An audio signal having the highest frequency of fM = 15 kHz is input to a 16-bit A/Dcounter type converter. If the pulse repetition period of clock is 0.15 us, themaximum conversion time is:U1INPUTREGISTER /COUNTER07 06 05 04 03 02 01 0007 06 05 04 03 02 01 0OUTPUT REGISTER03 02 01 DO▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬TITOutput Converted Word9.83 ns38.25 μs4.65 με9.83 msU2U4COMPARATORDSDIVinInput Analog SignalU3D/A CONVERTER

Answered: Image /qna-images/answer/c30a4681-25e9-434c-adcc-587ee0b76138.jpg

An audio signal having the highest frequency of fM = 15 kHz is input to a 16-bit A/D counter type converter. If the pulse repetition period of clock is 0.15 us, the maximum conversion time is: U1 INPUT REGISTER /COUNTER 27, of 08 04 03 02 01 00 07 06 05 04 03 02 01 07 OUTPUT REGISTER ▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬TT Output Converted Word 9.83 ns 38.25 μs 4.65 μs 9.83 ms U2 U4 COMPARATOR DI Vin Input Analog Signal U3 D/A CONVERTER

An audio signal having the highest frequency of fM = 15 kHz is input to a 16-bit A/D counter type converter. If the pulse repetition period of clock is 0.15 us, the maximum conversion time is: U1 INPUT REGISTER /COUNTER 27, of 08 04 03 02 01 00 07 06 05 04 03 02 01 07 OUTPUT REGISTER ▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬TT Output Converted Word 9.83 ns 38.25 μs 4.65 μs 9.83 ms U2 U4 COMPARATOR DI Vin Input Analog Signal U3 D/A CONVERTER

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Fast plz , digital signal
The maximum peak-to-peak value of an AM wave is 45 V. The peak-to-peak value of the modulating signal is 20 V. What is the percentage of modulation?
wit Determine Ssketch the output voltage mave form? 1MF- pvi/v 200KR Viown 80807 -4
You need to produce a square wave with a low voltage of 0.500 volts and a high voltage of 2.500 volts. The DAC is 12 bits with a Vref of 3.3 volts. What is the input code for the low voltage and the high voltage? Low: 601, High 3003 Low: 621, High: 3103 Low: 591, High: 2903 Low: 621, High: 2103 3 O O O O
Using two astable M.V timer .Desine the wave form shown in the figure below with Vcc=9v, C=1.6234.Mi . then 1-Determine the duty cycle and the frequency at the output of each M.V timer 2- Draw Vc and Vo at each cct. output o/P 9.1 25 27 29.1 38.2 50 52 58.2 ms
Do the following: a.)Convert 0.7692*10-9 Hz into Mrad/s b.)Convert 22*10-9 Hz into Grad/s
1 6. Calculate the efficiency for each circuit. 7. Name the advantages and disadvantages of each circuit. 8. What is the out frequency of each circuit? 9. Explain how the negative half of the input signal convert in bridge circuit, convert to positive out put. 10. What is the ripple voltage? How can you remove it? 9114.3 -3- AC 1k
1 In a certain digital waveform, the period is two times the pulse width. The duty cycle is 50% The given hexadecimal number 2B.3116 is equivalent to 53.1428 An octal equivalent for fraction decimal number is obtained using repeated division-by-8. 2.
Draw a diagram for astable multivibrator using 555 timer. Find the oscillation frequency of the output signal and its duty cycle when the external capacitor is 0.01 uF, the R1 and R2 are 10 kn and 50 kn respectively. While the decoupling capacitor equal 0.1 µF. What happened to the duty cycle when R2 become 1M02?
Assessment E U Problem 1: Suppose you have a clock signal generator with a frequency of IKHZ but want a 250KHZ Hz and a 250 Hz clock signals for your design. How would you do that? Draw block diagram of circuit and identify all inputs/outputs signal frequencies.
Draw the AM waveform, if the modulating signal is a sine waveform and the percentage modulation is 100%.
QUESTION 24 1165:0100 B84518 1165:0103 BB3478 1165:0106 01C3 1165:0108 48 1165:0109 4B 1165:010A 891E0001 1165:010E CD20 MOV AX, 1845 BX, 7834 BX, AX MOV ADD DEC AX DEC MOV BX (01001, BX 20 INT You have used DEBUG to unassemble the above code. The instruction stored at the address 010A is bytes long. 2 O 16 4.