An 8 m simple beam is loaded with a 228 kN point load at the first third of its length. The cross section of the beam is shown below. If the allowable stress is 200 MPa the thickness of the cross section is constantly t - 18 mm C t C Y A 12 Find the dimension c of the cross section such that it will satisfy the allowable stress. Select the correct response 318.329 mm 290.593 mm 355.903 mm 263.312 mm

An 8 m simple beam is loaded with a 228 kN point load at the first third of its length. The cross section of the beam is shown below. If the allowable stress is 200 MPa the thickness of the cross section is constantly t - 18 mm C t C Y A 12 Find the dimension c of the cross section such that it will satisfy the allowable stress. Select the correct response 318.329 mm 290.593 mm 355.903 mm 263.312 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Two plate are joint by five rivets of 20 mm diameter. What is the shear stress in the material if the shear forces is 18840 N O 12 N/mm2 O 20 N/mm2 O 15 N/mm2
A beam ABC with an overhang from B toC supports a uniform load of 200 lb/ft throughout itslength (see figure). The beam is a channel section withdimensions as shown in the figure. The moment of inertiaabout the z axis (the neutral axis) equals 8.13 in4.(a) Calculate the maximum tensile stress σt andmaximum compressive stress σc due to theuniform load.(b) Find the required span length a that results inthe ratio of larger to smaller compressive stressbeing equal to the ratio of larger to smaller tensilestress for the beam. Assume that the totallength L =a + b = 18 ft remains unchanged.
PROBLEM 37: A sieel secion havung a Cioss seciion c: 20 mm x 30 mm is subjected to an axial force of 240 KN The steel section has produces a strain of 0.002. If it has a value of Poissons ratio of 0.30.Find the shear modulus a. 76923 MPa b. 73852 MPa C. 78023 MPa d. 80256 MPa
Compute for the maximum allowable distributed load o that can be applied to the simply supported beam as shown in Figure M-Va. The beam's cross section is detailed in Figure M-Vb. @(N/m) Allowable Stresses: Fiber Stress = +13.5 MPa / -12 MPa Transverse Shear Stress at NA = 900 kPa Transverse Shear Stress at Junction 800 2 m Figure M-Va 2 m Draw the flexural and shear stress distributions of the cross section. T 40 40 40 Figure M-Vb 40 120 mm
A thin polymer plate PQR is deformed so that corner Q is displaced downward by a distance L = 1.45 mm to new position Q' as shown. Determine the shear strain at Q' associated with the two edges (PQ and QR). 120 mm 480 mm. P R 240 mm -2692 μrad -3352 μrad O-4917 prad -3610 μrad O-2921 urad Q 'Q' X
A beam having the cross section shown is subjected to a couple M0 acting in a vertical plane. Determine the largest permissible value of the moment M0 of the couple if the maximum stress is not to exceed 103 MPa. Given: Iy = Iz = b4/36 Iyz = b4/72
Question: A 12 mm thick plate is connected to two 8 mm thick plates, on either side through a 16 mm diameter power driven field rivet as shown in the figure below. Assuming permissible shear stress as 9- MPa and permissible bearing stress as 270 MPa in the rivet, the rivet value of the joint is P/2 - F 8 mm 8 mm ↓ 12 mm P
If the beam is subjected to an internal moment of M = 30 kN.m, determine the maximum bending stress in the beam. The beam is made from A992 steel. Sketch the bending stress distribution on the cross section. 50 mm 50 mm 15 mm 10 mm M 150 mm 15 mm
Consider the singly reinforced beam section given below (left figure). The stress block parameters for the cross-section from IS: 456: 2000 are also given below (right figure). The moment of resistance for the given section by the limit state method is kN-m. 300 mm M25 4-120 Fe415 200 mm 0.42x 0.36 um = 0.48d for Fe415
Practice 2 A fixed ended steel beam 8m long carries a uniform load 20kN/m and an axial tensile force of 200KN. The properties of steel section is as follows: A = 7800 mm? d = 324 mm Ix = 140x10 mm ly = 16x10 mmt What is the axial stress of the beam, in MPa. What is the actual bending stress in the beam due to uniform load alone acting on the beam, in MPa. -. What is the interaction value if Fb = 210 MPa and Ft = 100 MPa? answer key а.)25.64 Мра b.) 123.43 Мра c.) 0.844
A beam with a channel section is subjected to a bending moment M having its vector at an angle e to the z-axis (see figure). M Determine the orientation of the neutral axis B (in degrees clockwise from the +z-axis) and calculate the maximum tensile stress o, and maximum compressive stress o, in the beam. (For the stresses, enter your answers in ksi and use the deformation sign convention. To solve this problem, be sure to draw a sketch of the cross section showing the orientation of the neutral axis and the locations of the points where the stresses are being found.) Use the following data: C8 x 11.5 section, M = 44 kip-in., tan(6) = See this table for the dimensions and properties of the channel section. B = • clockwise from the +z-axis O: = ksi ksi
Problem 2 The rigid bar is plnned at A and held by two flexible bars at E and C. The load P Is applled at B. The two flexible bars FE and DC each have a diameter of 1 In. The flexible bars are elastic- perfectly plastic with a yleld stress equal to 20 ksl and a yleld strain of 0.001. Determine the following: The load R, at first yleld and the corresponding deflection at B, &, The ultimate load Pu and the corresponding deflection du The permanent deflection and residual stresses in each rod if the ultimate load is removed Construct P - A curve showing yield, ultimate and permanent deformation o (ksi) 1 ft E F 1 ft1 ft 20 B P e (in./in.) 0.001 1 ft D 2 ft 1 ft A