based on Professor Plum finding Mr. Body dead at 7 PM in the Dining Room of the Parker Brother Mansion. Mrs. Peacock confesses to Mr. Green that she bopped Mr. Body over the head with a Candlestick during an argument during breakfast that day in a jealous rage over his affair with Miss Scarlet. The temperature in the room is maintained at 20°C by the HVAC system for the mansion. The temperature of Mr. Body is measured to be at 25°C when found and the convective heat transfer coefficient is estimated to be h = 25-W/m2°C. Model Mr. Body as a 30-cm diameter, 1.70-ı %3D long cylinder. Assume the temperature of a healthy person as 37°C. As the average human body is 72 percent water by mass assume the properties of water for this "ball park" analysis. [k = 0.617- W/m-°C, r = 996-kg/m³, c = 4.178-kJ/kg-ºC] The time constant for this Lumped System approach in hours 12.2 cannot be determined 3.19 9.96

based on Professor Plum finding Mr. Body dead at 7 PM in the Dining Room of the Parker Brother Mansion. Mrs. Peacock confesses to Mr. Green that she bopped Mr. Body over the head with a Candlestick during an argument during breakfast that day in a jealous rage over his affair with Miss Scarlet. The temperature in the room is maintained at 20°C by the HVAC system for the mansion. The temperature of Mr. Body is measured to be at 25°C when found and the convective heat transfer coefficient is estimated to be h = 25-W/m2°C. Model Mr. Body as a 30-cm diameter, 1.70-ı %3D long cylinder. Assume the temperature of a healthy person as 37°C. As the average human body is 72 percent water by mass assume the properties of water for this "ball park" analysis. [k = 0.617- W/m-°C, r = 996-kg/m³, c = 4.178-kJ/kg-ºC] The time constant for this Lumped System approach in hours 12.2 cannot be determined 3.19 9.96

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter9: Refrigerant And Oil Chemistry And Management-recovery, Recycling,

Section: Chapter Questions

Problem 17RQ: What is the name of the conference that was held in Canada in 1987 to attempt to solve the problem...

See similar textbooks

Similar questions

On a cold winter day, you turn up the thermostat in your house. Assume that your house is well sealed and that no air enters or leaves the house. When the air temperature in your house rises a short while later, what statement is correct regarding the air pressure? Question 10 options: The air pressure does not change at the higher temperature. The air pressure increases at first but then decreases again as the temperature approaches its higher value. The air pressure is lower at the higher temperature. The air pressure decreases at first but then increases again as the temperature approaches its lower value. The air pressure is higher at the higher temperature.
A metal cylinder is filled with a room temperature perfect gas at 1 atm of pressure; upon pulling on the piston the gas is expanded. The gas of course initially cools, but then warms back to room temperature since it is in a non-insulating metal cylinder.a. What is the net ΔU and why? b. While still pulling on the piston after it warmed to room temperature, I wrap it in insulating glass wool to make the system adiabatic. Then I suddenly stop pulling on it. As no heat can be exchanged with the outside, tell me if the the piston will expand, compress, or stay the same and why?
State the first law of thermodynamics and joules law
Which of the following terms describes the temperature difference in F o that must exist across thesurface area of a structure to drive 1 Btu per hour through 1 square foot of surface.
3. According to Newton's cooling law, the rate of cooling of a hot body is pro- portional to the difference between the temperatures of the hot body and the environment. If the room temperature is 35°C and the temperature of a hot body in the room cools down to 55°C from 105°C Celsius in just 6 minutes, then how many more minutes will it take to cool down to 45°C?
In this discussion, you will briefly explain each of the four gas laws and apply an example as it happens in a refrigeration system. (Boyle’s, Charles’, Dalton’s, and the general law of perfect gases). In your contribution, also address the following: What makes matter change to different states? What type of energy do you think is the most important for the HVAC-R industry?
Which of the two systems performs better.
The temperature before and after the adiabatic process is 200 K and 127°C. The pressure before the process is 500000 N/cm2 and adiabatic index is 2.4, then its pressure after the process is approximately 4000000 N/cm2 Select one: True False
Problem 1. A sample of an ideal gas goes through the process shown in Figure 1. From A to B, the process is adiabatic; from B to C, it is isobaric with 240 kJ of energy entering the system by heat; from C to D, the process is isothermal; and from D to A, it is isobaric with 360 kJ of energy leaving the system by heat. Determine the difference in internal energy Eint B - Eint ‚A P (atm) V (m³) 0.09 0.2 0,4
1. Consider the following schematic of a power plant (operating in what is called a 'Rankine Cycle') Turbine Steam generator Condenser Coling water Economiaer The power plant control room reports that the plant is operating continuously at the following peak load conditions: a. Power to pump = 300KW b. Rate of steam flow = 25 kg/s c. Cooling water temperature at condenser inlet = 13 C d. Cooling water temperature at condenser outlet = 34 C Additionally, the following measurements were made at various points in the piping connecting the power plant components Data Pressure Temp. Quality enthalpy Specific Velocity (kJ/kg) point (kPa) volume (m/s) (m3/kg) (C) (x) 1 6200 2 6100 43 5900 177 ---- 4. 5700 493 ----- 5 5500 482 ----- 6 103 0.94 183 7 96 43 -----
This is thermodynamics 2
Choose correct answer: The temperature before and after the adiabatic process is 200 K and 127°C. The pressure before the process is 500000 N/cm2 and adiabatic index is 2.4, then its pressure after the process is approximately 800000 N/cm2 Select one: True False