An extruded aluminum beam has the cross section shown. Knowing that the vertical shear in the beam is 10 kips, determine the shearing stress at (a) point a, (b) point b. 2.4 in. 0.5 in. 0.25 in. 0.25 in. 4 in. a -0.5 in. t 1.2 in. 4

An extruded aluminum beam has the cross section shown. Knowing that the vertical shear in the beam is 10 kips, determine the shearing stress at (a) point a, (b) point b. 2.4 in. 0.5 in. 0.25 in. 0.25 in. 4 in. a -0.5 in. t 1.2 in. 4

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: In trying to minimise errors that come with using a tape in linear measurements, Mapalo suggested to…

A: frequency of 1.4985MHz was usedc = 299792458m/s, refraction index is 1.0003To finddetermine the…

Q: upan For a sag vertical curve shown in the figure bel- Sta. 7+00 -2.3%

Q: The tank contains water, oil (S=0.8) and the pressure of the air with (90Kpa), the mass of the ate…

Q: Determine the least-weight W shape simply supported beam to carry a uniformly distributed dead load…

Q: 14 ..... (Units are cm) 1) a) Locate the centroid of the area. b) Determine the moment of inertia…

Q: Determine the 4 storey period and modal matrix.(Derive) (i need the RED CIRCLED) P.S.An example is…

A: The objective of the question is to determine the period and modal matrix for a 4-storey building…

Q: Q13: A sharp crested weir of 1m height is fixed across 5m wide channel as shown in the following…

Q: Draw a warren truss that is statically determinant with hieght of 4m and lenght of 32m. and prove…

A: Warren trussSpan = 32mHeight = 4mChoosing 4m member each, the Diagram of the truss is shown below

Q: can someone please help me with this? Thank you -) A short square steel structural tube is used as a…

Q: At 14 days, with a hydration degree of 40% the cement paste represents 50% of the total volume.…

A: Given:-The specific gravity of the cement = 3.14The type of cement used = ASTM type IIThe degree of…

Q: Item 1 Part A Determine the horizontal distance between two points A and B whose elevations above…

Q: the level of water at A to maintain a constant depth of 11 ft. If the 50(10³) lb, determine the…

Q: Design a pipe culvert to be provided for a highway embankment across a small valley having the…

A: Culvert is characterized as a passage structure developed under streets or rail routes to give cross…

Q: A 5 m high retaining wall is supporting the soil having properties as shown below: 5m = 30° c=10…

A: For Given retaining wall,To find the rankine earth pressure (per meter length) on the wall after the…

Q: Problem #1: Find the value of the vertical reaction at B (By). Use orce method. (El is Constant). |…

A: Beam is supported at two points A and B, with a uniformly distributed load of 8kN/m acting on it.To…

Q: in a tensile test, a test piece of 25 mm diameter is tested over a gauge length of 125 mm. The…

A: Data given:-Elongation = 0.0875mmP = 68725NAngle of twist = 0.025 radl = 250mm

Q: A rectangular tank 7m long by 2.4m deep and 2.65m wide, contains 1.2m of water. If the linear…

A: L = 7m d = 2.4m b = 2.65m NOTE : As per guidelines, first 3 parts are solved. Request you to post…

Q: 9-5 Determine the deflections of point C and E. Knowing E=2.0X10³ MPa, I,= 1₂=12430 cm². Thin 2m 130…

Q: It is proposed to build an 8 story building with a footprint of 15 m × 20 m, resting on a mat…

Q: PROBLEM6: In a forced vibration test under harmonic excitation it was noted that the amplitude of…

A: As per the given data in the question.The four times the amplitude at an excitation frequency is 20%…

Q: 1. Determine the axial stresses in members CH, AH, and CD of the loaded truss if they have a uniform…

A: The cross-sectional area of the member is 1800 mm2.Consider the figure,

Q: Class I two-lane highway is on rolling terrain and the free-flow speed was measured at 56 mi/h, but…

A: V = 324 + 216 = 540 veh/hour.pt = (percentage of heavy vehicle) = 5% = 0.05Et (passenger car…

Q: The uniform rod is subjected to the axial loads as shown. Which segment has the absolute maximum…

A: Given Loads To find out Which segment has Maximum normal stress

Q: An oil of viscosity 0.02 Ns/m² is flowing between two stationary parallel plates 1 m wide maintained…

Q: The factor of safety against wedge failure along interface for the soil mass along with properties…

