Within the green dashed circle shown in the figure below, the magnetic field changes with time according to the expression B = 7.00t³ - 1.00t² + 0.800, where B is in teslas, t is in seconds, and R = 2.65 cm.1xxxxxxxx x197x xx xx xxxxxxxxR*xxxxxxxxxxxxxxxxBinn(a) When t = 2.00 s, calculate the magnitude of the force exerted on an electron located at point P₁, which is at a distance ₁ = 5.30 cm from the center of the circular field region.(b) When t = 2.00 s, calculate the direction of the force exerted on an electron located at point P₁, which is at a distance ₁ = 5.30 cm from the center of the circular field region.O tangent to the electric field line passing through point P₁ and clockwiseO tangent to the electric field line passing through point P₁ and counterclockwiseO The magnitude is zero.(c) At what instant is this force equal to zero? (Consider the time after t = 0 s.)

Answered: Image /qna-images/answer/bb1b1008-36ff-44a7-8288-38bc52aa5cc8.jpg

Answered: (a) When t = 2.00 s, calculate the…

(a) When t = 2.00 s, calculate the magnitude of the force exerted on an electron located at point P₁, which is at a distance r₁= 5.30 cm from the center of the circular field region.

Physics for Scientists and Engineers: Foundations and Connections

1st Edition

ISBN:9781133939146

Author:Katz, Debora M.

Publisher:Katz, Debora M.

Chapter32: Faraday’s Law Of Induction

Section: Chapter Questions

Problem 71PQ: Two frictionless conducting rails separated by l = 55.0 cm are connected through a 2.00- resistor,...

See similar textbooks

Related questions

Q: 1. A large ball rests on an inclined surface as shown below. Draw a proper free body diagram for the…

Q: A new optical imaging satellite is being designed for the Maritime Domain Awareness mission. The…

A: Given that- h=5000km maximum range=7000km The desired resoluction=3m To determine that What is the…

Q: An object of mass ?=8.9 kg is free to move on a horizontal surface without any friction. It is…

A: Given : mass of the object, m =8.9 kg Initial velocity, u = 0 m/s…

Q: Who originally thought of using vacuum tubes to power electronic devices?

A: Introduction: The application of electronics to the control and conversion of electric power is…

Q: A 10.1-V battery, a 5.04-02 resistor, and a 10.7-4 inductor are connected in series. After the…

A: Given: Resistance R = 5.04 ohms Inductance L = 10.7 H are connected in series Voltage E = 10.1 v

Q: When a 200.0-g mass is attached to a spring, it stretches the spring by 7.5 cm. With that…

Q: a. A student tosses a coin into a large wishing well and wishes for good marks in physics. The coin…

A: The x component of initial velocity is The y component of initial velocity is

Q: 7) Which quantity refers to the hindrance offered by a material to the flow charges? Current Voltage…

Q: In cylindrical coordinates, P = Peyt(1, 90°, 1) and Q = Qeyl(0,0°, 1). (a) Determine the length of…

A: Given:Coordinates of P: P=Pcyl1,90°,1Coordinates of Q: Q=Qcyl0,0°,1 To obtain:The length of the line…

Q: Two snowy peaks are at heights H=800 m and h = 740 m above the valley between them. A ski run…

Q: H₂O has a much higher latent heat of vaporization than latent heat of fusion. Therefore, Ice at 0° C…

Q: Fase 3. Then w Physically, this means: -0 and m₂ m (L.e. my my This can be interpreted as: O Large…

A: Since the type of collision is not mentioned in the question whether it is elastic or inelastic.…

Q: The first figure gives spring force F, versus position x for the spring-block arrangement of the…

A: given spring force Fx versus position x for the spring–block arrangement . Fs = 180…

Q: (Ignore the mass of the vertical section of the cord) Vibrator (4) When the vibrator is set to a…

A: Given : The mass is m = 6 kg The length is L = 2 m (a) The frequency is f = 140 Hz, The number of…

Q: Two charges, each 6 µC, are on the x axis, one at the origin and the other at x = 8 m

