Assume an annual available energy of 1200 Kwh/m2. The system rating peak is 50 Kw. The annual energy yield is 51000 Kwh. Find kwh 1) The Final yield Y [- Kw 2) The Performance ratio [%] 3) Given the Monthly values of final yield (Yf), reference yield (YR), and array yield (YA for one year, plot the monthly Performance ratio in percent for the whole year. YF YR YA 8.00

Assume an annual available energy of 1200 Kwh/m2. The system rating peak is 50 Kw. The annual energy yield is 51000 Kwh. Find kwh 1) The Final yield Y [- Kw 2) The Performance ratio [%] 3) Given the Monthly values of final yield (Yf), reference yield (YR), and array yield (YA for one year, plot the monthly Performance ratio in percent for the whole year. YF YR YA 8.00

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

(a) What is the frequency in Hertz and rad/s of the voltage waveform shown on Figure Q1? (b) Calculate the average voltage and rms ac voltage of the waveform shown on Figure Q1. (c) Calculate the total rms voltage of the waveform shown on Figure Q1. (d) The voltage on Figure Q1 is connected across a 0.15 2 resistive load. Calculate the power dissipated in this resistor.
chapter 1 Q1 The rms value the AC input voltage to the of Circuit shown is 230U, and the firing angle is maintained Current is 5 A. constant at 45° so that the load a) Calculate the de output voltage. b) Assume that the load resistance remains the a same, find the current is a FWD is used at the output. c) If^ prime prime ScR^ prime prime " is open circuited, find load voltage and current a is the Same) (FWD is still connected and high. "L Load Ans[146.4U,6.03A ; 3.c2A] 3 3 FWD
Q.1) A single phase load consisting of 5 2 in series with an inductance of 0.02297 H is operated in a phase control mode with a of 90°. The source is 240 V RMS, 60HZ. Find: a) Draw the waveform of VTI and VR. b) Find the conduction angle (6). c) Calculate the RMS value of load current. d) Find the power factor e) What is the minimum value of a for which phase control is in effet. f) Find the size of the first three terms in the Fourier series for the current. T Zoom
Another name for the RMS value of current or voltage is ... O the effective value O the exact value O the true value O the reactance value
Q1/ A feeder with reactance of j0.2 pu has a Vs = 1.2pu. If QR = 0.3pu then approximate voltage drop in feeder will be ...... pu.
A full wave ac voltage controller with 25 Ω resistive load is shown in the figure; It is desired that the load receive an effective current of 9.6 Arms; if the input voltage is Vm = 440 V, calculate:a) The firing angle of each SCR to have a symmetrical output voltage wave.b) the rms output power.c) The apparent power of the source.d) The rms current of each SCR.e) The average current of each SCR. Please answer all subpart either dislike is ready..
derive the RMS formula for the following a.) b.)
A site with an average wind velocity of 9 m/s is to be designed using wind turbine as energy source. What is the potential power available in the wind if a 2 meter wind turbine will be installed?
Calculate for the value of VL(peak). Please show your complete solution. Thank you.
Define the concept of "harmonic distortion" in power systems. What are the sources of harmonics, and how do they affect the quality of electrical power?
Q1. following: For the circuit shown in figure (a). Let V1 = 10Vms, frequency 10KHZ. Draw the A. Impedance diagram. B. Voltages phasor diagram. C. Current phasor diagram. D. Measure the voltage across R1,R2, Vin, and the inductor using the ocillscope using PROTEUS software. E. Measure the voltage in R1, R2, and the inductor using DMMby using PROTEUS software. F. From the above measurments verify your result. R2 1K V1 VSINE R1 L1 2K 1000M
A series circuit consisting of a 50 – ohm resistor, 0.5 – henry inductor, and a 100 – microfarad capacitor is connected to a 110 – volt, 50 cycle source. Calculate the following: a.) TOTAL IMPEDANCE b.) CURRENT c.) VOLTAGE DROP ACROSS THE RESISTOR d.) VOLTAGE DROP ACROSS THE INDUCTOR e.) VOLTAGE DROP ACROSS THE CAPACITOR f.) AVERAGE POWER g.) APPARENT POWER h.) REACTIVE POWER i.) POWER FACTOR j.) POWER FACTOR ANGLE DRAW THE PHASOR DIAGRAM IF POSSIBLE AND ROUND OFF TO FOUR DECIMAL PLACES