Calculate the coefficient of permeability in mm/s of a soil sample, 6 cm in height and 50 cm2 in cross sectional area, if a quantity of water equal to 430 ml passed down in 10 minutes, under an effective constant head of 40 cm. a.625 X 10^-2 b.5.9 x 10^-2 c.1.6 X 10^-5 d.2.15 x 10^-2

Calculate the coefficient of permeability in mm/s of a soil sample, 6 cm in height and 50 cm2 in cross sectional area, if a quantity of water equal to 430 ml passed down in 10 minutes, under an effective constant head of 40 cm. a.625 X 10^-2 b.5.9 x 10^-2 c.1.6 X 10^-5 d.2.15 x 10^-2

Principles of Geotechnical Engineering (MindTap Course List)

9th Edition

ISBN:9781305970939

Author:Braja M. Das, Khaled Sobhan

Publisher:Braja M. Das, Khaled Sobhan

Chapter11: Compressibility Of Soil

Section: Chapter Questions

Problem 11.15P

See similar textbooks

Related questions

Q: Determine average shear stress for rectangular cross section if maximum shear stress value is 22 MPa

A: Introduction : The given question is related with solid mechanics . In this question we are provided…

Q: Is truss stable or not

A: Given data : The number of member in truss structure m=21 The number of joint in truss structure…

Q: Calculate the chainage of the tangent points of the compound curve from the following: Stat.…

Q: Determine the allowable load on a 3 m long layered built-up column made up of 6 nominal 2”x 6”…

A: Solution-The given values are as follows,The length (L) =3m=300mm6 nominal 2”x 6” piecesThe actual…

Q: Determine velocity KE-2300 J m-23 kg

Q: Problem 2 6200 lb Determine the magnitude and direction of the resultant of the three forces acting…

A: Open the force compoment along the x direction and y direction.

Q: A 6 m long cantilever concrete beam is supporting a uniformly distributed load of w = 2 kN/m and a 3…

A: To find slope and deflection at C

Q: Determine the force in member CD of the truss. State if the member is in tension or compression.…

A: ASKED: To determine the force in member CD of the given truss. Let us apply the method of section…

Q: Problem 1 Determine the magnitude of the moment about point A and its direction at the plane having…

Q: 3- The time for 65% consolidation of a 1.12-inch clay specimen (drained at top and bottom) in the…

Q: E P Cable 4 m D В C A -2 m -2 m- 3 m

Q: A plate with width of 400mm and thickness of 12mm is to be connected as shown in the figure. The…

A: “Since you have posted a question with multiple sub-parts, we will solve first three subparts for…

Q: The depth of water in a 3-m wide, rectangular, finished concrete channel is 2-m. If the slope is…

Q: The major and minor principal stresses at a point are 3Mpa and -3MP respectively. The maximum shear…

Q: A pipe network is show in figure below; find the distribution of discharges in all pipes and…

Q: A cylinder has settled in equilibrium. It is immersed in 2 liquid layers, water and a non- polar…

Q: For a cantilever beam shown below B Use the method of moment-area to calculate the vertical…

Q: Determine the x- and y-coordinates of the centroid of the shaded ar ! 3", 3" 4" 1.25" 10" 1.25" 3" B…

Q: Determine the value of force applied if work done is 202 J and value of displacement is 2.5 m

A: Introduction : The given question is related with mechanics . In this question we are provided with…

Q: Given a chance to talk to riverside or seaside residents who (1) have no background on engineering…

A: Hydrographic surveying is a branch of surveying any water body of water such as a lake, harbour,…

Q: Please make your own question about traverse survey and solve it on your own. Make it original. Do…

Q: Will rate immediately. Need ASAP a. which of the ff gives the maximum shear in the beam? b. which of…

Q: What diameter of pipe is required to carry 10 gpm of gasoline at a velocity of 7 ft per sec?

