Based in the given PV diagram, what is the work done on the gas in the process shown, in Joules? Your answer needs to have 2 significant figures, including the negative sign in your answer if needed. Do not include the positive sign if the answer is positive. No unit is needed in your answer, it is already given in the question statement. p (kPa)

Based in the given PV diagram, what is the work done on the gas in the process shown, in Joules? Your answer needs to have 2 significant figures, including the negative sign in your answer if needed. Do not include the positive sign if the answer is positive. No unit is needed in your answer, it is already given in the question statement. p (kPa)

Physics for Scientists and Engineers: Foundations and Connections

1st Edition

ISBN:9781133939146

Author:Katz, Debora M.

Publisher:Katz, Debora M.

Chapter20: Kinetic Theory Of Gases

Section: Chapter Questions

Problem 42PQ

See similar textbooks

Similar questions

The temperature at state A is 20°C, that is 293 K. What is the heat (Q) for process D to B, in MJ (MegaJoules)? (Hint: What is the change in thermal energy and work done by the gas for this process?) Your answer needs to have 2 significant figures, including the negative sign in your answer if needed. Do not include the positive sign if the answer is positive. No unit is needed in your answer, it is already given in the question statement. p (atm) 4 3 2 -> +V (m) 5
A container holds 102.9 liters of Oxygen at 268.4K and a pressure of 1.95 atmospheres. How much heat is required to raise the temperature of this gas to 314.1K, holding the volume constant? Give your answer in kJ. Treat the gas as an ideal gas. Note: It is understood that your answer is in units of kilo-Joules, however do not explicitly include units in your answer. Enter only a number. If you do enter a unit ("kJ" in this case), you answer will be counted wrong.
Pump some air into the container and hold the volume constant.Heat the gas using the heater under the container. temperature(K) pressure(kPa) 400 800 500 1000 600 1200 700 1400 800 1600 900 1800 1)Plot a graph of Pressure vs temperature and attached the graph below (show the data points and label the axes) 2)find the “molar density” of the gas in the container. (unit of answer: mole/m3)(Hint: consider the ideal gas law , the graph should be ??=??? a straight line, you can use the slope of the graph to find the answer. Pay attention to the unit. R=ideal gas constant=8.314 JK-1mol-1=8.314 m3PaK-1mol-1) Include the appropriate units in the physical quantities.(with steps)
QUESTION 25 The temperature at state A is 20°C, that is 293 K. What is the heat (Q) for process A to D, in MJ (MegaJoules)? (Hint: What is the change in thermal energy and work done by the gas for this process?) Your answer needs to have 2 significant figures, including the negative sign in your answer if needed. Do not include the positive sign if the answer is positive. No unit is needed in your answer, it is already given in the question statement. p (atm) 5 4 3 2 1 O A D 1 1 2 3 4 B I 5 → V (m³)
A person consumes about 2700 Cal a day. 1 Cal = 4186 J, and 1 kWh = 860 Cal. Part A What is this energy in joules? (2 sig figs) Part B What is this energy in kilowatt-hours? (2 sig figs) Part C If a power company charges about 10 ¢ per kilowatt-hour, how much would this energy cost per day if the person bought it from the power company? (2 sig figs)
Topic: Thermodynamic Measurements and Quantities 2.) 5. An Olympic-size pool is 50.0 m long and 25.0 m wide. How many gallons of water (density = 1.0 g/mL) is needed to fill the pool to an average depth of 4.8 ft?
A 20-ton vapor compression refrigeration system is to evaporate R-12 at -20°C and to condense it at 40°C. The vertical compressor is to run at 10000 rpm; it is single acting, has the bore equal to the stroke, and has 5% clearance. Vapor enters the compressor at -10°C and liquid enters the expansion valve at 30°C. Draw the schematic and ts diagram 1.1 What refrigeration flow rate is required?1.2 What would be the bore and stroke of the compressor?1.3 What power is required by the compressor?1.4 What is the quantity of the cooling water required in the condenser for a 8-degree increase in temperature?
Consider a pressure versus volume graph, where the different curves represent different processes done on a gas. Starting at the origin to point 1, the pressure and volume are increased to 2913 Pa and 4.25 m³, respectively. From 1 to 2, the gas expands at constant pressure to a volume of 7.25 m³. From 2 to 3, the pressure rises to 4082 Pa. Finally, from 3 to 4, the gas expands again to 10.85 m³. Rank the curves from the most positive to the most negative amount of work done on the gas. Pressure (Pa) 0 1 3 2 Volume (m³) What is the total work done on the gas? 4 Wo-4 = Most positive work Incorrect 29624.325 23 0 → 1 1 → 2 3→ 4 Most negative work Answer Bank
An arctic weather balloon is filled with 1.56L of helium gas inside a prep shed. The temperature inside the shed is 11.°C. The balloon is then taken outside, where the temperature is 2.°C. Calculate the new volume of the balloon.You may assume the pressure on the balloon stays constant at exactly 1atm. Round your answer to 3 significant digits.
A cylinder is filled with10.0Lof gas and a piston is put into it. The initial pressure of the gas is measured to be 268.kPa.The piston is now pushed down, compressing the gas, until the gas has a final volume of 8.70L. Calculate the final pressure of the gas. Round your answer to 3 significant digits.
-80J of work are done on the gas in the process shown in (Figure 1). Figure p (kPa) P₁- 0 0 100 200 300 1 of 1 V (cm³) Part A What is p₁ in kPa? Express your answer in kilopascals. P1 = Submit IVE ΑΣΦ Provide Feedback Previous Answers Request Answer ? kPa
The temperature at state A is 20ºC, that is 293 K, what is the temperature at state D, in Kevin? Your answer needs to have 2 significant figures, including the negative sign in your answer if needed. Do not include the positive sign if the answer is positive. No unit is needed in your answer, it is already given in the question statement.