A brass tube with an outside diameter of 2.00 in. and a wall thickness of 0.375 in. is connected to a steel tube with an inside diameter of 2.00 in. and a wall thickness of 0.250 in. by using a 0.750-in.-diameter pin as shown in Fig. 4-14a. Determine (a) The shearing stress in the pin when the joint is carrying an axial load of 10 kip. (b) The length of joint required if the pin is replaced by a glued joint and the shearing stress in the glue must be limited to 250 psi.

A brass tube with an outside diameter of 2.00 in. and a wall thickness of 0.375 in. is connected to a steel tube with an inside diameter of 2.00 in. and a wall thickness of 0.250 in. by using a 0.750-in.-diameter pin as shown in Fig. 4-14a. Determine (a) The shearing stress in the pin when the joint is carrying an axial load of 10 kip. (b) The length of joint required if the pin is replaced by a glued joint and the shearing stress in the glue must be limited to 250 psi.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter8: Applications Of Plane Stress (pressure Vessels, Beams, And Combined Loadings)

Section: Chapter Questions

Problem 8.5.11P: The hollow drill pipe for an oil well (sec figure) is 6,2 in. in outer diameter and 0.75 in. in...

See similar textbooks

Similar questions

Compute the tensile stress for the rod shown in Fig. 1 at section A-A, the shearing stress across section B, the compressive stress between the pin and the rod, and the compressive stress between the pin and the yoke. Given n = 1 (3 / 4) in., a = (15 / 32) in., e = (27 / 32) in., b = (15 / 16) in., d = (19 / 32) in., f = 1".
(D) The pin used at B has an ultimate shear strength of 58 ksi. If a factor of safety of 2.5 is required, determine the allowable shear stress in this pin. in ksi (E) The pin used at B is a double shear pin connection. Determine the minimum pin cross-sectional area, and the corresponding minimum pin diameter that can be used at B. (Amin IN in.2 and dpin IN in.) (F) Determine the deformations in rods (1), (2), and (3) when load P equals Pmax from Letter C. ANSWERS in inch (G) Using the results from Letter F, determine the deflections of Joint B and Point D. ANSWERS in inch
Each of the four links in Figure 3 has an 8x36mm uniform rectangular cross section and each of the other four pins has a 16mm diameter. a. Determine the maximum value of the average normal stress in the links connecting points B and D and points C and E. b. Determine the average shearing stress in points B and C.
A 7/8-inch diameter bolt, having a diameter at the root of the threads of 0.731 in., is used to fasten two timbers together. The nut is tightened to cause a tensile stress of 18 ksi in the bolt. Compute the shearing stress in the head of the bolt and in the threads. Also, determine the outside diameter of the washers if their inside diameter is 9/8 in. and the bearing stress is limited to 800 psi. STIL wwwsex Thaan 5/8 in.
A flanged bolt coupling is used to connect a solid shaft 90 mm in diameter to a hollow shaft 100 mm in outsude diameter and 90 mm in inside diameter. If the allowable aring stress in the shafts and the bolts is 60 MPa, how many 10 mm diameter steel bolts must be used on a 200 mm diameter bolt circle so that the coupling will be as strong as the weaker shaft?
3. Determine the maximum average shear stress developed in each -in diameter bolt for the system shown below. 10 kip 5 kip 5 kip
Problem 1: If the parts of the shaft below are a 1" diameter solid steel rod and a 2" OD diameter steel pipe with a 0.25" wall thickness, what is the torsional stress in each section of the shaft? B 6 in. 15 lb 8 in. 15 lb
If the allowable normal stress is 120MPa and the allowable shear stress is 60MPa, what is the B diameter of pin?
A 7/8-in diameter bolt, having a diameter at the root of the threads of 0.731 in., is used to fasten two timbers together. The nut is tightened to cause a tensile stress of 18 ksi in the bolt. Compute the shearing stress (ksi) in the head of the bolt and in the threads. Also, determine the outside diameter of the washers (inches) if their inside diameter is 9/8 in. and the bearing stress is limited to 800 psi. 1/2 in 5/8 in
Torsion. A flanged bolt coupling connects two shafts. The bolt circle diameter is 250 mm in which there are 12 bolts. The allowable shear stress is 55 MPa in the shafts and 23 MPa in the bolts. One shaft is hollow with outside diameter of 100 mm, while the other one is solid of diameter 50 mm. Determine the ratio of the outside and inside diameter of the hollow shaft and the bolt diameter so that both shafts and the flanged bolt coupling are having the same strength in torsion.
6. A PIPE CARRY|NG STE AM AT 3.5 MPa HAS AN OUTSIDE DIAMETER OF 450 mm AND A WALL THICKNESS OF 10 mm. A GASKET IS INSERTED BETWEEN THE FLANGE AT ONE END OF THE PIPE AND A FLAT PLATE USED TO CAP THE END. HOW MANY 40 mm- DIAMETER BOLTS MUST BE USED TO HOLD THE CAP ON IF THE ALLOWABLE STRESS IN THE BOLTS IS 105 MPa, OF WHICH 55 MPa IS THE INITIAL STRESS ? WNHAT CIRCUMFERENTIAL IN THE PIPE ? TO TIGHTEN THE BOLT INITIALLY, AND WHAT WILL STRESS IS DEVELOP WHY IS IT NECE SSARY HAPPEN IF THE STEAM PRESSURE SHOULD CAUSE THE STRESS IN THE BOLTS TO BE TWICE THE VALUE OF THE INITIAL STRESS?
estion 11 62.5 mm Кey 55° The cast iron block with cross-sectional dimensions of 62.5 mm by 62.5 mm consists of two pieces. The pieces are prevented from sliding along the 55° inclined joint by the steel key, which is 62.5 mm long. The working stresses are 275 MPa for cast iron in bearing and 345 MPa for the key in shear. If the block is loaded with P = 256 kN, calculate the required dimension "h" of the key. Write your final answer in 2 decimal places with the unit of mm.