A: Since you have posted a question with multiple sub-parts, we will solve first three sub-parts for…

Q: A block of iron with volume 12.5 x 10³ m³ contains 3.95 x 10 electrons, with each electron having a…

A: Solution: The magnetization M of a material is defined as the magnetic moment per unit volume of the…

Q: A constellation of radar satellites in LEO orbit is being used to monitor the open ocean. The system…

A: SAR (Synthetic Aperture Radar) is an active remote sensing technology that uses radar pulses to…

Q: An electron is accelerated from rest through 2300 V and then enters a region of uniform magnetic…

Q: A charge of -4.06 C is fixed at the center of a compass. Two additional charges are fixed on the…

A: Charge at center (q) = -4.06 C First additional charge (q1) = -4.27 C due north Second additional…

Q: 7.56 A 1500-kg rocket is Figure P7.56 Rocket starts here. to be launched with an initial upward…

Q: If 1.0 joule of work is required to move 1.0 coulomb of charge between two points in an electric…

A: The required work done is 1.0 J. The magnitude of the charge is 1.0 C. The work done to move a…

Q: cm. Particle 3 of charge magnitude 54.0 μC is released from rest on the yaxis at y = 20.4 cm. What…

Q: A magnetic field has a magnitude of 0.0014 T, and an electric field has a magnitude of 3.5 x 103…

A: Given: Magnetic field is B=0.0014 T along y-direction. Electric field is E=3.5×103 N/C along…

Q: A bridge of length 57 m and mass 80000 kg is supported at each end. A truck of mass 38200 kg is…

Q: Sketch a picture showing how you would store these devices so that they would be safe from excess…

A: To protect electronic devices from excess charges, you can store them in a Faraday cage. A Faraday…

Q: Each of three objects has a net charge. Objects A and B attract one another. Objects B and C also…

A: We know that Like charges Repel each other and unlike charges attract each otherData given in the…

Q: Calculate the impulse imparted to a 0.2 kg tennis ball traveling in the air at 15 m/s when the ball…

Q: A-4.0-μC charge is located 0.45 m to the left of a +6.0-μC charge. What is the magnitude and…

A: The positive charge is +6.0 μC. The location of the charge -4.0 μC is 0.45 m to the left of the…

Q: an airplane travelled at a avreage velocity of 250 km/h[E]. The resulting displacement was 625 km…

A: Avereage velocity, v = 250 km/h[E] Displacement, d = 625 km Time, t = ?

Q: One heater uses 340 W of power when connected by itself to a battery. Another heater uses 210 W of…

A: Given:- The first heater which is connected to the battery of V voltage uses a power P1 = 340W The…

Q: 7.59 CP A 0.300-kg potato is tied to a string with length 2.50 m, and the other end of the string is…

Q: A child with mass 40 kg sits on the edge of a merry-go-round at a distance of 3.0 m from its axis of…

Q: 1. a) A man weighing 765 N is on a bed of nails. Calculate the pressure exerted by each nail if…

A: Given:Weight of man: W=765 NRadius of tip of each nail: rna=5.00×10-4 mRadius of tip of needle:…

Q: Coal miners love physics, and in their spare time, they like to do physics experiments. One popular…

Q: What is the magnitude of the electric field intensity at a point where a proton experiences an…

Q: A force FY shown in the figure below acts on a particle moving along the y axis. Each unit in the…

A: The area under the force displacement graph is work done. a. Work done on the particle from A to B…

Q: 6. Consider a particle of mass m = 22.0 kg revolving around an axis with a constant angular velocity…

Q: shear stress on the rod

A: Given: Diameter of aluminum rod is d=2.9 cm Distance from the wall is L=7.8 cm Mass of object is…

Q: 41. A container of cross-sectional area equal to 1.00 cm² (1.00 x 104 m²) holds a liquid of density…

Q: A parallel-plate air capacitor is to store charge of magnitude 240.0 pC on each plate when the…

