Braids are made by interlacing yarns that move lengthwise and diagonally. Identify other fabrications where yarns also move lengthwise and diagonally. Explain the differences and similarities in serviceability between these fabrics. How can you differentiate among them?

Q: In finding the R2 why do we need to subtract it by 300

A: As per question we have to find radius of curve first that is R1 And when you do the calculation you…

Q: Which of the following can prevent the lateral buckling of steel beams? (There are 3 answers that…

A: Lateral buckling of steel beams- It refers to the twisting and lateral displacement caused by…

Q: Solve the member forces of the following Truss. You must show the manual calculation for U1L1, U2L3,…

A: Data given Find: Member forces

Q: Choose all that apply. The vules of K for effective length of a column when studying its buckling:…

A:

Q: A hollow shaft of external and internal diameters as 100 mm and 40 mm respectively is transmitting…

A: Given a hollow shaft with, External diameter, Dext=100 mm. Internal diameter, Dint=40 mm. Speed, N =…

Q: 3. Three plates are joined with a 12-mm diameter pin as shown below. Determine the maximum load P…

A: Given:- Diameter of pin = 12 mm dia Maximum bearing stress between plate and pin = 650 MPa To…

Q: -1/3 s. It carries a A long, wide channel has a slope of 1:2747 with a Manning's n of 0.015 m…

A: Given data- A long, wide channel- slope S = 1:2747 n=0.015 m-1/3 Discharge q=2.5 m3 s-1 Depth…

Q: Compute the bending stress of the beam shown. Assume that the concrete has cracked and use the…

A: Answer  We know that Bending stress of the beam can be computed using the following equation Bending…

Q: 7. An aluminum rod was pulled in a tensile strength test. The reading is given in the table below.…

A: Following are the given information. Initial length =2.000 in. Final length =2.226 in.

Q: 15 m -15m 50kN -15m- 70KN -15m- E 40KN -15m- 22-5m a.) Determine the forces in the members of the…

A: Since you have asked multiple questions, we will solve the first question for you. If you want any…

Q: Q4. Write a short note on each of the following with respect to the global positioning system (GPS)…

A:

Q: Determine the forces in the members U² U, L L and U L3 of truss shown below: U₂ U₁ U₂ L₂ U₂ th₂. L5…

A:

Q: Compute the elevations of BM2? STATION BM 1 TP 1 TP 2 TP 3 TP 4 BM 2 BS 2.71 3.62 3.51 3.17 1.47 HI…

A: Given,

Q: A 7350 m long, 1050 mm concrete pipeline connects an upstream reservoir (water surface elevation…

A: Following are the given information. Pipeline length =7350 m Pipeline diameter =1050 mm=1.05 m…

Q: Question 1 A composite beam cross section is made up of two rectangular strips. Each of (100x50) mm…

A:

Q: A tank with an initial concentration of 500 mg/L receives a 10 L/min inflow containing 5 mg/L and a…

A: Given,  Cin = 5 mg/L Qin = 10 L/min Min = 100 mg/min Qe = 10 L/min

Q: What is the overthrow required for a train of wheel base 1.5m to move on a 5 degree curve? 0.89 mm O…

A: Given -  Wheel base = 1.5 m Degree curve = 5  To find -  What is the overthrow?

Q: Design a wide-flange (W) column 20 ft. on length to support an axial load of 410 Kips in the…

A: Given data: Length of column, L=20 ft Axial load on column=410 kips Column is fixed at base and top…

Q: .40. A solution is known to contain 50 g/m³ of CH3(CH₂),COOH and 42 g/m³ of NH3-N. Determine the…

A:

Q: A 100mm diameter 2014-T6 aluminum axle is subjected to the loads shown. Use Castigliano's method to…

A: Data given 2014-T6 Aluminum axle , E = 73.1 GPa D  = 100 mm = 0.1 m Find :  vertical displacement…

Q: 10 m Draw contour lines for 50 m ,49 m, 48m, 47m, 46m, and 45 m for the following grade The box…

A: The data is provided in the above question. We have to find out the followings Approximate contour…

Q: A 25 ft long soldier beam is used as a key component of an earth retention system at an excavation…

A:

Q: CONSTRUCTION LABOR GIVEN: A bedroom & bathroom with floor area of 45sq.m., productivity of 1…

A:

Q: The work done by a 1 kN of water jet moving with a velocity of 60 m/sec when it impinges on a series…

A: Given data- velocity V=60 m/s,Force F=1 kN,velocity of vanes=9 m/s,To Find-The work done by the jet.

