Assume that the op amp in the circuit in Fig. 2.1.1 is ideal. Find the currents through all branches and determine the voltages at all nodes. Do your anal- ysis and show your results directly on the circuit diagram. You will find that the op amp supplies a current larger than that drawn from the 1-V source connected to the input. Where does the additional current come from?

Assume that the op amp in the circuit in Fig. 2.1.1 is ideal. Find the currents through all branches and determine the voltages at all nodes. Do your anal- ysis and show your results directly on the circuit diagram. You will find that the op amp supplies a current larger than that drawn from the 1-V source connected to the input. Where does the additional current come from?

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter18: Resistive-inductive Parallel Circuits

Section: Chapter Questions

Problem 13PP: In an R-L parallel circuit, IT=1.25 amps, R=1.2k, and XL=1k. Find IR

See similar textbooks

Similar questions

Vin R 1₁ www www- R 1₂ R wwwwwwww + Vo If the non-inverting terminal of the op-amp in the figure is grounded find Vo/Vin. Show details of your work.
E) For the op-Amp circuit shown, find the output V.. 2K 2VoWWW 2K 4VoWWW 6V o 2K a 2K
4kΩ 5k2 3mA . 3ΚΩ 2k2 1kN Determine for the above ideal op-amp circuit, Vo, lo, and the power dissipated in the 2kn resistor. You may assume that the op-amp is ideal and always operates in the linear region.
The op amp in the circuit in the figure is ideal. The dc signal source has a value of 840 mV. Part A Find the Thévenin voltage of the equivalent circuit with respect to the output terminals a, b. Express your answer with the appropriate units. ANSWER: VTh= RTh= Part C What is the output resistance of the inverting amplifier? Express your answer with the appropriate units. ANSWER: V Th Part B Find the Thévenin resistance of the equivalent circuit with respect to the output terminals a, b. Express your answer with the appropriate units. ANSWER: Ro= 1.6 ΚΩ www + 24 ΚΩ ww + 15 V -15 V RTh Va a b
Note: assume ideal op-amp behaviors for Problems 1-4. Which of the following op-amp circuits can be considered to have negative feedback. For those that have negative feedback, write down Viny and Vout. You may assume the op-amps are powered by +9V. a) Vin c) Vin +1.2V Vout Vout b) d) Vin Vin wim с A +1.2V V out Vout
Example:. Find A (cl)? V₁ 10 B wlli Op-amp m 7 to V₂
Q1) Using the following input waveform shown in Figure 1, sketch the corresponding output waveform for each op amp circuit shown in Figure 1(a through d). Assume ideal op amp behavior. 30 441 wwwww 25 AG 10 pF 100 k www (6) 1,0 330 www 10 LQ www 51.02 540 M 530 www 10 KO or
In this circuit nown, use an ideal op amp model to gat the exprasion for the gain, R V. = f(R,Ar) R-Ar
(b) Draw an amplifier circuit using an ideal op-amp that computes the average of 3 input signals. State clearly the value of the resistances given that the inputs are Vi = 5 V, V2= 3 V and V3 = 1 V and the output is Vout = -3 V.
From Figure 3, write node-voltage equations: one for each input a. terminal of the op amp. b. The expression for the load current (i.) can be written as a function of the input voltage (V) and the load voltage (v.) iz = Avin + Bv, b.1. What is the expression for A? What should be the condition for R, R, R, and R4, so that B is b.2. zero? (NB: this condition will make i, depend only on v, and not on R.) R4 R3 OA1 R2 R1 RL Vin VL iL Figure 3
2K The op amp used in the inverting amplifier circuit is not ideal. In fact, it is an LM741 with the following parameters: v W Rin = 2 MQ, AoL = 200 V/mV, Rout = 200 Q. Determine the gain vo/vi of the op amp circuit. If the gain computed in a is the actual gain, what is the percentage accuracy of the computed gain if the op amp is considered ideal? 4. 1K vo а. b.
For this op amp, an equation needs to be made for V0 = Va + Vb. I thought it was -4(Va) + 4(Vb) as the difference, but that doesn't seem to be correct. The voltage limits for the output voltage are -0.8 V less than or equal to Vo less than or equal to 3.2 V. Can you show how to set up the equation for V0?