Q: Two long parallel wires are separated by 15.2 cm. The wire on the left carries a current of 25.0 A…

A: The magnetic field created by a current-carrying wire is given by the formula: B=μ0I2πr where μ₀ is…

Q: An iron wire with a diameter of 2 mm will be used to connect a voltage source to a 100 kΩ resistor.…

A: Given data: The diameter of the iron wire is d = 2 mm The resistance of the resistor is R=100 kΩ…

Q: The drawing shows four point charges. The value of q is 1.3 μC, and the distance d is 0.84 m. Find…

A: Given:The value of q: q=1.3 μC=1.3×10-6 CThe distance d: d=0.84 m To calculate:The total potential…

Q: An automobile tire is inflated with air originally at 10.0°C and normal atmospheric pressure. During…

Q: Suppose two flat glass plates 30-cm long are in contact along one end and separated by a human hair…

A: The length of the glass plate is 30 cm. The diameter of the hair is 50 μm. The wavelength of the…

Q: Determine the years it would take to go from Mars to Jupiter on a Hohmann ellipse.

A: Solution: To determine the time it would take to go from Mars to Jupiter on a Hohmann ellipse, we…

Q: A charge Q is located at x = 0 and a charge 4Q is at x = 12.0 cm. The force on a charge of -7 µC is…

A: The magnitude of 1st two charges are Q and 4Q. The position of the charge 4Q is at x=12.0 cm. The…

Q: Electricity When voltages V₁ = 50 sin (120mt) and V₂ = 120 cos (120mt) are applied to the same…

A: Given that, The voltages are V1=50sin120πtV2=120cos120πt a) To draw a graph for the sum of the…

Q: h work must you do to push a 13.0 kg block of steel across a steel table (k = 0.60) at a steady…

A: mass of block m = 13.0 kg coefficient of kinetic friction…

Q: The circuit in the drawing contains five identical resistors. The 45-V battery delivers 50 W of…

Concept explainers

Electric Charges and Fields

One of the fundamental properties is the electromagnetic property. Charge cannot be destroyed by any process and this contributes formally to the law of charge conservation.

Question

Within the green dashed circle shown in the figure below, the magnetic field changes with time according to the expression B = 7.00t³ - 1.00t² + 0.800, where B is in teslas, t is in seconds, and R = 2.65 cm.
1
xxxx
xxxx x
197
x xx xx xx
xxx
xxx
R
*
xxxxx
xxxxxx
xxxxx
Bin
n
(a) When t = 2.00 s, calculate the magnitude of the force exerted on an electron located at point P₁, which is at a distance ₁ = 5.30 cm from the center of the circular field region.
(b) When t = 2.00 s, calculate the direction of the force exerted on an electron located at point P₁, which is at a distance ₁ = 5.30 cm from the center of the circular field region.
O tangent to the electric field line passing through point P₁ and clockwise
O tangent to the electric field line passing through point P₁ and counterclockwise
O The magnitude is zero.
(c) At what instant is this force equal to zero? (Consider the time after t = 0 s.)

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, physics and related others by exploring similar questions and additional content below.