Q: Use principles of superposition to solve all reactions.

A: Given:- EI=40×106 kip-in2 To find:- Reactions Shear force and moment diagrams Concept:- The…

Q: In class, we used superposition principles to solve reactions for a propped cantilever beam. Take a…

A: Given: Required: Reactions, shear force diagram and bending moment diagram

Q: For this problem, can you explain why they are are R^2-1/4piR^2*L for the volume part of the…

A: Fv= pgV  p = Density of the fluid  g = acceleration due to gravity  V = Volume above the curved…

Q: Compute for the ultimate moment capacity of an am simply supported steel beam with the properties…

A: Answer  (a) Unbraced length Lb =3 m, Cb =1 Lp = 1.76ryEFy Lp = 1.76*21.51200000250 Lp = 1070.77 mm…

Q: Determine the design capacity of the given tension member. Assume that the Slenderness requirement…

A:

Q: An urban freeway is to be designed using the following information. AADT = 52,500 veh/day K…

A: Given:- AADT = 52,500 veh/day K = 0.12 D = 0.65 Trucks = 8% of peak hour volume PHF = 0.94

Q: Water is pumped 14.5 km from a reservoir at elevation 30 m to another reservoir at elevation 70 m.…

A:

Q: a building project. There are three pits from which these materials can be obtained. The composition…

A:

Q: Four activities to be undertaken in series for the completion of a project are as following:…

A: The data is provided as above. Optimistic time, pessimistic time, and most likely time of activities…

Q: 5.10 Draw the shear and bending-moment diagrams for the beam and loading shown, and determine the…

A:

Q: A vertical gate 1.60m wide and 2.00m high has water on one side and is inclined 45o with the…

A:

Q: 2. Determine the reaction of the beam supports and draw the shear and moment for the beam shown 18…

A:

Q: What is the overthrow required for a train of wheel base 1.5m to move on a 5 degree curve? 0.89 mm O…

A: Given -  Wheel base = 1.5 m Degree curve = 5

Q: AT beam having a span of 6m has a web thickness of 300mm and an effective depth of 600mm. The beams…

A:

Q: Consider the following data from a test on Pelton wheel? Head at the base of the nozzle = 32 m…

A: Given data- Discharge of the nozzle Q=0.18 m3/s, Head at the base H=32 m, Area of jet a=7500 mm2,…

Q: A swimming pool, 15m long x 10m wide x 3m deep at one end and 1.50m on the other end,  is filled…

A: To determine: The time required to drain the full contents of the pool.   The Given Data: The…

Q: (2) #3 at 8"0.c. 4#9 14" 21" fé= 5000 psi NWC Grade 60 steel & Mn = ? Tied Bars.

A: As per Bartleby's guidelines we are supposed to answer only first question. Kindly repost other…

Q: Use Castigliano's method to determine the vertical displacement of point B of the reinforcement…

A:

Q: (a) Use the Force Method to solve the reactions and find the forces in each member of the truss…

A:

Q: A steel wire of length 2.0 m is subjected to tension and produced an elongation of 3 mm. What should…

A: Given:- Length of steel wire = 2 m Elongation in the wire = 3 mm Original diameter of wire = 1.5 m E…

Q: EX/ Find h to cause Zero normal stress at Point (b) at base of dam. Find a B=1m 3m Assume Xw = 10…

A: Given data: Unit weight of concrete, γconc=24 kNm3 Unit weight of water, γwater=10 kNm3

Q: free-body diagram of the joint on either of the cut is known, we can apply the equations of…

A:

Q: A secondary road in a developing country, 30 km long is to be improved by surface treating the…

A: Given length of road = 30 km cost of improvement = $150,000/- per km Total cost of improvement for…

Q: (3) #4 at 8" O.C. 4#8 12" 13" 6" 15" fó= 3000 psi NWC Grade 60 steel & M₁ = ? Tied Bars

A: According to the guidelines, it is requested to post the second question separately. As=4(0.79)=3.6…

Q: The process of submitting a proposal (tender) to manage a construction project   a. Negotiation b.…

A:

Q: In the fig. Given, 1. Write the shear and moment equations between change of load points. 2. Without…

A: Given: Required: Shear and moment equations Shear and moment diagram , when an additional 5 KN…

Reactions with Materials

Limestone