An object weighing 51kg is suspended from two ropes that are attached to the ceiling 1.5m apart. The other end of each rope is attached to a point on the top of the object. The ropes are 1.0m and 1.3m in length. Calculate the tension in each rope. Include a diagram.

An object weighing 51kg is suspended from two ropes that are attached to the ceiling 1.5m apart. The other end of each rope is attached to a point on the top of the object. The ropes are 1.0m and 1.3m in length. Calculate the tension in each rope. Include a diagram.

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter4: Coplanar Equilibrium Analysis

Section: Chapter Questions

Problem 4.43P: The vertical post is supported by two cables (the cable BFC runs over a smooth peg at F) and an...

See similar textbooks

Related questions

Q: At 0.5m/s, engine oil with a kinematic viscosity of 0.00024m2/s flows inside an annulus. A 3-in…

Q: Q3: The 10 kg slender bar is attached to the small roller A, which glides freely along the groove.…

A: Find the angular acceleration of the bar and the acceleration of the roller immediately after it is…

Q: Compute the Total work of a plant if the the combined cycle overall efficiency is the average value…

A: Combined cycle overall efficiency is the average value Heat input= 192 kJoules= 192000 Joules To…

Q: What will be the velocity of the follower at 90° using the following equation with segment angle…

Q: Two parallel shafts 1 & 2, 11 cm. apart and rotating at 75 RPM and 200 RPM are connected by…

Q: 10N A(2.3, 5) B(3,1.-2) D(-4, -2.0) C(4,0, 10) In the above, B, C, D are fixed and their coordinates…

A: Find the tension in cable AB, AC and AD.

Q: Determine the equivalent state of stress on an element at the same point which represents (a) the…

A: Givensig1=σy=-17MPasig2=σx=5MPash=τ=12MPa

Q: Completely determine the resultant of the forces shown in the figure. Option: R= 957lb down to the…

Q: (a) the smallest value of P required to start the block moving up the incline, (b) the corresponding…

Q: An insulated steel pipe carrying an oil having outside temperature of 90℉ and inside temperature of…

Q: process is

A: Given, Following are the process given for a TD process:Where, During a non-flow TD process (1-2)…

Q: available affordable safe custormer satisfaction

A: Explanation: 1) Power plant are mainly intended to produce power. 2) So in the process of producing…

Q: 1.) An ideal regenerative cycle is executed with 56700 kg/hr of steam initially at 13.44 MPa and 594…

Q: Multi-evaporator system with individual multiple expansion compressors and valves

A: ME-VCS (multi-evaporator vapour compression systems) are used to cool numerous zones. The…

Q: the value of B is

A: Given; Maximum value of W to avoid buckling of the beam isobtained as βπ2EI, where, πis the…

Q: A simplified heat utilization system of a Geothermal Power Plant provides the following data: Mass…

Q: centrifugal pump installation has been designed to discharge 0.126 m^3/s of brine (sp.gr. = 1.2).…

Q: A fountain consists of a horizontal inlet pipe with a cross-sectional area, A1, which enters a block…

Q: Required: Heat

Q: Seaside wind power generates total power of 418 KW with 12 wind turbine installed, what is the…

Q: R3 R2

Q: As shown in Figure 1 of the ski ramp, you need to make sure that the skier lands safe once they jump…

A: positive ax=0 , ay=-gapplying equation of motion along the…

Q: Determine the force in the members GF, CF, and CD of the truss, also indicate if the members are in…

A: As per our guidelines, we are supposed to answer only first three subparts in case of multiple…

Q: A wormgear set has a single-thread worm with a pitch diameter of 1.250 in, a diametral pitch of 10,…

Q: A steel rod (p-7860 kg/mUhas a length of 4.24 m. It is bolted at both ends between immobile…

Q: A perpetual motion machine is a machine that never stops, hence its name. It is a machine that can…

A: Concept: 1) First law of thermodynamics: It states that energy neither be created nor destroyed but…