Similar questions

A magnetic field directed into the page changes with time according to B = 0.030 0t2 + 1.40, where B is in teslas and t is in seconds. The field has a circular cross section of radius R = 2.50 cm (see Fig. P23.28). When t = 3.00 s and r2 = 0.020 0 m, what are (a) the magnitude and (b) the direction of the electric field at point P2?
Two frictionless conducting rails separated by l = 55.0 cm are connected through a 2.00- resistor, and the circuit is completed by a bar that is free to slide on the rails (Fig. P32.71). A uniform magnetic field of 5.00 T directed out of the page permeates the region, a. What is the magnitude of the force Fp that must be applied so that the bar moves with a constant speed of 1.25 m/s to the right? b. What is the rate at which energy is dissipated through the 2.00- resistor in the circuit?
A cube of edge length l=2.50 cm is positioned as shown in Figure P30.47. A uniform magnetic field given by B = (5 i + 4j + 3k) T exists throughout the region. (a) Calculate the magnetic flux through the shaded face. (b) What is the total flux through the six faces?
A strong magnet is placed under a horizontal conducting ring of radius r that carries current I as shown in Figure P28.27. If the magnetic field B makes an angle with the vertical at the rings location, what are (a) the magnitude and (b) the direction of the resultant magnetic force on the ring? Figure P28.27
The accompanying figure shows a cross-section of a long, hollow, cylindrical conductor of inner radius r1= 3.0 cm and outer radius r2= 5.0 cm. A 50-A current distributed uniformly over the cross-section flows into the page. Calculate the magnetic field at r = 2.0 cm. r = 4.0 cm. and r = 6.0 cm.
How is the percentage change in the strength of the magnetic field across the face of the toroid related to the percentage change in the radial distance from the axis of the toroid?
A magnetic field directed into the page changes with time according to B = 0.031 ot² + 1.40, where B is in teslas and t is in seconds. The field has a circular cross section of radius R = 2.50 cm (see figure below). xxxx vPg xxx xxx xxxx x Rx Bin P₁ (a) When t = 4.80 s and r₂ = 0.020 0 m, what is the magnitude of the electric field at point P₂? 0.00030 X Your response is off by a multiple of ten. N/C (b) When t = 4.80 s and r₂ = 0.020 0 m, what is the direction of the electric field at point P₂? perpendicular to r₂ and counterclockwise O into the page O out of the page. O perpendicular to ₂ and clockwise
A magnetic field directed into the page changes with time according to B = 0.055 Ot? + 1.40, where B is in teslas and t is in seconds. The field has a circular cross section of radius R = 2.50 cm (see figure below). x x x X P. X x x X * x x x R * x x x x x Bin (a) When t = 2.20 s and r, = 0.020 0 m, what is the magnitude of the electric field at point P,? | N/C (b) When t = 2.20 s and r, = 0.020 0 m, what is the direction of the electric field at point P,? O perpendicular to r, and clockwise O out of the page O into the page O perpendicular to r, and counterclockwise
A magnetic field directed into the page changes with time according to B = 0.033 or? + 1.40, where B is in teslas and t is in seconds. The field has a circular cross section of radius R = 2.50 cm (see figure below). * x x x * x x xx x * x x K* x x x x * x x x x x x x x x x x B Din (a) When t= 1.50 s and r, = 0.020 o m, what is the magnitude of the electric field at point p,? N/C
The graph shows the relationship between the magnetic field (B in mT) at the center of a solenoid and the current I (in A). If the solenoid is composed of 33 turns, what is its length in cm? Given that μ = 1.26x10-6 T.m/A B(mT) Round your answer to 1 decimal place. Your Answer: 0.045195 Incorrect The answer is 46.2 ± 5%. Y= 0.092 X + 0.2 I(A)
A magnetic field directed into the page changes with time according to B = 0.035 or? + 1.40, where B is in teslas and t is in seconds. The field has a circular cross section of radius R = 2.50 cm (see figure below). x x x x * * x X x x x xx x X X x x X x x x x x R x * x x x x X x x x x x Bin (a) When := 4.70 s and r = 0.020 0 m, what is the magnitude of the electric field at point P,? N/C (b) When = 4.70 s and r,= 0.020 0 m, what is the direction of the electric field at point P,? O perpendicular to r2 and clockwise O perpendicular to r, and counterclockwise into the page O out of the page
A magnetic field directed into the page changes with time according to B = 0.025 ot2 + 1.40, where B is in teslas and t is in seconds. The field has a circular cross section of radius R = 2.50 cm (see figure below). * x x X x * x x x x2 * x x x 7x x x * x x x * R * x x x x x x x x X x Bin (a) When t = 3.70 s and r, = 0.020 0 m, what is the magnitude of the electric field at point P,? N/C (b) When t = 3.70o s and r, = 0.020 0 m, what is the direction of the electric field at point P,? perpendicular tor, and clockwise perpendicular to r, and counterclockwise out of the page into the page