An FM Broadcast receiver tunes from 88 MHz to 108 MHz. The IF is 10.7 MHz. The local oscillator uses a variable capacitor with a minimum value of 102 pF. Suppose the mixer uses high-side injection, what is the value of the inductor (in nH) so that the local oscillator will tune the receiver to the highest frequency on the band when the capacitor is minimum? Round off your answer to 2 decimal places.

An FM Broadcast receiver tunes from 88 MHz to 108 MHz. The IF is 10.7 MHz. The local oscillator uses a variable capacitor with a minimum value of 102 pF. Suppose the mixer uses high-side injection, what is the value of the inductor (in nH) so that the local oscillator will tune the receiver to the highest frequency on the band when the capacitor is minimum? Round off your answer to 2 decimal places.

Electricity for Refrigeration, Heating, and Air Conditioning (MindTap Course List)

10th Edition

ISBN:9781337399128

Author:Russell E. Smith

Publisher:Russell E. Smith

Chapter8: Basic Electric Motors

Section: Chapter Questions

Problem 25RQ: List the five capacitor replacement rules.

See similar textbooks

Similar questions

The figure below shows a phase shift oscillator with amplitude control. Design the circuit to produce 7kHz frequency and a ±8V output waveform. Assume that I1 = 1mA and R2=R3. Do your design on a piece of paper and then enter the various resistor and capacitor. NOTE: Use only E24 values for your design Enter the values of R1=_____Ω, R2_____kΩ . , R3._____kΩ , R4._____kΩ . , R5_____kΩ , R6_____kΩ and R7 _____kΩ and the value of C=_____ μF
A resistor of resistance R=1000 Q is maintained at 17 °C and it shunted by 100 µH inductor. Determine the rms noise voltage across the inductor over a frequency bandwidth of: Ans: 182 x109 volt i) ii) 15.9 kHz 159 kHz Ans: 9.22 x10-8 volt 111) 1590 kHz Ans: 2.34 x10-6 volt
Explain the working of 3 stage RC phase shift Oscillator. Design a 5 stage RC phase shift oscillator to generate a 300Hz sinusoid. Assume the capacitance used is 3pF
Using the circuit of below, preform transient analysis for the first pulse of V1 to predict the voltage across capacitor, C1 and plot the results. R1 1k V1 = 0 V2 = 15 TD = 0.010 TR = 0.00001 TF = 0.00001 PW = .05 PER = 0.2 V1 R2 C1 1k 10u
The carrier frequency is 500 Hz, and the modulating signal is a single-tone sinusoidal signal. The x-axis is in time while the y- axis is the amplitude of the AM signal. Determine the peak voltage level of the modulating signal in V. 3 2 1 -1 -2 -3 -5 0.005 0.01 0.015 0.02 0.025 0.03 0.035 0.04 0.045 0.05 Time (s)
please show work. i will give your work a thumbs up 7. Consider the oscilloscope screen shot below: ek Run 4.00p 1.0000 Vpp 0.000000 1. 5.000S/ IM points 500mV AFG Sine 100.00 Hz 0.00 V As shown the Volt / Div - 500mV per division, Time Base - 4.00 us per division, and Frequency is 100 KHz: a) Determine the peak-to-peak voltage (Vpp) and half-cycle average voltage (Vave). b) Determine the peak-voltage (Vpk) and root-mean-square voltage (Vrms). c) What is the period (T) of the IMHZ signal?
In a frequency modulating system, the frequency deviation constant k = 1 kHz/V. A sinusoidal modulating signal of amplitude is 15 V and a modulated frequency 3 kHz is applied. Calculate the peak frequency deviation Blank 1 kHz and modulation index.Blank 2 Blank 1 Add your answer Blank 2 Add your answer
An inductor is attached to an AC voltage source. Which change will result in a halving of the current?A. Halving the voltage and doubling the frequencyB. Doubling the frequencyC. Halving the frequencyD. Doubling the voltage and halving the frequency
an alternating current equation e=280 sin1256t what is the effective value of this signal a) 280 b) 560 c) 140 d) 395,92 e) 98,98 f) 197.96 g) 178.08
A step up chopper is used to feed a load at 400 V dc from a 250 V dc source. The inductor current is continuous. If the off time of switch is 20 microsec, the switching frequency of the chopper in kHz is ?
The pulse voltage waveform displayed on a CRO, is shown in figure given below. Find, (a) Frequency. (b) Magnitude of the pulse. (c) The amplitude. 21 0.5 5 0.2 10 20-(Vicm 5 ms 100 us 50 ms time/om 500 ms 30- 40 50 2s
Which of the the following statements concerning the phase angle compensator is true? A. It is a dc voltage source B. It is an ac voltage source with a controllable amplitude and uncontrollable phase angle C. It is an ac voltage source with a controllable amplitude and uncontrollable amplitude D.t is an ac voltage source with both a controllable amplitude and phase angle