Af D Find the stress in each cord of the system shown in fig. below if the cross section area of each cord is ?450 mm2 111111 B 45 с 750 W =90 KN A ܝܝܢܥܠܠ
Q: Calculate the support reaction forces of the truss as illustrated below and the forces on members…
A:
Q: Q3 Ⓡ In figure, two collars A and B slide on the smooth horizontal bar with restitution coefficient…
A:
Q: For the following adiabatic Turbine, calculate: 1- adiabatic efficiency (+)- 2- the mass flow rate…
A: P1= 2 MPaT1= 350∘CP2= 100 kPaT2= 150∘CW˙out= 2.5 MW= 2.5(1000) kW
Q: Show diagrams and calculations to support your answer. Suppose you are a group of cadet engineers…
A: Nominal diameter: 6 inches Schedule Number: 40 Material of Construction: steel
Q: Explain what is meant by the term 'back work ratio' and discuss how the back work ratio differs…
A: Disclaimer: “Since you have asked multiple questions, we will solve the first question for you. If…
Q: Determine the largest load P that can be applied to the structure shown below. All members are made…
A:
Q: 7 ? B 2 ft 4 ft 800 lb/ft y 2.2 m 77 G FIG. P4.17 B 2 ft 120 kN/m - 2.4 m FIG. P4.19 D The 2.2 m 4…
A:
Q: Q4/ One mole of an ideal gas, initially at 20°C and 1 bar, undergoes the following mechanically…
A:
Q: I₂ = 21×106 mm¹ Beam section 2.40 m Y 5.50 KN 105.00 mm 175.00 mm 3 For the beam and cross section…
A: given data F = 5.50 KN bending moment = 5.50×2.40=13.2 kN-m Iz=21×10^6 mm^4 find the tension…
Q: Q1/ A ball is released from the Point A upward with a velocity of 25 m/s. If the ball strikes in the…
A:
Q: Consider a steam power plant that operates on the regenerative Rankine cycle w one open feedwater…
A: INTRODUCTION: A turbine is a device that generates work by expanding intake steam. When…
Q: Q2) A long horizontal wire of 0.2 mm diameter has a constant temperature of 54 C caused by an…
A: Given: Diameter of the wire→d=0.2 mm Outside constant temperature→To=0°C Temperature of the…
Q: At a given section a shaft is subjected to a bending stress of 30 MN/m2 and a shear stress of 60…
A: given data bending stress = 30MN/m^2 shear stress = 60 MN/m^2 find the principal stress and maximum…
Q: 08-The mach number at the exit of a combustion chamber is 0.9. the ratio of stagnation emperatures…
A:
Q: What are the advantages of using I-girders in bridges Report about construction?
A: Following are the advantages of using I-girders in bridges construction: 1. It is capable of…
Q: Q2/ A compound steam engine develops 250 kW at 80 r.p.m. The coefficient of fluctuation of energy as…
A: given data power= 250kw speed = 80rpm fluctuation of energy = 0.15 fluctuation of speed = 1% radius…
Q: and point out the range
A: The plot of polytropic process on P-V and T-S diagram for endothermic, volume decrease, heating and…
Q: Q.7 The condensing and evaporating temperatures of a vapor compression cycle using R134a are 40°C…
A:
Q: 20) The extra portion which must be separated from the extrudate by cutting it just beyond the die…
A: This question is based on the concept of exclusion sheet metal and rolling from manufacturing…
Q: (iv) Consider a steady flow mixing process. Under what conditions will the energy transported into…
A: Steady flow means the properties should remain constant with respect to time at a particular…
Q: Calculate the force on the rod, if the rod is placed at midspan, that will eliminate the deflection…
A: To determine the reaction force in the rod if it is placed at the mis span.
Q: Question 5: For a rolled steel beam of an unsymmetrical I- section as shown, shown in Fig. 5. If the…
A: First calculate the position of neutral axis from bottom surface.
Q: A horizontal Venturi meter (160mm x 80mm) used to measure the flow of oil of sp.gr.= 0.8. Determine…
A: Inlet diameter of venturi meter, d1=160 mm=0.16 mThroat diameter of venturi meter, d2=80 mm =0.08…
Q: Q.2) Draw the shear force and bending moment diagrams for the distributed load and two reaction…
A: First calculate the reactions then draw the Shear force diagram and bending moment diagram
Q: y K * v X A particle is ejected into a moving fluid of velocity v*. The drag force applied by the…
A:
Q: Q3. For a closed end cylinder where the inner radius is 20 mm and outer radius is 40 mm, and the…
A: Given data: ri=20 mmro=40 mmPi=5 MPa Need to determine the minimum and maximum stresses induced in…
Q: A square thread jackscrew has a 2 threads per inch. It is to lift 15 tons. The friction radius of…
A: As per our guidelines we are supposed to solve only 3 subparts if multiple subparts are asked .…
Q: 18. A pump delivers water to a differential elevation of HB - H₁ = 40 ft. Diame- ter of the suction…
A:
Q: An open tank contains water upto a depth of 2 m and above it an oil of specific gravity 0.8 for a…
A: We know that an open tank contains water upto a depth of 2 m and above it an oil of specific geavity…
Q: Water enters a turbine through a 320mm diameter pipe at the rate of 215 lit/s at a pressure at A of…
A:
Q: 3. The 50-kg crate rests on a horizontal surface for which the coefficient of kinetic friction is…
A:
Q: Q. For a specific spring where the load applied is 100 N, coil diameter is 4 mm, spring diameter is…
A: Given data: F=100 Nd=4 mmD=20 mm Need to determine the point where the total shear stress induced in…
Q: Q/For the forces shown in the figure below, determine the magnitude and direction of the sum of the…
A:
Q: A mass weighing 5 lbs. stretches a spring 6 in. If the mass is pushed do contracting the spring a…
A:
Q: Impulse is a product of the force and the for which the force is acting on an object.