Q: Calculate the moment of inertia of the shaded area about the x-axis. A

A: Triangle: Base, b= 45+45= 90 mm Height, h= 84 mm Semicircle: Radius, r= 28 mm

Q: principal stress on the surface

A: Given; Maximum principal stress on the surface which is at 450to the axis will have a value.Where…

Q: A STAR WHEEL ADJUSTER RETURN SPRINGS ANCHOR PLATE E ANCHOR PIN PLATE SPRING SPRING STAR WHEEL…

A: Backing plate - C Shoe - D Wheel cylinder - A

Q: A HSS tool is used to turn a steel workpart that is 300 mm long and 80 mm in diameter. The…

A: Answer: 1. Cutting speed for maximum production rate: 49.7746 m/min 2. Tool life in min of cutting:…

Q: SA5) What is the momentum of a vehicle if a force of 1000N is applied on it in 0.50 seconds if it…

A: Given Force, F = 1000 N Time taken, t = 0.5 sec Find Momentum, M

Q: Which of the following heat treatment

A: Given; Following are the heat treatment process used for surface hardening of steels: Where,Heat…

Q: G. Brake shoes Energy of motion H. Brake pads Operates the brakes on opposite comers of the vehicle…

A: Match Of the following ****As per company policy we are supposed to do only three subparts if you…

Q: A2.3-kg sphere S is being moved in a vertical plane by a robotic arm. When the angle e is 40°, the…

Q: 1) Given the pound(p) and eccentric(e), with a total area of 21 inch^2. What is the status of the…

A: Given that, Area of the cross-section, A=21 in2Load acting on the cube's top surface, P=28000…

Q: Given from a generator: Full-load rating of generator Full-load efficiency of generator : 90% Speed…

A: Since you have posted a question with multiple sub-parts, we will solve the first three subparts for…

Q: (Industrial safety) What is the concept of ALARP? Give an example of a situation where the ALARP…

A: Danger must be weighed against the trouble, effort, and money it will take to mitigate it. As a…

Q: Instructions: Identify the brake system components in the drawing. Place the identifying letter next…

Q: 4 Considor the sys bolow X (+) o force in put m Spring » k ? b daw por Uso fhe föllow ir netotim a…

A: Given : To find : Equation of motion Transfer function

Q: (1) (2) |(3) a (4) (5) В с b A, = mm? 159 A2 = A3 = 33 mm? A4 = As = 46 mm? 26.5 mm Y, = Y2 = y3 =…

Q: Calculate the Reynolds number, Re for water flow in a circular pipe. The diameter of the pipe is 50…

A: Reynold's Number is defined as the ratio of Inertia force to the viscous force in a flowing fluid.…

Q: Water at pressure p; flows through an underground cast iron pipe. The outer surface of the pipe is…

A: It is asked to find the suitable finite element idealization for a pipe of length 1000 m. The pipe…

Q: Choose "True" or "False" for the following: [1 1. The flow is assumed isentropic when it subjected…

A: A process is said to be reversible/Ideal in which system returns to its original state without…

Q: 2.) A power plant operating on a Rankine cycle has steam entering the turbine at 500 °C and 2 MPa.…

Q: The following data was collected in a road project: • Free haul distance = 50 meters Cost of borrow=…

Q: A jet-ski is moving on the water at a velocity of 12 fps with a bearing of S60°E. The current is…

A: Given data Jet ski is moving with a velocity of 12 fps with a bearing S60°E. The current is moving…

Q: 1. Knowing that at the instant shown the velocity of collar A is 900 mm/s to the left, determine (a)…

A: Given:- Velocity of collar A = -(900 mm/s) I To Find:- Angular velocity of rod ADB Velocity of…

Q: i need the answer quickly

A: For quarter circle, r= 150 mm X1 = 4r/3π =4×150/3π= 63.662 mm Y1 = 4r/3π =4×150/3π= 63.662 mm…

Q: 4. Through a refinery, fuel ethanol is flowing in a pipe at a velocity of 1 m/s and a pressure of…

Q: HoW 3. Determine the weightin newtons of awomen whose weight in pounds is 130. Also, find her mass…

A: Weight in newton , kg and slug from 130 pound.

