A wind turbine gives the following data: Blade length= 55.5 m. Wind speed = 11 m/s Air density = 1.227 Kg/m3 Power coefficient = 0.55 Assuming equal efficiencies for gearbox and generator, If the Power output from wind turbine, P is 2.1 MW, then find a) Rotor Power Output, Pr in MW (* b) Wind Power, P, in MW (. C) Efficiency of Generator Outpu

A wind turbine gives the following data: Blade length= 55.5 m. Wind speed = 11 m/s Air density = 1.227 Kg/m3 Power coefficient = 0.55 Assuming equal efficiencies for gearbox and generator, If the Power output from wind turbine, P is 2.1 MW, then find a) Rotor Power Output, Pr in MW (* b) Wind Power, P, in MW (. C) Efficiency of Generator Outpu

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

EX.1 An axial flow pump with an impeller rotor diameter of 30 cm handles water at a rate of 2.7 m?/minute running at 1500 rpm. The energy input is e ——T e T ‘a 125 J/kg and Total to Total efficiency is 0.75. If a geometrically similar pump has a diameter of 20 cm running at 3000 rpm, find its: i) Flow ratei) input power.
1. The wind turbine gives the following data: Blade length, I-52 m, Wind speed, v= 12 m/s, Air density, p=1.23 kg/m, Power Coefficient, C,- 0.4, Calculate
Given: Rotor dia. = 4m; Power coefficient, Cp = 0.35; Ave. wind speed = 6 m/s; Air density = 0.124 kgs^2/m^4; Generator efficiency = 90%. Solve for the 1) Swept Area, 2) Density of Air in kg/m^3, 3) Output power of the windmill, and 4) Available power of the windmill.
B) The air flow to a four cylinder four-stroke engine is 2.15 m³/min. During a test on the engine the following data were recorded: Bore 10.5cm; stroke 12.5cm; engine speed 1200 rpm, torque 150 N.m, fuel consumption 5.5 kg/hr, calorific value of fuel, 43124 kJ/kg, ambient temperature 1-The brake thermal efficiency. and pressure are 20°C and 1.03 barş. Calculate: 2-The brakes mean effective pressure. 3-The volumetric efficiency.
Air pressure pand temperature Tat the inlet of reciprocating compressor are 1 bar and 15 °C. The outlet pressure is 8 bar.The power of the compressor Pis 551.6 W and the volume flow rate of inlet air qy is 122 litres/minute. The rotational speed of the compressor Nis 2850 rpm and the volumetric efficiency ny is 74.0%. Each question is worth of Calculate: a) Suction volume Vsuction b) Displacement volume Vstroke c) Isothermal power Pr cm³ (with one decimal accuracy) d) Isothermal efficiency T cm3 (with one decimal accuracy) W (with zero decimal accuracy) Your last answer was interpreted as follows: % (with zero decimal accuracy) Your last answer was interpreted as follows. Calculate the time t it takes to produce 20 litres of compressed air
P4.54). A four-stroke engine produces an output of 420 kW when operating with mechanical efficiency of 87.5%. The fuel consumption is given as 164 kg/hr when the air consumption is 2780 kg/hr when the fuel heating value is prescribed as 44,200 kJ/kg. Calculate: a) IHP; b) FHP; c) air/fuel ratio; d) Indicated thermal efficiency e) Brake thermal efficiency [Ans: 600 HP; 75 HP; 15.2 ; 30%; 26.2%]
Consider a geographical location where a wind turbine is to be installed with the following data: Wind velocity V, = 40km/hr (11.11 m/s); Atmosphere pressure 101.3kPa, the wind temperature is 20°C, Blade diameter (Rotor swept diameter D = 10m). Determine the following: a) What is the maximum available power, P, available b) What can be the maximum extracted power P, extract c) What is the rotor speed w and torque t.
EX.1 An axial flow pump with an impeller rotor diameter of 30 cm handles water at a rate of 2.7 m*/minute running at 1500 rpm. The energy input is Ko W 125 J/kg and Total to Total efficiency is 0.75. If a geometrically similar pump has a diameter of 20 cm running at 3000 rpm, find its: i) Flow rate ii) input power.
For the model pump below (impeller size: 37.1 cm; shaft speed: 2133.5 rpm), if it is operated to achieve a pump efficiency of 60% at a discharge within the range between 0 and 0.25 m³/s, using a shaft speed of 1800 rpm instead, what will most approximately be the power coefficient? Assume water density 1000 kg/m³. 250 Head, m; power, kW 200 150 100 000 0 50 O 0.69 O 0.73 O 0.88 O 0.52 Efficiency 0.05 Head (AH), m N=2133.5 rpm = 35.6 rps D = 37.1 cm 0.15 Discharge, m³/s 0.10 Power input, kW 0.20 0.25 100 80 60 40 20 0
Solve the ff. The discharge pressure of an air compressor is 5 times the suction pressure. If the volume flow at suction is 0.7m3/s and discharge volume flow of 0.2217m3/s, what is the compressor power(hp) if suction pressure is 100kpa. Ans. 191.72 A double acting air compressor has a cylinder dimension of 50cm x 60cm, 750rpm will have a volume displacement (m3/s) of: Ans. 2.945 A pump has a specific speed of 45 and 600rpm when it delivers 0.01m3/s. Find the head developed by the pump in ft. Ans. 926.07
Q1/ A) An impulse wheel is to be designed to develop at the nozzle pressure is 40 kg/cm and the deflect the jet impinging on them 150°. The center line of the bucket is on a circle of 250 cm find:- 1. The speed of the Pelton wheel (rpm). 2. Efficiency and hours power the theoretical, at the nozzle flow rate 3 m/sec. 3. Specific speed. B) What importance has the ratio? M = (mean diameter of Pelton wheel)/ (least diameter of jet) in designing the Pelton turbine.
Prototype of a mixed flow mini heart support pump at n1= 11000 rpmthe manometric pressure height is 100 mmHg, the flow rate of the blood-like liquid it pumps is 5.5 l/min and the efficiency is 9%. The relative density of this liquid is 1.06. It can be assumed that yields have not changed.a) find the power of the pump at this speed (n1).b) if the speed of this pump is reduced to n2 = 8000 rpm, what is the flow rate, manometric pressure height and power?