An orthogonal cutting operation is performed using a rake angle of 15°, chip thickness before the cut = 0.012 in and width of cut = 0.100 in. The chip thickness ratio is measured after the cut to be 0.55. Determine (a) the chip thickness after the cut, (b) shear angle, (c) friction angle, (d) coefficient of friction, and (e) shear strain.

An orthogonal cutting operation is performed using a rake angle of 15°, chip thickness before the cut = 0.012 in and width of cut = 0.100 in. The chip thickness ratio is measured after the cut to be 0.55. Determine (a) the chip thickness after the cut, (b) shear angle, (c) friction angle, (d) coefficient of friction, and (e) shear strain.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The following data was obtained from an orthogonal cutting test. Rake angle = 20° Depth of cut = 6 mm Feed rate = 0.25 mm/rev Cutting speed = 0.6 m/s Chip length before cutting = 29.4 mm Vertical cutting force = 1050 N Horizontal cutting force = 630 N Chip length after cutting = 12.9 mm Using Merchant's analysis, calculate (a) Magnitude of resultant force, (b) shear plane angle, (c) friction force and friction angle, and (d) various energies consumed.
Note: Read the question carefully and give me right solutions according to the question. In orthogonal cutting of steel tube of 150 mm diameter and 2 mm thick, the cutting force was 130 kg and feed force was 35 kg for chip thickness of 0.3mm. The orthogonal cut was taken at 60 meter per minute with a feed of 0.14 mm/rev. If the back rack angle of the cutting tool was - 8 o (minus 8 degree), then calculate the shear strain and strain energy per unit volume.
During orthogonal cutting operation of material has shear strength 95.5 Mpa. The cutting force is more than thrust force by 10%. The rake angle = 5°, the width of the cut = 5.0 mm, the chip thickness before the cut = 0.6, and the chip thickness ratio = 0.38. Determine (a) both cutting force and thrust force and (b) the coefficient of friction in the operation.
Rake angle=20 degree, Depth of cut=6 mm, Feed rate =0.25mm/rev,Cutting speed=0.6 m/s, chip length before cutting=29.4mm, vertical cutting force= 1050 NHorizontal cutting force=630, chip length after cutting=12.9Using Merchant’s analysis calculate(a) direction and magnitude of resultant force(b) friction force and friction angle(c) shear plane angle
2. The following data was obtained from an orthogonal cutting test: Rake angle = 20° Cutting speed = 100 m/min Chip length before cutting = 29.4 mm Chip length after cutting = 12.9 mm Vertical cutting force 1050 N Horizontal cutting force = 630 N Using Merchant's analysis, calculate (a) resultant force (c) friction force and friction angle (b) shear plane angle (d) total work done
3) The following data are available from orthogonal cutting experiment, Depth of cut t, = 0.13 mm, width of cut w = 2.5 mm, rake angle a = -5°, cutting speed v = 2 m/s, Chip thickness, t= 0.23 mm, cutting force, F. = 430 N, thrust force, F = 280 N. Determine the following: Shear angle Friction Coefficient u (using F= µ N) Shear Stress t,S Shear strain y on the shear plane. Power required to perform the operation. Gross power required if the efficiency of the machine is 85%. Specific Energy, Ut
A turning operation is made with a rake angle of 10 degrees, a feed of 0.010 in/rev, and a depth of cut = 0.100 in. The shear strength of the work material is known to be 50,000 lb/in2, and the chip thickness ratio after the cut = 0.40. Determine the cutting force and the thrust force. Use the orthogonal cutting model as an approximation of the turning process.
2) In an orthogonal cutting operation, the cutting tool has a rake angle = 20°. The chip thickness before the cut = 0.25 mm. If the cutting force and thrust force are measured during an orthogonal cutting operation with values, Fc = 1450 N and Ft = 1990 N. The width of the orthogonal cutting operation w = 2.5 mm. the friction angle B is = 79.91° Determine: The Shear Angle The Shear Strain The Shear Strength of the material The Force of Friction
Low carbon steel having a tensile strength of 450 MPa and a shear strength of 270 MPa is cut in a turning operation with a cutting speed of 2500 mm/s. The feed is 0.15 mm/rev, and the depth of cut is 0.25 cm. The rake angle of the tool is 12° in the direction of chip flow. The resulting chip ratio is 0.55. Using the orthogonal model as an approximation of turning, determine (a) the shear plane angle, (b) shear force, (c) cutting force and feed force.
Question 4. The following data are available from orthogonal cutting experiments. The depth of cut (feed) to = 0.13 mm, width of cut b = 2.5 mm, rake angle a = - 5°, and cutting speed V = 2 m/s. Chip thickness, t. (mm) = 0.23 Cutting force, F. (N) = 430 Thrust force, F; (N) = 280 Determine the shear angle ð, friction coefficient u , shear stress t, shear strain y on the shear plane, chip velocity Ve, and shear velocity Vs, as well as energies uf ,Ug, and u
In orthogonal cutting, the depth of cut is 0.5 mm at a cutting speed of 2 m/s. If the chip thickness is 0.75 mm, the chip velocity is а. 1.2 b. 1.67 1.33 d. 1.44 оо
A student is using a lathe with 80-hp and 80% efficiency to fabricate a copper alloy with Sy = 1200ksi If the width of cut is 0.30 inand the student set a rake angle of 0and a cutting speed of 200fl / min while she assumed a coefficient of friction to be 0.5. What is the maximum depth of cut the student can achieve?