Concept explainers

Buckling of columns

The column is described as a vertical member of the structure that carries an axial compressive load, and buckling is a lateral deformation of the column under the application of load.

Question

3. An object weighing 51kg is suspended from two ropes that are attached to the ceiling 1.5m apart. The
other end of each rope is attached to a point on the top of the object. The ropes are 1.0m and 1.3m in
length. Calculate the tension in each rope. Include a diagram.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 5 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The uniform 240-lb bar AB is held in the position shown by the cable AC. Compute the tension in the cable.
The cable supports three 400-lb loads as shown. If the maximum allowable tension in the cable is 900 lb, find the smallest possible sag hC at C.
The vertical post is supported by two cables (the cable BFC runs over a smooth peg at F) and an inclined surface. Compute the tension in the cables caused by the 1200Nm couple. Neglect the weight of the post.
The cable carrying three 400-lb loads has a sag at C of hC=14ft. Calculate the force in each segment of the cable.
The boom of the wall crane 4m long is held at right angles to the wall by a wire that is attached to the wall 3m above the foot of the boom. If the load lifted is 45000N, find the tension in the wire and the compression force in the boom. Neglect the weight of the boom. Draw a FBD
A uniform horizontal strut weighs 370.0 N. One end of the strut is attached to a hinged support at the wall, and the other end of the strut is attached to a sign that weighs 170.0 N. The strut is also supported by a cable attached between the end of the strut and the wall. Assume that the entire weight of the sign is attached at the very end of the strut. 30° Restaurant Find the tension in the cable (in N). Find the force (in N) at the hinge of the strut. (Give the direction in degrees counterclockwise from the +x-axis. Assume that the +x-axis is to the right.) magnitude direction °counterclockwise from the +x-axis
Physics for Engineering A uniform bar 3.00 m long is held by ropes at the ends making angle 60.0 and 30.0, respectively, with the horizontal. A weight of 200 N is hung 0.500 m from the left end where the 60.0 rope is attached. Find the tension in the ropes (T1 & T2) and the weight (W) of the bar. (Hint: Formulate three equations for the three unknowns, 2 equations for the 1st condition and 1 equation for the 2nd condition.)
A uniform bar 6 m long is held by ropes at the ends making angle 60° and 30°, respectively, with the horizontal. A weight of 400 N is hung 1.0 m from the left end where the 60° rope is attached. Find the tension in the rope and the weight of the bar.
2. Auniform bar 3.00 m long is held by ropes at the ends making angle 60.0° and 30.0°, respectively, with the horizontal. A weight of 200 N is hung 0.500 m from the left end where the 60.0° rope is attached. Find the tension in the ropes (T1 & T2) and the weight (W) of the bar. (Hint: Formulate three equations for the three unknowns, 2 equations for the 1st condition and 1 equation for the 2nd condition.) 3.00m T2 7 0.500m 60.0 B 200 N
The picture attached shows a boom that supports the weight 2000 N. The boom is supported by the hinge at A and a wire. It weighs 3000 N. Find the magnitude of the support force at the hinge.
A 400 N gas sign hangs from the end of a uniform strut BC. The strut is 4 m long and weighs 600 N. The strut is supported by a hinge at the wall at C and by a cable whose other end is tied to the wall at point A 3.0 m above the left end of the strut. Find the tension in the supporting cable and the force of the hinge on the strut. 5.0 m 3.0 m 4.0 m B GAS TAB= 1333 N TAB= 1167 N TAB= 400 N TAB= 1000 N leave the question 4 Other: Q 4 4 points Rc= 980 N O Rc= 360 N Rc= 890 N Rc= 1085 N O O O O O O O
The boom shown has a negligible weight and supports the 1000 N load. A 60° 1000 N 7.1 Find the tension in supporting cables between points A and B.