An unbalanced delta-connected load is connected across the lines of a 4-wire balanced three-phase supply with neutral connection. Two wattmeter W1, W2 are connected in lines 1 and 3 with the common potential connection in the neutral wire. These wattmeters read 1796.5 and 3000 watts, respectively. The current in lines 1 and 3 is 20 A. If the common potential connection is transferred to line 2, what will be the reading of the two wattmeters? The system voltage per phase is 208 V. Assume a phase sequence of 1-2-3 with Vin as reference.

An unbalanced delta-connected load is connected across the lines of a 4-wire balanced three-phase supply with neutral connection. Two wattmeter W1, W2 are connected in lines 1 and 3 with the common potential connection in the neutral wire. These wattmeters read 1796.5 and 3000 watts, respectively. The current in lines 1 and 3 is 20 A. If the common potential connection is transferred to line 2, what will be the reading of the two wattmeters? The system voltage per phase is 208 V. Assume a phase sequence of 1-2-3 with Vin as reference.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

An unbalanced delta-connected load is connected across the lines of a 4-wire balanced three-phase supply with neutral connection. Two wattmeter W1, W2 are connected in lines 1 and 3 with the common potential connection in the neutral wire. These wattmeters read 1796.5 and 3000 watts, respectively. The current in lines 1 and 3 is 20 A. If the common potential connection is transferred to line 2, what will be the reading of the two wattmeters? The system voltage per phase is 208 V. Assume a phase sequence of 1-2-3 with V1n as reference. ...
a wye connected load as 480v applied to it what is the volatage drop across each phase?
17 In the figure shown, the voltage V1 the voltage V2 by V₁ * out of phase. 40)
Simple summary about the measurement of power in a 3 Phase AC circuit using a two-wattmeter. Explain the relationships between ammeter, wattmeter, and total power.
In three phase power each voltage current and power is delivered by how many degrees..
In a 3-phase power measurement by two wattmeter method the reading of one of the wattmeter is zero. The power factor of the load must be a. 0.3 b. Zero c. Unity d. 0.5
Why will a 3phase Delta connected load yield more power compared to connecting it in Wye to the same line? Also how much more power is generated when connected i n Delta compared to Wye?
A wye-connected load has a voltage of 480 V applied to it. What is the voltage drop across each phase?
Question No.33 A single phase half bridge VSI has load R = 1.8 Q and DC source voltage 130 – 0 – 130 V. Find the power delivered to the load due to fundamental current.
A single phase two wire a.c. Find the percentage saving in feeder copper if the system voltage is increased from 440 V to 1100 V. Assume same power is transmitted in both, same power loss and same power factor in both. I₁ I₁ 440V (a) 12 1100V 12 (b)
Voltage and current of a three – phase load are as follows: Voltage: 3.6 kV, 8 degrees Current: 37 A, 45 degrees What is the power factor of this load?
I. Va 240V XL1 XL3 VE 4800 ohm Ve 4800 ohm 240V 240V XL2 4800 ohm Figure 1 b) Using the block diagram in Figure 2, draw the connection for measuring the line current of each phase in Figure 1. AMMETER CAPACITIVE LOAD o 0o 0 * 025A 15A * 025A 1.5A * 0.25A 15A 4.8ka 2.4k 1.2k 4.8kΩ 2.4kΩ 1.2) 48 2.4 1.2kΩ RESISTIVE LOAD POWER SUPPLY WATTMETER / VARMETER 240/415 V 3A L1 L2 O L3 L1 12 L3 L1 12 L3 N 4.8Ω 2.4k 1.2kΩ 4.8kΩ 2.4kΩ 1.20 48 2.4Ο 1.2Ω VOLTMETER INDUCTIVE LOAD COM 250v sOOV COM 25OV 50ov COM 250V 500y 4.8kn 2.4kN 1.2kn 4. kΩ 24kΩ 1.2 4.8 24kΩ 1.2kΩ Figure 2 O 0000