81 = 549.729 KN
Q2) The members of the truss structure shown below is plain concrete. The compressive strength of the concrete is 25 MPa. Compute the maximum load P that can be carried by the structure. (Cross section of each member of the truss is 200 x 200 mm and don't use material factors and do not consider slenderness) Comment on your results briefly. P A& 2m SC 2 m 1380 2m D
A simply supported beam is subjected to a uniform service dead load of 15kN/m(including the weight of the beam), a uniform service live load of 30kN/m. the beam is 12 meters long and is laterally supported at the midspan, and A572 Gr.50 steel is used. Is W30x108 adequate? Assume Cb=1 by 4 d fore k h h Z S Ly 267 TH mm 19.3 757 13.8 min m 35.8 685.4 54.6 737.7 5670 x10^3 4900 x103 mm 60.8 x10 6 mm 2080 x10 3 8300 x10^9 mm www
The beam shown in the figure has continuous lateral support of bothflanges. The uniform load is a service load consisting of 50% deadload and 50% live load. The dead load includes the weight of thebeam. If A992 steel is used, is a W16 × 31 adequate?a. Use LRFD.b. Use ASD.
A W21 x 57 of A992Gr50 steel column having length of 6 m and is fixed at both ends. (Gr50 steel = 50 ksi = 345 MPa = Fy) is used to carry a load of 900 kN dead load and 400 kN live load. Note: Use NSCP 2015 Properties of W21 x 57 A 10800 mm d = 536 mm bf = 167 mm tr = 16.5 mm tw 10.3 mm Kdes rx = 212 mm Ry = 34.3 mm = 29.2 mm a. Calculate the critical slenderness ratio of the W section if the column is braced at midpoint of the weak axis b. Calculate the compressive capacity of built-up section using ASD and LRFD c. Calculate the demand-capacity factor, Is the section adequate?
The beam shown is simply supported and has lateral support only at its ends. The only service dead load is the weight of the beam. Determine whether it is satisfactory for the load shown. A992 steel (E= 345 MPa and F= 450 MPa) is used, and the 30 KN/m is a service live load. Use LRFD 30 KN/m WiL = 30 KN/m W16x 40 -Centroid W16 x 40 3m
Rigid member BED is supported using steel rods AB, CD, and EF as shown below. E-200 GPa for steel. If a force P is applied at E, determine: a) The stress in each rod b) The length of each rod after applying the force LI (mm) LI (mm) P (kN) AAB (mm2) ACD (mm?) AEF (mm) 395 350 20 250 250 450 L1 L2 Note: BE ED P.
A W21 3 68 of A992 steel is used as a simply supported beam with a span length of 50 feet. The only load in addition to the beam weight is a uniform live load. If lateral support is provided at 10-foot intervals, what is the maximum service live load, in kipsyft, that can be supported? a. Use LRFD. b. Use ASD.
Write your answer (3 decimal places) on the text box provided in each number and use three (3) decimal places in all the computations. The compression member, 8 m long. loaded with service loads has braced in the weak direction as shown in the figure. A992 steel (EF 350 MPa and F.= 450 MPa) is used. Local stability is not a requirement. Use ASD.\ POL= PLL-160OKN 800 KN 4.30m W-shape 3.70m POL 800 KN PLL=1600KN 1. If a W16 x 77 is used, what is the value of the slenderness ratio to be used in this compression member?0 2. Compute the allowable compressive strength of a W 16 x 77 if used for this column in KN.O 3. Select the lightest W shape for the compression member.0 4. What is the value of the slenderness ratio used for the lightest W shape?0
A column is built up from four (4)- 125 x 125 x 18 angle shapes as shown. The plates are not continuous but are spaced at intervals along the column length and function to maintain the separation of the angles. They do not contribute to the cross-sectional properties. The effective length is 4 m. Compute the allowable design compressive strength based on flexural buckling. E= 250 MPa. Use ASD. k 375 mm 125mm, HPlate 125mm 4 - 4 125 × 125× l8 section 下好业

Use A992 steel and select a W14 shape for an axially loaded column to meet the following specifications: The length is 22 feet, both ends are pinned, and there is bracing in the weak direction at a point 10 feet from the top. The service dead load is 142 kips, and the service live load is 356 kips. a. Use LRFD. b. Use ASD.
4. 2L100x100x8 are welded together to form a box section as shown. It is used as a compression member to support a vertical load, P. The column is hinged on its top and fixed at the bottom (k = 0.70). Determine the largest allowable P that the column can carry if it has an unsupported length of 4m. Use A36 steel (Fy = 248 MPa) Properties of an L100x100x8: Area = 1551 mm² Moment of Inertia, Ix = ly 1448 x 10³ mm4 Centroid, x = y = 27.37 mm Ans. 343.02 KN 8 100 + 100 CIVIL ENGINEERING-SYEEL DESSION