Air flows steadily at the rate of 0.4 through an air compressor, entering at6" with a pressure of 1 bar and a specific volume of 0.85 leaving at 4.5kgwith a pressure of 6.9 bar and specific volume of 0.16The specific internalkgenergy of the air leaving is 88 4 greater than that of the air entering. The heatloss is 59 . Calculate the work required to drive the compressor in KW.

Answered: Image /qna-images/answer/16a144e4-c513-4223-9497-1ef186a28999.jpg

Answered: Air flows steadily at the rate of 0.4…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

200Kg/min superheated steam at 40 bar and 350C enters a turbine through a 7.5cm ID pipe. It exits at 5bar as saturated steam through a 5cm ID pipe neglect the change in potential energy of the system. What is the temperature of the outlet saturated system? How much energy is transferred to or from the turbine?
During an isentropic non-flow process with air, the pressure drops from 75psia to 30psia. The air has mass of 0.25 lbm and the initial temperature was 265°F. Find: a. The final temperature, in °F b. The heat transferred, in BTU C. The change in internal energy, in BTU d. The work done, in BTU
Exactly 10 kg of steam entered a heat exchanger at 100 bar and 560o C. At the exit the Steam was at 30 bar and a quality of 0.47. Please determine a. The exit temperature in oC. b. The mass of the liquid water in kg.
In a process plant, water is flowing through a globe valve. The pressure before the entering the globe valve is 10 bar and the velocity through a 100 mm valve inlet is 4 m/s. The valve is horizontally placed and when it is 50% open the downstream pressure is observed to be 2 bar. The outlet section of the valve has same diameter as the inlet section. Calculate the power needed to for water to flow through this valve. 4.28 kW 8.28 kW 10.28 kW None of the above O 6.28 kW
Air flows steadily through an engine at a constant temperature, 400K. Find the work per kilogram if the exit pressure is one-third the inlet pressure and the inlet pressure is 207 kPa. Assume that the kinetic and potential energy variation is negligible.
4. A compressor draws in 500 min ft³ of air whose density is 0.079 lb and discharges lb At the suction, P, = 15 - lb it with a density of 0.304 and at the discharge, in? lb The increase in the specific internal energy is 33.8 Btu and the lb P2 = 80 in? Btu heat from the air by cooling is 13. Neglecting changes in the potential and lb Btu kinetic energy determine the work done on the air in min and in horsepower.
Q1: A heat engine used a steam as working fluid has 3 kg/s and initial the steam undergoes to expansion process is 8 bar, dryness fraction (32) percent, and the expansion follows the law (PVL-C), down to a pressure of 0.3 bar. Calculate the change of entropy of steam during the process. . ,.¢
1.4 1kg of a fluid expands reversibly according to a lincar law from 4.2 bar to 14 bar; the initial and final volumes are 0.004 m' and 002 m. The fluid is then cooled reversibly at constant pressure, and finally compressed reversibly according to a law pe= constant back to the initial conditions of 4.2 bar and 004 m. Calculate the work done in cach process and the net work of the cycle. Sketch the cycle on a p- diagram. (-4480 N m: +1120N m, + 1845 N m, -15IS N m)
A steam turbine receives steam with a specific enthalpy of 31 17 kJ/kg at a rate of 5 kg/s. At the turbine outlet, the specific enthalpy of the steam is 2851 kJIkg. Find the turbine power in kW.
1.Atmospheric air enters a single stage screw compressor at 1 bar and 250C at low velocity. The compressor element compresses the air to 3bar which exits through a nozzle in which it expands to a velocity of 600m/s. Before the 7compressed air exits the compressor, it is cooled by an after cooler. If the work of compression is 240kj/kg of air; calculatea) The heat that needs to be taken away by the after cooler. A pump is required to pump out water from a flooding pit at a rate of 1000L/min. With the aid of a well labeled diagram;b) What kind of pump is required for the operation and why?
8. A single stage air compressor handles 0.454 cubic meter per sec of atmospheric pressure, 27 deg Cair and delivers it to a receiver at 652. 75 kPa. It is 0.85 and its mechanical efficiency is 0.90. If it rotates at 500 rpm, what power in kw is required to drive it?
Air is used as a working substance in a given internal combustion engine, which is supplied with heat at a constant volume. Based on the data, calculate the The work of the cycle.

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS

Air flows steadily at the rate of 0.4 through an air compressor, entering at 6 with a pressure of 1 bar and a specific volume of 0.85 leaving at 4.5 with a pressure of 6.9 bar and specific volume of 0.16 kg The specific internal