electrical power EX) Ageneration station of 10 MW suppledregion of two consumers A and B whereThe Variation of the load is given byconsumers Aconsumersrookwfrom midnight to 8 am gookwfrom midnight to gaimęfrom 9am to 12 noonfromfrom 5pm to 6p.m50ookwfrom 6pm to 7p.m No-loadfrom 7pm to midnight 4000 kw2500kW12 noon to 5pm 8ookwfrom 8am to 1p.m 5ookwfrom 1 Pm to 2 Pm 8ookwfrom 2pm to 5pm 5000 kwfrom 5Pm to midnight 800 kwfind The factors

Answered: Image /qna-images/answer/8879b03b-0aac-4e50-bdc3-7507c273b245.jpg

Ageneration station of 10MW Suppl region of two consumers A and B where The Variation of The load is given by consumers A Consumers B rookw from midnight to 8 am g from midnight to gaims from gam to 12noon 2500kw from 8am to 1p.m 500 rom 12 noon to 5p.m 800kw om 5pm to 6pm 5000kw -om 6pm to 7pm No-load om 7pm to midnight 4000 kw from 1 Pm to 2 Pm Sooku from 2pm to 5pm 5000 k No-load from 5pm to midnight 80- find The factors

Ageneration station of 10MW Suppl region of two consumers A and B where The Variation of The load is given by consumers A Consumers B rookw from midnight to 8 am g from midnight to gaims from gam to 12noon 2500kw from 8am to 1p.m 500 rom 12 noon to 5p.m 800kw om 5pm to 6pm 5000kw -om 6pm to 7pm No-load om 7pm to midnight 4000 kw from 1 Pm to 2 Pm Sooku from 2pm to 5pm 5000 k No-load from 5pm to midnight 80- find The factors

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter6: Power Flows

Section: Chapter Questions

Problem 6.61P

See similar textbooks

Similar questions

The concentration ratio of parabolic trough power plant is typically O a. from 30 to 40 O b. more than 1500 O c. less than 10 O d. from 10 to 20
6. What is the effect of load inductance on the ripple current? 7. i effect of chonnine Bock and boost 8. Wh 9 What chopping 10. At what duty evcle does the load current rinnle current he
[2] A D.C. to D.C. chopper operates from a 48 V battery source into a resistive load of 240hm. The frequency of the chopper is set to 250Hz. When chopper on-time is 1 ms the load power is A. 6W B. 12W C. 24W D. 48W
Please show you detailed solution Number 10 A voltage of 250 volts at 50 Hz is impressed on a circuit having a 60-ohm resistor, 35-?F capacitor, and a 0.25-henry inductor in series. Determine power factor. A. 0.979 C. 0.924 B. 0.862 D. 0.707
Question 3 To reduce the power consumption, the capacitors Complete should be located Marked out of 1.00 O a. As far as possible to the load P Flag question b. Not suitable place O c. As close as possible to the load d. Not too close not too far from the load Question 4 A load 200+j0 ohms is connected across a 250 V and Complete 50 Hz supply. Find the reactive power. Marked out of 1.00 O a. 350 VAR P Flag question O b. 360 VAR O C. zero VAR Od. 420 VAR
Use the information below to answer questions 24 und 25. The voltage across and the current through a load are (10+ j5Y and (2-jiArespecively. 24. What is the reactive power in VArconsumed? D. 0 A. 15 C. 20 D. 25 25. What is the pawer factor of the load? A. 0.8 leading B. 0.8 Jagging. -D. 0.6 ligging C 0.6 leading
The variable resistor R in the circuit is adjusted until it absorbs the maximum average power. * The value of the maximum power transferred to the load is ..W ーj22 jl2 4/0° A 7.4 O 3.8 O 4.8 O none of the above 12,4 O
Computed Rms value (V) 100 E1:A to B E2:A to C 1502 E3:A to D 220. E4:A to F 220 Vac E5:A to G 330 E6:F to G E7:B to C 470 E8:C to D 6802 E9:D to E E10:E to F
A 5-ohm resistor is connected in series with a 25 micro-farad capacitor. A source voltage of 158 volts, 50 Hz supplies the combination. Determine the following: a. Circulating current b. Voltage across the resistor c. Voltage across the capacitor d. Real power supplied by the source e. Reactive power supplied by the source f. Apparent power of the circuit g. Power factor of the entire circuit
2. A triangular voltage source has a peak value of 10 V. What is the computed RMS value of this source? a. 3 V b. 4 V c. 5 V d. 6 V 3. In Question 2, if the source is measured by an analog meter, will it show the correct RMS value? a. Yes b. No
In case RL load, it is desired to get an average load voltage of 75 V. Determine the firing angle if the ac supply voltage is 200V per phase. If the load resistance is 302, calculate the average load current and power. Design the thyristor. 4-
Oscope CH1 Connection point Function Generator "LOAD" RG R2 R3 1.0027k ohms 66.98 ohms 220.6 ohms 10 Vpk 1kHz 0° L13 103.06 mH 1.015 C2 109.58 nF nF R1 99.712 ohms Oscope CH2 Connection point What is the calculated phase angle between the load voltage and current? Using the calculated phase angle and the RMS voltage/current from the meter to calculate (a) PF, (b) apparent power, (c) average power, (d) reactive power, and (e) complex power Does the amplitude of the output waveform agree with what it should be from the circuit values? Below are the measured voltages and currents.