Application Problem. A battery pack consisting of n 12V voltage cells connected in par- allel is shown in Figure 1.144. This battery pack is to provide a load current IL of at least 11.5A to the 12 load resistor RL as shown. Assuming that all voltage cells are identical with an open circuit voltage Ei of 12V and an internal resistance Ri of 0.32, calculate the number of cells n needed to provide a minimum of 11.5A to RL; that is, L 211.5A. battery pack R10 E, E = 12V R= 0.30

Application Problem. A battery pack consisting of n 12V voltage cells connected in par- allel is shown in Figure 1.144. This battery pack is to provide a load current IL of at least 11.5A to the 12 load resistor RL as shown. Assuming that all voltage cells are identical with an open circuit voltage Ei of 12V and an internal resistance Ri of 0.32, calculate the number of cells n needed to provide a minimum of 11.5A to RL; that is, L 211.5A. battery pack R10 E, E = 12V R= 0.30

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Power supply circuit is delivering 0.5 A and an average voltage 20 V to the load as shown in the circuit below. The ripple voltage of the half wave rectifier is 0.5 V and the diode is represented using constant voltage model. The smoothing capacitor value is equal to 220V omsh RL VI-DC20V 0.01 F 0.02 F 0.0167 F None of the above
Power supply circuit is delivering 0.5 A and an average voltage 20 V to the load as shown in the circuit below. The ripple voltage of the half wave rectifier is 0.5 V and the diode is represented using constant voltage model. The smoothing capacitor value is equal to IL-DC =0:5A RL VL-DC =20V 220V omsb O 001 F O 0.02 F O 0.0167F O None of the above Activate
5 For the following circuit: a) Draw a table to mention the names, the states (ON/OFF) and turn on voltages for all the diodes of the circuit. (V = 3.5V for D3) and draw the equivalent circuit. b) Find the voltage across R1, R2, R3 c) Find the current through D1 , Dz , D3 and D4 D1 Si R2 D2 5002 Si R1 7502 R3 D3 D4 V1 1kn Blue GaAs 10v
A half-wave rectifier is needed to supply 15-V dc to a load that draws an average current of 250 mA. The peak-to-peak ripple is required to be 0.2 V or less. What is the minimum value allowed for the smoothing capacitance?
a. If you do not go completely around the loop when applying Kirchhoff’s voltage law, then the algebraic sum of the voltages cannot be determined the algebraic sum of the voltages will always be positive the algebraic sum of the voltages will always be negative the algebraic sum is the voltage between the start and finish points b. A p -type semiconductor is a semiconductor doped with impurity atoms whose electron valence is +4 pentavalent impurity atoms trivalent impurity atoms
Which of the following circuit elements is a typical example of semiconductor material? Lütfen birini seçin: O A. Capacitor O B. Inductor O C. Resistor O D. npn BJT O E. Voltage source
Q3: For the circuit below determine: 1. Name of the cet. 2. Determine and draw (Vo), also its dc - level. (all diodes are Si) D2 D1 20 Vo w. -20 D3 D4
Consider the following circuit: VI R₁ = 4kQ2 IDI R₂ = 8 ΚΩ D₁ ID2 R3 = 6 ΚΩ D2 ID3 + 1.0 V - VO R4= 4 ΚΩ D3 + 2.0 V Figure 1: Diode circuit for the Question Please find Ip1, ID2, IDs and to using constant voltage drop model for diodes. UF 0.7 V. v1 = 3V.
for the circuit shown in the figure, plot the output voltage waveform and present the resolution in sections considering that the diodes are silicon. D4 23 100k D6 100k 24 DIODE SV Vs4 [v] 20 Vo -20
5. For the circuit in the figure, what should be the value of R2 so that the current passing through the silicon diode (which has Vd= 0.67 Volts) is 250uA
Q3) For the circuit in figure(2) find the current and the voltage for (1k Ohm, 2k Ohm, 3k Ohm) and the voltage on each diode where each diodes are Ge-type: D1 D4 1k Ohm D2 D5 -21 V 2k Ohm D6 -14 V 12V 3k Ohm
Q2: Draw the output waveform for the three shown circuits. 1- +10V D V. 0- 5 V 5 V -10V Diodes are IN914 2- Assume Vm=20V, show the Vdc on the graph R Ds 3- Assume Vm=18V and V=5V. 34