A: For given soil profile to find the factor of safety against wedge failure

Q: 2) The vertical bar AB has a mass of 100+ab kg with center of mass G midway between the ends. The…

A: The vertical bar AB has a mass of 126 kgcouple = 11 kNmThe center of mass is GTo determine:The…

Q: e effective ‘factor of safety’ for the following loads on a steel column (show all work): a. The…

A: (a) first column dataLive load = 3 times of dead load snow load = 1/2 times of dead loadThe safety…

Q: A simply supported beam is shown below. There is a mass (m) of 800 lb placed at midspan m L=30' e…

A: Mass = 800 lbE=29000ksiI=1000 inch4

Q: building of Figl is 200 kg and the building is set into free vibration by releasing it (am time t =…

A: The mass of the building is,To determine:a) The lateral spring stiffnessb) Damping ratioc) Damping…

Q: Problem 4 Given the following Muther's grid with 6 departments: Department 1 Department 2 Department…

A: Muther's grid is a facility layout planning tool used to determine the optimal arrangement of…

Q: A singly drained clay deposit 10 meters thick has a coefficient of consolidation of 2.0 x 10-4 cm2 /…

A: Given:Single drainedThickness = 10 m = (10*100) cmCoefficient of consolidation= 2*10-4 cm2/sUltimate…

Q: The 8 ft diameter cylinder weighs 500 lb and rest on the bottom of the tank that is 3ft long, water…

A: the 8ft cylinder weighs W =500 lb and rest on the bottom of the tank.the length of the tank Lt=3 ft…

Q: EXAMPLE: Waterworks of a town treat 35 x 106 litres/day. The water is treated by…

A: Given data - Q = 35×106 L/day Consumed filter alum = 20 mg/L Alkalinity of water = 4.5 mg/L of CaCo3…

Q: 1. A continuous footing is shown in the figure below. Using Terzaghi's ultimate b.c. equation and…

A: = 112 pcf c' = 450 psf = 22o Df = 4ft B = 3 ft FS = 3 NOTE : As per guidelines, first question is…

Q: In a smooth pipe of uniform diameter 30 cm a pressure of 60 kPa was observed at section 1 which was…

Q: 5. Find the level of service of the following road: (45 points) ▪ ▪ 6-lane multilane highway,…

A: The objective of the question is to determine the level of service (LOS) of a given road. The LOS is…

Q: 1.14 TAMI Compute the required area of steel reinforcement for the interior beam shown in Fig.3.35…

Q: Option 3: column design. provide the design calculations and the reinforcement drawings for a Column…

A: The objective of the question is to design a tied column and provide the design calculations and…

Q: 3. The 500-kg uniform beam is subjected to the three external loads shown. Compute the reactions at…

A: The beam weight = 500 kgThe reactions at the support point O =?

Q: Industrial pipes Given the advantages of modeling pipes through interactive 3D software, can…

A: Industrial pipesGiven the advantages of modeling pipes through interactive 3D software, can process…

Q: A beam ABCDE is 4.6 m in length and loaded as shown in for the beam, indicating all major values. 30…

A: Given:Required:Shear force and bending moment diagram

Q: A 3.0 m cantilever beam 360mm wide and having an effective depth of 520mm carries a service dead…

A: length of beam(L) = 3 mwidth of beam(b) = 360 mmeffective depth (d) = 520 mmdead load = 30 KN and…

Q: A wooden pile is being driven with a drop hammer weighing 30 kN and having a free fall of 1 m. The…

Q: Of what value is 'conflict resolution' to a construction contractor?

A: Given that

Q: A class I two-lane highway is on Rolling terrain with a measured free-flow speed of 90 km/h. and 80%…

A: Class I two lane highway FFS = 90 kmph 80% no passing zonesPHF = 0.87 PT = 5%PR = 10%

Q: Design an expansion transition for a canal for the following data, using Mitra's method. Length of…

A: Length of flume=20mWidth of throat=9mWidth of canal=16mFINDDesign an expansion transition for a…

Q: For the given problem, the failure plane was inclined at an angle of 35° with the vertical to find…

Q: Q3// The field capacity of a certain soil 20% and the moisture content of the soil before irrigation…

Q: Q.2) In an unconfined compression (UC) test on a saturated clay, the maximum proving ring dial…

A: Given that :-Maximum proving ring dial reading recorded = Initial height = 70 mmInitial diameter =…

