An ion exchanger treats 1 MLD of water using an exchanger of capacity 100 kg/day/m3 with rate of flow being 0.5 m3/min/m2. Choose the correct statementsassuming total hardness of water equal to 84 mg/1 as Cao.Total hardness of water is equal to 150 mg/l as CaCO3.Correct OptionBSodium Alumino - Silicates may be used as ion-exchanger.Correct Optionlon exchanger can result in removing complete hardness.Correct OptionCorrect OptionThe height of ion exchanger required is 1.08 m if hardness of water is taken as 150 mg/1 as CacO3.

Answered: Image /qna-images/answer/cc82025c-4468-4bab-9513-e96ea09f1d7d.jpg

An ion exchanger treats 1 MLD of water using an exchanger of capacity 100 kg/day/m3 with rate of flow being 0.5 m3/min/m2. Choose the correct statements assuming total hardness of water equal to 84 mg/1 as Cao. Total hardness of water is equal to 150 mg/1 as CaCO3. Correct Option Sodium Alumino - Silicates may be used as ion-exchanger. Correct Option C lon exchanger can result in removing complete hardness. Correct Option Correct Option The height of ion exchanger required is 1.08 m if hardness of water is taken as 150 mg/1 as CaCco3.

An ion exchanger treats 1 MLD of water using an exchanger of capacity 100 kg/day/m3 with rate of flow being 0.5 m3/min/m2. Choose the correct statements assuming total hardness of water equal to 84 mg/1 as Cao. Total hardness of water is equal to 150 mg/1 as CaCO3. Correct Option Sodium Alumino - Silicates may be used as ion-exchanger. Correct Option C lon exchanger can result in removing complete hardness. Correct Option Correct Option The height of ion exchanger required is 1.08 m if hardness of water is taken as 150 mg/1 as CaCco3.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

..............Wh@t is the equivalent head of kerosene (s=.9) annd mercury( s=14.2). For a 4m head of water.......
Q2: Determine the resultant about the point O of the four forces and one couple which act on the plate shown in the Figure below. Note : for the resutant of 3osihys Forc es, You should computy the magnitude Kdirechion 30N 5 m- 3 ocos4s 25N 2 m 70 N-m 20N 40N o 30
Please choose the correct answer for each question: 1. Activity of a gas in equilibrium with solution is ______? A. its partial pressure; B.1.0; C. its molar concentration; D. 0.0 2. During a sorption procedure, the substance transferred from the gas or liquid phase to the solid phase is called ______ A. sorbent; B. sorbate; C. partition; D. none of the above 3. When a chemical has a lower KOW, it is more ______ A. hydrophobic; B. hydrophilic; C. more absorbable; D. less absorbable 4. _____ occurs on the adsorbent surface A. Adsorption; B. Sorption; C. Absorption; D. Adsorption and absorption 5. _____ addresses the change in the amount of a substance of interest with time. A. The equilibrium approach; B. The kinetic approach; C. Henry’s Law; D. Freudlich isotherm equation
A small lake with volume 10,000 m3 has a stream flowing into it with flow rate 100 m3/day and a Toluene concentration of 1.0 mg/m3. A factory discharges 5 m3/day into the lake with Toluene concentration of 10 mg/m3 – they want to increase effluent to 50 mg/m3. Toluene decays at a rate of 0.01/day. Assume steady-state and completely mixed (CSTR). a) How would this increase in discharge concentration change the lake concentration? b) Field studies show that the same lake would be better represented by dividing the lake into two cells. The first cell having a volume of 2,500 m3 and the second with 7,500 m3. How does this affect the estimate of concentration leaving the lake? Compare with one-cell model.Assume the factory continues to discharge at 10 mg/m3 into the first cell.c) Why does modeling the lake as multiple cells impact the final concentration leaving the lake? What do you expect might happen to the final concentration leaving the lake if we modeled it as more cells? How would…
(a) (ii) Following chemical species were reported for water sample from a well. Concentration (milli equivalent)/L 15 15 05 30 12 18 8.8 Species Chloride (CL) Sulphate (SO2-) Carbonate (CO2) Bicarbonte (HCO3) Calcium (Ca²+) Magnesium (Mg2+) pH Find (i) The total hardness (in mg/L) as CaCO3 (ii) Alkalinity present in the water (in mg/L) as CaCO3.
Aluminum pieces inadvertently collect on the filter. a. If left on the filter, will the percent yield of the alum be reported as too high or as too low? Explain. b. If the aluminum pieces are detected on the filter, what steps would be used to remedy the observation? Explain.
A Pump & Treat water treatment system at a contaminated site is designed to treat 5 m3/d of ground water in a reactor designed as a well mixed system. The effluent must meet quality standards of 25 mg/L of Iron. The treatment reactor’s 20 m3 volume is believed to be insufficient to achieve the standard. The ground water has an iron concentration of 100 mg/L and the treatment reactor has a kinetic constant of 0.5 d-1. – Confirm that the treatment system will NOT meet the effluent quality standards. – If not modify the design by adding a PFR system (using same treatment process and kinetics), what volume should the PFR addition be?
A small lake with volume 10,000 m3 has a stream flowing into it with flow rate 100 m3/day and a Toluene concentration of 1.0 mg/m3. A factory discharges 5 m3/ day into the lake with Toluene concentration of 10 mg/m3 - they want to increase effluent to 50 mg/m3. Toluene decays at a rate of 0.01 day-1. Assume steady-state and completely mixed (CSTR). a) How would this increase in discharge concentration change the lake concentration? Answer: 0.73 mg/m3 before, 1.71 mg/ m3 after b) Field studies show that the same lake would be better represented by dividing the lake into two cells. The first cell having a volume of 2,500m3 and the second with 7,500m3. How does this affect the estimate of concentration leaving the lake? Compare with one- cell model. Assume the factory continues to discharge at 10 mg/m3 into the first cell.
1-7. A water contains 200 mg/L Ca, 75 mg/L Mg, 180 mg/L HCO3, and 150 mg/L. CO₂, all expressed as CaCO3. Determine the chemical dosages required to soften this water as much as possible without removing magnesium. What will the final hardness be? 1-8. If the water of Prob. 11-7 is to be softened to a final hardness of 85 mg/L as CaCO, and is not to contain more than 25 mg/L. Mg as CaCO3, find the required chemical dosages. Solve 11-7
A liquid has a relative density of 0.8 and a kinematic viscosity of 2.3 centistoke. Deterimineits: (i) Weight density and (ii) Dynamic viscosity in Pa.sec 2:
Determine the pH of a solution that contains 2*(10^-4) mg/L of OH- (at 25 degrees).
During a steady flow process, the pressure of the working substance drops from 200 to 20 psia, the speed increases from 200 to 800 ft/s the internal energy decreases 20 BTU/lb and the specific volume increases from 2 to 10 ft³/lb. No heat transferred. Determine the following: a)AKE in ft-lb;/Ibm b)APE in ft-lb/lbm c)AW: (flow work) ft-lb:/lbm d)AH in BTU e) Net work in hp for 15 lb/min of fluid (use mass flow rate for this item only)