Air flows through a long, isentropic nozzle. The temperature and pressure at the reservoir are 1000K and 20 atm, respectively. If the Mach number at the entrance is 0.2, determine the gas velocity at the entrance. 634 m/s O127 m/s 478 m/s 254 m/s For a large centrifugal pump, the required net positive suction head is typically around O 5 ft 2 ft 15 ft

Air flows through a long, isentropic nozzle. The temperature and pressure at the reservoir are 1000K and 20 atm, respectively. If the Mach number at the entrance is 0.2, determine the gas velocity at the entrance. 634 m/s O127 m/s 478 m/s 254 m/s For a large centrifugal pump, the required net positive suction head is typically around O 5 ft 2 ft 15 ft

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

n aircraft is flying at an altitude of 12000 metres (T=216.65 K. p = 0.193 bar) at a Mach number of 0.82. The cross sectional area of the inlet diffuser before the L.P. compressor stage is 0.5 m. Determine (a) the mass of air entering the compressor per second (b) the speed of the aircraft (c) the stagnation %3D pressure and temperature of air at the diffuser entry.
(b) Air flows through a cylindrical duct at a rate of 2.3 kg/s. Friction between air and the duct and friction within air can be neglected. The diameter of the duct is 10cm and the air temperature and pressure at the inlet are T₁ 450 K and P₁ = 200 kPa. If the Mach number at the exit is Ma2 determine the rate of heat transfer and the pressure difference across the duct. The constant pressure specific heat of air is cp = 1.005 kJ/kg-K. The gas constant of air is R = 0.287 kJ/kg-K and assume k = 1.4. -
Q.2. Air flows through a constant-area duct is connected to a reservoir at a temperature of 500°C and a pressure of 500 kPa by a converging nozzle, as shown in Figure. Heat is lost at the rate of 250 kJ /kg. Determine the exit pressure and Mach number and the mass flow rate for a back pressure of 0 kPa. q = 250 kJ/kg Pr = 500 kPa Tr = 500°C Po = 0 kPa D= 0.02m
Air enters a 5-cm-diameter duct at Mach number = 0.2, a temperature of 550 K and a pressure of 200 kPa. The average friction factor for the duct is 0.016. If the Mach number at the duct exit is 0.8, determine the pressure at the duct exit. (For air constant R = 287 J/kg.K, specific heat ratio K = 1.4). Select one: a. 65.95 kPa b. 54.85 kPa c. 80.75 kPa d. 47.27 kPa
Q.2. Air flows through a constant-area duct is connected to a reservoir at a temperature of 500°C and a pressure of 500 kPa by a converging nozzle, as shown in Figure. Heat is lost at the rate of 250 kJ /kg. Determine the exit pressure and Mach number and the mass flow rate for a back pressure of 0 kPa. q = 250 kJ/kg P. = 500 kPa T, = 500°C Po = 0 kPa D = 0.02m
Question Four Air flows steadily adiabatically through a pipe with a cross-sectional of 0.002 m?. At the inlet of the duct, the pressure and temperature are 100 kPa and 50°C, respectively. At the exit of the duct, the temperature and velocity are 100°C and 600 m/s, respectively. Determine the Mach number and the velocity at the inlet section. Also, calculate the mass flow rate. Ans. M 1.884, vi = 678.7 m/s, m = 1.46 kg/s.
· A converging diverging nozzle is conneted to a large air reservoir with Problem 3 . Ehe pressure and temperature of 1.0 MPa and 40 °C. The exit area of the nozzle is 0.5 m2. If the exit mach number is equal to 1.8, determine the following paraneters at the nozzle exit: a) Pressure, b) Temperature, c) Velocity, d) Mass flow rate.
Air enters a rectangular duct at T₁ = 300 K, P₁ = = 420 kPa, and Ma₁ = 2. Heat is transferred to the air in the = amount of 55 kJ/kg as it flows through the duct. Disregarding frictional losses, determine the temperature and Mach number at the duct exit.
5-Which of the following is true for a Fanno flow (a) The Mach number always increases as one moves downstream (b) The static pressure always decreases as one moves downstream (c) The maximum length of the duct is the sonic length (d) none of the above
Q.2. Air flows through a constant-area duct is connected to a reservoir at a temperature of 500°C and a pressure of 500 kPa by a converging nozzle, as shown in Figure. Heat is lost at the rate of 250 kJ /kg. Determine the exit pressure and Mach number and the mass flow rate for a back pressure of 0 kPa. q= 250 kJ/kg P.= 500 kPa T; = 500°C p. = 0 kPa D=0.02m
What is the mass flow rate of air at the exit if the inlet has a Mach number of 0.45, an area of 3ft^2, and has standard atmospheric conditions? Your answer
What is the Mach of airflow with 150 m/s at a pressure of 0.95 atm and a Density of 1.15 kg/m^3?