Q: Im 0.5 m 0.5 m 0.5 m B D 1 m- 0.5 m E

A: carrier system is givensupported at A and CG=2KNFindthe vertical support reactions and the rod…

Concept explainers

Planar Stresses

Question

An extruded aluminum beam has the cross section shown. Knowing that the vertical shear in
the beam is 10 kips, determine the shearing stress at (a) point a, (b) point b.
2.4 in.
0.5 in.
0.25 in.
0.25 in.
4 in.
a
-0.5 in.
t
1.2 in.
4

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: At point A

VIEW

Step 2: At point B

VIEW

Solution

VIEW

Step by step

Solved in 3 steps with 12 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

H.W 2 A steel tee shape is used to support the loads shown on the beam in Figure 2 a. dimensions of the shape are shown in Figure 2 b. determine: (a) the maximum tension bending stress at any location along the beam, and (b) the maximum compression bending stress at any location along the beam. The Consider the entire 24-ft length of the beam and 16.00 in. y 7 kips 16 kips 17 kips 1.50 in. 6 kips/ft 18.50 in. В C E 6 ft 4 ft 10 ft 4 ft 0.75 in. FIGURE 2 a. FIGURE 2 b.
PROBLEM 4.9 25 mm Two vertical forces are applied to a beam of the cross section shown. Determine the maximum tensile and compressive stresses in portion BC of the beam. 25 inm 4 kN 4 kN A 300 mm 300 mm
The wood beam has a rectangular cross section in the proportion shown. The allowable bending stress iss =10 MPa. 500 N/m 1.5 b OB - x m 2 m 2 m Calculate the centroid of the cross section of the beam O (1.5b, 1.5b] O (1.5b/2), (1.5b/2)] O (0.(1.5b/2)] O (0,0) [(1.5b/2), 0] O (0, 1.5b)
Determine the shear stress at points: A, B. C, D and E in beam shown in Figure 5. Take E-30 GPa
3. Determine the maximum tensile and compressive bending stresses in the beam shown. 4 kN/m A 10 kN 6 m B 0.5mm 10mm 5mm 0.5mm 0.5mm 15mm
The Figure below shows a two-member truss supporting a block of weight W. The cross-sectional areas of the members are 800 mm² for AB and 400 mm² for AC. Determine the maximum safe value of W (kN) if the working stresses are 110 MPa for AB and 120 MPa for AC. ... B 40 deg. A 60 deg. A) 38.90 в) 55.30 61.70 76.2
A:Y 211O 2_531929016114... -> A rod is composed of an aluminum section rigidly attached between steel and bronze sections, as shown in Figure below. Axial loads are applied at the positions indicated. If P = 11 KN and the cross sectional area of each rod is 312.5 mm, determine the stress in each section. 4P Steel Bronze |Aluminum 609.6 mm 914.4 mm 762 mm
To lower ends of the three bars in the figure two are the same level before the rigid homogeneous W=176kN block is attached. Each still bar has a length of 1.00 m, an area 500mm² and E=200 GPa. For the bronze bar the length is 1.6m, the area is 900mm² and E= 83 GPa. What is the stress developed in the bronze bar? What is the stress developed into steel bar? What is the elongation of each bar?
Cross section of each bar 350 mm2 . Find stress in bar CD
A cantilever beam subjected to a concentrated load at the end of its 6m length. If the allowable shearing stress at the neutral axis is 2MPa, determine the maximum tensile stress in the beam due to the maximum allowable load P. Use a flange thickness of 100 mm. 70.7 MPa 31.3 MPa 62.611 MPa 35 389 MPa
P A B 1m E 1m 2m The simply supported beam shown has a solid rectangular cross section having beam width of 130mm and a height of 200mm. Assuming values of P = 25KN, w = 30 kN/m, and E = 5m, determine: 1) The max tensile bending stress in MPa (enter this value into D2L answer box, in MPa). Exactly where does this occur along the beam? (4 sigs) 2) The max shear stress in MPa. Exactly where does this occur along the beam? ( 4 sigs) Your Answer:
8-46. The wide-flange beam is subjected to the loading shown. Determine the stress components at points A and B and show the results on a volume element at each of these points. 500 lb ↓ 2 ft 2 ft 2500 lb B 2 ft 4 ft 3000 lb 0.5 in.- Prob. 8-46 B 6 ft- 0.5 in. 1-4 in T 4 in. 12 in. 0.5 in.