An overhang beam carries a concentrated load, triangular load and uniformly distributed load as shown in the figure. UsingArea Moment Method, Solve the following unknowns.Let w = 134kN/m, a = 1.2m, b = 3m.NOTE: WRONG SIGN IS WRONG. WRONG UNITS IS WRONG.2P5PABbIf the moment at the roller support is equal to -1410kN-m, determine the value of "P".Draw your reference line at the leftmost part of the beam and determine the sum of all positive areas of moment diagrams.(Note: don't put units)Draw your reference line at the leftmost part of the beam and determine the sum of all negative areas of moment diagrams.(Note: don't put units)

Solution: Given Data: w=134 kN/ma=1.2 mb=3 mmoment at roller B MB=-1410 kN.m

Answered: An overhang beam carries a concentrated…

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A simply supported beam ABC is loaded at the end of a bracket BDE (see figure). D (Use the deformation sign convention. When entering expressions, use the following as necessary: P and L.) Draw the axial-force diagram for ABC. N N State expressions for the minimum and maximum values of the axial force Mx). Nain = max Draw the shear-force diagram for ABC. Vrur 00 State expressions for the minimum and maximum values of the shear force Vx). min V = max Draw the bending-moment diagram for ABC. M M OMeen O OMin State expressions for the minimum and maximum values of the bending moment M(x). Mmin = %3D 'max
Problem #2 A wood beam with a square cross section supports the load as shown. Determine the cross sectional dimension in millimeter if the allowable flexure stress is 1000 KPa. Use double integration method. Note: Maximum moment occur at support. 100N/m 100N 1m 4
A beam is loaded and supported as shown. (a) Use the double-integration method to determine the reactions at supports A and C. (b) Draw the shear-force and bending-moment diagrams for the beam. Assume w = 16 kN/m, L = 14.0m and El - 5.5x 104 kN-m? is constant for the beam. %3D A -L/2- Part 1 Cut a cross-section through the beam between points A and B, and draw a free body diagram to the left of the cut. Determine an expression for M(x) in section AB of the beam. Check your expression by calculating Mat x-3,5 m. M(x) A Answer: M(x) - kN-m + mA, eTextbook and Media
4. A rigid beam fixed at O is loaded by an nth degree spandrel having a vertex at B. а. Determine the shear functions. Use the fixed end as the origin and set rightward and upward as positive directions. Express your answers as V(x)={shear expression} without simplifying {shear expression}. Show all FBDS used b. Draw the shear diagram Draw the moment diagram d. If the magnitude of the maximum moment is 20.25kNm, determine the degree of n. С. Зт B 3m A +x kN 5- n° m
4. A rigid beam fixed at O is loaded by an nth degree spandrel having a vertex at B. a. Determine the shear functions. Use the fixed end as the origin and set rightward and upward as positive directions. Express your answers as V(x)={shear expression} without simplifying {shear expression}. Show all FBDS used b. Draw the shear diagram c. Draw the moment diagram d. If the magnitude of the maximum moment is 20.25kNm, determine the degree of n. 3m 3m A B +x kN 5 no m
Problem 1 A simply supported prismatic beam AB carries a uniformly distributed load w per unit length. Determine: d¹y (a) Start with the EI=-w and integrate it twice to ,d²y dx4 get to El= M(x)=?. Show what? is. dx² a. Hint: What is the moment at both ends? (b) Derive the Moment equation and does it match the solution you got for (a) (c) Equation of the elastic curve in variables by integrating your solution for (a) twice more and solving for the last two constants of integration. (d) The maximum deflection of the beam in variables W Answer: (a) y = 24 (−x¹ + 2Lx² − Ľ³x) (b) \y\max 24EI B 5wL4 38EI
Please solve using 3 kip instead of 2 kip for the downward force 2 kip at P a 60° 1 kip The end of a cantilever I beam supports forces from three cables. a) If P = 0, determine the resultant force applied by the two cables to the I beam and report your result using polar vector representation. b) Repeat Part (a) if P = 1.5 kip and ? = 30?. c) With ? = 30?, what value of P will produce a resultant force that is horizontal? d) If the resultant force is to be horizontal and Pis to be as small as possible, determine the value ? should have and the corresponding value of P.
USE AREA MOMENT METHOD TO SOLVE THIS PLEASE. THANK YOU. SHOW COMPLETE SOLUTION. The trapezoidal loading is carried by the simply supported beam AB. The beam is a steel tube with the cross section shown. Determine the displacement of the beam at midspan and the slope angle of the elastic curve at end A. Use E = 200 GPa for steel. 30 kN/m 15 KN/m 80 mm, 3m 70 mm
.. The continuous beam is loaded as shown in the figure. A is a fixed support, while B and C are roller. Assume that supports do notsettle, and El is constant. Using the consistent deformation method determine the following: a. Reactions at the supports. b. Sketch the shear and moment diagram of the beam. c. Determine the value and location of maximum shear and bending moment of the beam. A Sm 50 kN 5m 15 kN/m B 10m 60 kN Im D
A steel beam is of cross section of right triangle of dimension 40 mm wide and 60 mm wide and 60 mm depth having yield point stress f, = 280 N/mm?. Evaluate the fully plastic moment for the condition that the neutral axis passes through point B as shown in the figure below and divides the right triangle into two equal triangular parts. Assume that the plane of the load passes through the centroids of two triangles thus created. 40 mm A. 60 mm
The beam ABC is subjected to a point load at the middle of segment AB and a uniformly distributed load at the segment BC, as shown in the figure. A 20 N Set Wo B 1.5W, N/m Figure 1: Overhang beam Find the equation of the elastic curve for the segment AB. L C - 3 N/m, L = 2 m, EI = 25000 Nm². Use the method of superposition for all parts. Hint: for x > L/2 in segment AB, the solution can be obtained from the table by replacing x by L-x.
Calculate the vertical component of the internal force at B. Let W = 2 kips/ft. and P = 22 Note: 1. Answer in whole number 2. Indicate the Minus sign (-) if answer is negative. For positive answer "no need" to write the (+) sign. P- 9'- B W 10' C D 12'

SEE MORE QUESTIONS

Recommended textbooks for you

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Fundamentals of Structural Analysis

Civil Engineering

ISBN:

9780073398006

Author:

Kenneth M. Leet Emeritus, Chia-Ming Uang, Joel Lanning

Publisher:

McGraw-Hill Education

Sustainable Energy

Civil Engineering

ISBN:

9781337551663

Author:

DUNLAP, Richard A.

Publisher:

Cengage,

Traffic and Highway Engineering

Civil Engineering

ISBN:

9781305156241

Author:

Garber, Nicholas J.

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS

An overhang beam carries a concentrated load, triangular load and uniformly distributed load as shown in the figure. Using Area Moment Method, Solve the following unknowns. Let w = 134KN/m, a = 1.2m, b = 3m. NOTE: WRONG SIGN IS WRONG. WRONG UNITS IS WRONG.