A: Time . Impulse = force × time
Q: 3/3 The 100-kg crate is carefully placed with zero velocity on the incline. Describe what happens if…
A:
Q: Q3. For a closed end cylinder where the inner radius is 20 mm and outer radius is 40 mm, and the…
A:
Q: Q.1. Determine the moment of inertia of the shaded area about the x and y axis. y³ = r² 1 m 1 m
A: find the moment of inertia about x and y axis.
Q: Extensive property of a system is one whose value
A: Property are of two type : Intensive Extensive Intensive : These property does not depend upon…
Q: 3 consecutive carnot engines were designed in such a way that the efficiencies are equal. If the…
A:
Q: In figure. 1 v = (25 s-0.15s') m/s, compute car's acceleration at B, where s = 54 m, X= 50m. Je 16 m…
A:
Q: K(+) torg Hokgls 2 Lettr 7 22222 m F(t) = 60SIN (40+) FIND THE STEADY STATE RESPONSE Xss (+) XSS 8
A:
Q: The car in figure moves in a straight line such that for short time its velocity is defined by v =…
A:
Q: Example 3 300 N 3 4 400 N P Q/ The figure above is in equilibrium find the value of the angle and…
A:
Q: 6) is a sheet metal forming process performed by placing a sheet-metal blank over a die cavity and…
A: Only four multiple questions are allowed to solve.
Q: * two plates are fastened by a number of rivets and a tensile load of 300 KN is applied, find the…
A: The number of rivets required is 7.
Q: 0.00 20.00 kN-m 0.00 -28.00 kN-m Moment diagram I₂ = 19×106 mm¹ TT Beam section 79.00 mm 161.00 mm 1…
A: find the maximum tension and compression bending stress.
Q: Q1. For a compressive helical spring which was made of alloy steel with (200MPa) yield stress,…
A: Agahah
Q: Q.2. Determine the moment of inertia of the composite area about the x and y axis. 150 mm -150 mm-…
A: find the moment of inertia about x and y axis.
Q: An ideal refrigeration cycle that has a condenser temperature of 25°C and an evaporator temperature…
A: following is the solution to the above question-
Step by step
Solved in 3 steps with 2 images
- The hollow drill pipe for an oil well (sec figure) is 6,2 in. in outer diameter and 0.75 in. in thickness. Just above the bit, the compressive force in the pipe (due to the weight of the pipe) is 62 kips and the torque (due to drilling) is 185 kip-in. Determine the maximum tensile, compressive, and shear stresses in the drill pipe.The stresses acting on an element are x= 750 psi, y= 600 psi, and xy = 400 psi. Determine the principal stresses and show them on a sketch of a properly oriented element.The stresses on an element are sx= 1000 Psi. sy= 500 psi, and txy= 350 psi. Find the stresses acting on an element oriented at an angle 0 = 250. Show these stresses on the rotated element.
- A punch for making a slotted hole in ID cards is shown in the figure part a. Assume that the hole produced by the punch can be described as a rectangle (12 mm X 3 mm) with two half circles (r = 1.5 mm) on the left and the right sides. If P = 10 N and the thickness of the ID card is 1 mm, what is the average shear stress in the card?‘7.3-11 The stresses on an element are sx= -300 psi and sy= 600 psi. Find the maximum shear stresses on the element and show them on a sketch of a properly oriented clement.Solve the preceding problem if the internal pressure is 3,85 MPa, the diameter is 20 m, the yield stress is 590 MPa, and the factor of safety is 3.0. (a) Determine the required thickness to the nearest millimeter. (b) If the tank wall thickness is 85 mm, what is the maximum permissible internal pressure?
- The stresses acting on a stress element on the arm of a power excavator (see figure) are ax= 52 MPa and txy= 33 MPa (sec figure). What is the allowable range of values for the stress if the maximum shear stress is limited to = 37 MPa?The normal and shear stresses acting on element A are 6500 psi, 17,300 psi, and 2900 psi (see the figure b for Problem 7.2-5). Determine the maximum shear stresses and associated normal stresses and show them on a sketch of a properly oriented element.A spherical balloon is filled with a gas. The outer diameter of the balloon is 20 in. and the thickness is 0,012 in. Calculate the maximum permissible pressure in the balloon if the allowable tensile stress and the allowable shear stress in the balloon are 1 ksi and 0.3 ksi, respectively.
- Two steel rods are welded together (see figure): the seam is oriented at angle ? = 50°. The stresses on the rotated element are sx1=10 ksi, sy1= -12 ksi, and tx1y1= -5 ksi. Find the state of plane stress on the clement if it is rotated clockwise to align the x3 axis with the longitudinal axis of the rods.Solve the preceding problem if the diameter is 480 mm, the pressure is 20 MPa, the yield stress in tension is 975 MPa, the yield stress in shear is 460 MPa, the factor of safety is 2,75, the modulus of elasticity is 210 GPa, Poissorfs ratio is 0.28, and the normal strain must not exceed 1190 x 10" . For part (b), assume that the tank thickness is 8 mm and the measured normal strain is 990 x 10~ .A point On a free surface of a machine point (E = 214Gpa, G= 83Gpa) the stress state is shown on the diagram below Determine all three principle stresses, the average normal stress, the max in plane shear stress, and the absolute max shear stress