2. The horizontal shaft ABCD is attached to a fixed base at A and is subjected to thetorques as shown in Figure Q2. Knowing that the entire shaft is made of aluminiumfor which G = 27GPa,a.b.Determine the maximum shear stress and its location.Angle of twist at end D.ASSIGNMENT 2030Section p-pdDPРØ4020000Section q-q992000161500 NmAll dimensions in mmSection r-r500030SEMU2113500 Nm

Answered: Image /qna-images/answer/927844ef-d4fc-46a2-ab75-b976a6654a97.jpg

a. b. for which G=27GPa, Determine the maximum shear stress and its location. Angle of twist at end D. ASSIGNMENT 2 030 Section p-p A 200 040 B Section q-q 9 200 016 1500 Nm All dimensions in mm Section r-r 500 030 SEMU2113 D 500 Nm

a. b. for which G=27GPa, Determine the maximum shear stress and its location. Angle of twist at end D. ASSIGNMENT 2 030 Section p-p A 200 040 B Section q-q 9 200 016 1500 Nm All dimensions in mm Section r-r 500 030 SEMU2113 D 500 Nm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A solid circular shaft is acted upon by thetorques as shown. If G= 12, 000 ksi determine:a. Rotation of wheel D with respect to A.b. Shear stress at point EDiameter of shaft:A-B = 2inC-D = 2inB-C = 4inT1 = 2.5 π in.kipsT2 = 8.5 π in.kipsT3 = 7 π in.kipsT4 = π in.kips
2. A composite shaft is subjected to two torques as shown below. Shaft AB is a solid aluminum (G = 25 GPa) shaft and is welded to brass (G = 37 GPa) shaft BCD. Segment BC of the brass shaft is solid and the segment CD is hollow with inner diameter of 40 mm. Determine the maximum shear stresses in the aluminum and brass shafts, and the angle of twist of end A. 60 mm T = 1600 N - m 36 mm TA = S00 N - m 250 mm 375 mm 400 mm
3. From the figure shown below, determine the stress of member AB and BC. And calculate the maximum angle of twist of the shaft. 15 kN-m 10 kN-m G = 82.5 GPa A IB diameter = 60 mm diameter = 50mm %3! 1.2 m 0.8 m
The shaft consists of three concentric tubes, each made from the same material and having inner and outer radii as given below. Length of shaft is 2m. One end is fixed to the wall and to the other end a disc is attached. If a torque of T =800 N.m is applied at the disc end, determine the maximum shear stress in the shaft. 1. Inner tube: r; = 20mm, r, = 25 mm 2. Center tube: r; = 26 mm, r. = 30 mm 3. Outer tube: r = 32mm, r, = 38mm
A shaft is made of a steel alloy having an allowable shear stress of Tallow = 12ksi. IF the diameter of the shaft is 1.5 inches diameter the maximum torque T if a 1in, diameter hole is bored through the shaft? Sketch the shear stress distribution along a trial line in each case.
The compound shaft made from the same material consisting of two segments AC and CB is firmly attached to rigid supports. The allowable shear stress in the shaft is limited to 5500 psi. Determine the maximum torque TO that may be applied at C. Calculate also the angular rotation incurred by segment BC. Use G= 12 x 106 psi. (Please provide detailed solution, thank you with FBD) To = ? lb-in ϴBC = ? degree
The compound shaft is attached to a rigid wall at each end. For the bronze segment AB, the diameter is 68 mm and G = 34.84 GPa. For the steel segment BC, the diameter is 40 mm and G = 83.59 GPa. Given that a = 2 m and b = 1.5 m, compute the largest torque T (in Nm) that can be applied as shown in the figure if the maximum shear stress is limited to 69.92 MPa in the bronze and 87.06 MPa in the steel. Round off the final answer to two decimal places. d ... A Bronze B Steel b.
The compound shaft is attached to a rigid wall at each end. For the bronze segment AB, the diameter is 72 mm and G = 30.49 GPa. For the steel segment BC, the diameter is 48 mm and G = 83.57 GPa. Given that a = 2.09 m and b = 1.48 m, compute the largest torque T (in Nm) that can be applied as shown in the figure if the maximum shear stress is limited to 66.49 MPa in the bronze and 85.69 MPa in the steel. Round off the final answer to two decimal places.
The steel shaft of a socket wrench has adiameter of 8.0 mm and a length of 200 mm (seefigure).If the allowable stress in shear is 60 MPa, whatis the maximum permissible torque Tmax that may beexerted with the wrench?Through what angle f (in degrees) will the shafttwist under the action of the maximum torque?(Assume G = 78 GPa and disregard any bending ofthe shaft.)
Q1: The shaft BC is hollow with inner and outer diameters of 100 mm and 120 mm respectively. Shaft AB and CD are solid and of diameter d. For the loading shown determine the maximum and minimum shear stress in shaft BC. 0.9 m 0.7 m d 0.5 m A 120 mm T = 10 kN.m i В TB = = 20 KN.m 1 C D Tc = 30 KN.mi Tp = 6 kN - m Figure Question1
The compound shaft is attached to a rigid wall at each end. For the bronze segment AB, the diameter is 66 mm and G = 34.74 GPa. For the steel segment BC, the diameter is 45 mm and 6 = 84.1 GPa. Given that a = 2.18 m and b = 1.43 m, compute the largest torque T (in Nm) that can be applied as shown in the figure if the maximum shear stress is limited to 65.48 MPa in the bronze and 81.24 MPa in the steel. Round off the final answer to two decimal places. d ... A Bronze B Steel b–
A solid brass shaft is loaded as shown below by two torques TB- segments are LAB = 700 mm and LBC 600 mm. A dBc = dAB mm LAB mm B Com dBC For brass, G = 41 GPa. Neglect the effect of any stress concentrations. LBC Determine the smallest diameters dAB and dBC for which an allowable shear stress of 50 MPa is not exceeded. Express each diameter as an integer in units of mm. dAB To 1100 Nm and Tc = 300 Nm. The lengths of the two Determine the magnitude of the total angle of twist in the shaft caused by the two applied torques for the diameters found previously Express your result in units of radians with five decimal places of accuracy. PAC = rad