A well-insulated 3-m 3 4-m 3 6-m room initially at 7°C is heated by the radiator of a steam- heating system. The radiator has a volume of 15 L and is filled with superheated vapor at 200 kPa and 200°C. At this moment both the inlet and the exit valves to the radiator are closed. A 120-W fan is used to distribute the air in the room. The pressure of the steam is observed to drop to 100 kPa after 45 min as a result of heat transfer to the room. Assuming constant specific heats for air at room temperature, determine the average temperature of air in 45 min. Assume the air pressure in the room remains constant at 100 kPa. Fan 7°C 3 mx 4 mx 6 m Steam radiator

A well-insulated 3-m 3 4-m 3 6-m room initially at 7°C is heated by the radiator of a steam- heating system. The radiator has a volume of 15 L and is filled with superheated vapor at 200 kPa and 200°C. At this moment both the inlet and the exit valves to the radiator are closed. A 120-W fan is used to distribute the air in the room. The pressure of the steam is observed to drop to 100 kPa after 45 min as a result of heat transfer to the room. Assuming constant specific heats for air at room temperature, determine the average temperature of air in 45 min. Assume the air pressure in the room remains constant at 100 kPa. Fan 7°C 3 mx 4 mx 6 m Steam radiator

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Inside a piston-cylinder device there is 5 kg of a moist water vapor at 125 kPa. At the beginning there are 2 kg of water in the liquid phase, and the rest is in the vapor phase. Then, heat is transferred to the water; the plunger, which rests on a set of stops, begins to rise when the pressure inside reaches 300 kPa. TheHeat transfer continues until the total volume increases by 20 percent.Determine:a) the initial and final temperatures,b) the mass of the liquid water when the plunger starts to rise andc) the work carried out during this process. Also plot the process on a P-v diagram.
A piston-cylinder device contains 0.91 kg of refrigerant-134a at –10°C. The piston that is free to move has a mass of 12 kg and a diameter of 25 cm. The local atmospheric pressure is 88 kPa. Now, heat is transferred to refrigerant-134a until the temperature is 15°C. Use data from the tables. R-134a -10°C Problem 03.030.b - Change of volume of cylinder with refrigerant Determine the change in the volume of the cylinder of the refrigerant-134a if the specific volume and enthalpy of R-134a at the initial state of 90.4 kPa and -10°C and at the final state of 90.4 kPa and 15°C are as follows: 1= 0.2418 m3/kg, m = 247.77 kJ/kg v2 = 0.2670 m3/kg, and h2 = 268.18 kJ/kg The change in the volume of the cylinder is ]m³.
Initially, 200 L of saturated vapor refrigerant-134a in a piston. The piston is free to move, and its mass is such that it maintains a pressure of 900 kPa on the refrigerant. The refrigerant is now heated until its temperature rises to 60°C. The work done during this process is Select one: 73.55 kJ 37.55 kJ 27.49 kJ O 72.49 kJ
A soup is set to boil. When the soup reaches 170°F, remove it from the heat and set it on the kitchen counter. The air in the kitchen is 80°F, and the soup in the bowl is 120°F after two minutes. After removing the soup from the heat, how long will it be 90°F?
(i) A can of soft drink at room temperature is put into the refrigerator so that it will cool. Would you model the can of soft drink as a closed system or as an open system? (ii) A candle is burning in a well-insulated room. Taking the room (the air plus the candle) as the system, determine if there is any heat transfer during the burning process. Explain how?
In a piston cylinder Assembly, R-134a refrigerant is available in 240 kPa and 40°C at a volume of 0.1 m3. The pressure created by the piston, which is held constant with the pin, and the masses and atmospheric pressure on it, is 280 KPA. It is heated in constant volume until the pressure inside the cylinder is increased to 280 KPA. And then the heat is drawn by a slow process with the cooling process by pulling the pin. If the temperature reached after this process is 50°C, find heat and work interactions during these two processes.
1. A scuba tank contains 1.5 kg of air. The air in the tank is initially at 15°C. The tank is left near an engine exhaust line. and the tank's pressure doubles. Determine (a) the final temperature; (b) the change in internal energy; (c) the heat added. (d) AS
A rigid chamber contains 100 kg of water at 500 kPa, 100°C A paddle wheel stirs the water at 1025 rpm with a torque of 145 N-m while an internal electrical resistance heater heats the water, consuming 8.5 amps of current at 110 Volts. Because of thin insulation, the chamber loses heat to surroundings at 27°C at a rate of 1.10 kW. Determine the rate at which the stored energy of the system changes. Express your answer to five significant figures. VO AE It vec ? kW
(2) A well-insulated 106 m³ room initially at 3°C and 88 kPa is heated by the radiator of a steam heating system. The radiator has a volume of 35 L and is filled with superheated vapor at 300 kPa and 250°C. At this moment both the inlet and the exit valves to the radiator are closed. A 100-W fan is used to distribute the air in the room. The pressure of the steam is observed to drop to 100 kPa after 148 min as a result of heat transfer to the room. Assuming constant specific heats for air at room temperature and that the room is perfectly sealed, the temperature rise will be: Fan Steam radiator (а) 8.3 К (b) 9.2 К (с) 10.4 К (d) 11.2 K (е) 12.5 К
6. A well-sealed room contains 60 kg of air at 200 kPa and 25°C. Now solar energy enters the room at an average rate of 0.8 kJ/s while a 120-W fan is turned on to circulate the air in the room. If heat transfer through the walls is negligible, Solve for the air temperature in the room in 30 min. (3 DECIMAL IN FINAL ANSWER PLS)
An adiabatic compressor receives 0.5 kg/s of helium at 175 kPa and 320 K and discharges it at 0.8 MPa. If the specific heat at constant pressure and specific heat at constant volume of helium is 5.19 and 3.12 kJ/(kg-K) respectively, Calculate the following. a. The volume flow rate of helium in cfm. b. The Work of the compressor in kW. c. The brake power in Hp for a compressor efficiency of 78%.
Solve the following problems: Note: Draw the p-h diagram completely labeling the respective refrigerant conditions (pressures and temperatures) and define the properties of refrigerant (enthalpies and specific volume) needed to solve the respective problems. In an ammonia refrigeration system, the capacity is (1) 210 kW at a temperature of-20°C. The vapor from the evaporator is pumped by one compressor to the condensing pressure of 1431 kPa. Later, the system was revised to a two-stage compression operating on the cycle shown below with intercooling but no removal of flash at 555 kPa. (а) Calculate the power required by the single compressor in the original system. (b) Calculate the total power required by the two compressors in the revised system. Condenser 1431kPa High-stage compressor Intercooler 555kPa Evaporator 2í0kW -20°C Low-stage compresaor