Q: he depth of 0.6 m. A hump of height 10 cm is placed in the bottom of the channel. Flow rate of the…

A: Width of Beam = B = 1.2 m Depth at upstream level = Y1 = 0.6m Height of Hydraulic jump = ΔZ = 0.1m…

Q: Draw the the 3 principal views and auxiliary view (like in the second photo)

A: Auxillary view: The orthographic view drawn taken according to the line of sight which is not…

Q: Analyze the truss given below using the method of joints. 2) PI is equal to the first two digits of…

A: Note: Hi! Thank you for the question As per the honour code, We’ll answer the first question…

Q: A rectangular beam has b=250mm, d=330mm, fy=414,fc'=20.7MPa. Determine the the maximum design moment…

Q: Please make your own question about horizontal and vertical angles (surverying) and solve it on your…

Q: ot boon sT Consider an inner beam-column joint in the ground floor roof of a eight storey building…

Q: What is the appropriate radius of the central curve if an 80-m spiral easement curve has a distance…

A: Given data, Spiral curve length = 80 m Distance along tangent at its third quarter point (Xs) =…

Q: ulate the chainage of the tangen wing: P.I=28+50 500m. Ø1 = 38° 20' 750m. Ø2 = 41° 30'

Q: The velocity profile for laminar flow of water between two parallel plates as shown in figure is…

Q: What is the purpose of having an aeration tank water waste water treatment plants? Describe what…

A: Que:- What is the purpose of having an aeration tank water wastewater treatment plants? Describe…

Q: A rectangular scow 7 ft by 18 ft by 32 ft long loaded with garbage has a draft of 5 feet in water.…

A: Given: Rectangular scow = 7 ft * 18ft * 32ft Depth of scow in water = 5ft, Height of center of…

Q: termine the

Q: Find the coordinates of points A, B, C, D and E by adjusting this traverse. Complete all cells in…

A: Given data sheets are not sufficient to solve the problem

Q: Question 11 of 14 View Policies Current Attempt in Progress Calculate the y-coordinate of the…

Q: Block ABCD accepts two centralized loads such as depicted. It is known that the cross-section of the…

A: First draw the shear force and bending moment diagram. Then assess the value of maximum BM and SF…

Q: determine the maximum flexural stress and maximum shear stress of the beam

Q: A simply supported beam with proportional loading (P = 4.1 kN) has span length L = 5 m. Load P is…

A: First calculate the reaction at B. Then using the relevant FBD the value of bending moment can be…

Q: In the figure shown, sub-critical uniform flow occurs in a 1.2 m width rectangular channel at the…

Q: Problem 3 - 113 A rectangular scow 7 ft by 18 ft by 32 ft long loaded with garbage has a draft of 5…

Q: Moment Area Method 1. Determine the slope at points B and C of the beam given. IfE = 200 GPa and I =…

Q: Problem 3 - 111 A block weighing 125 pcf is 1 ft square and 9 inches deep floats on a stratified…

Q: The 5-story building design project will have its beams and slab poured monolithically and formed a…

A: Solution: Given: Area of steel at tension 9-36 mm Ast = 1006 mm2 Total Ast = 9x1006=9081 mm2 Area…

Q: Determine the distance y to the centroid of the beam's cross-sectional area. Set a = 70 mm , b = 240…

Q: For the 2-D linear triangular plane stress element below (figure 3), the nodes' displacements have…

Q: A submerged clay layer has a thickness of 8m. the water content of the soil particles is 50%. The…

Q: .2. Н20 y1 20 сm Hg

Q: A foundation is proposed, which wil be placed on to a 4 m thick stratum of homogeneous saturated…

Concept explainers

Field applications of hydraulic conductivity

Hydraulic conductivity is one of the hydraulic properties of soil defined as a measurement of the ability of a porous medium to permit water movement or fluid flow through it. It is denoted by the letter K. It is influenced by the density and viscosity of the fluid. It is also called permeability. Hydraulic conductivity is defined as the ratio of velocity to the hydraulic gradient. The different methods used to determine the hydraulic conductivity are laboratory methods (constant head permeability tests and falling head tests), in-situ field methods (pumping in and pumping out tests), small scale field tests (infiltration tests and slug tests), and indirect methods such as estimation from grain size, consolidation test data, and horizontal capillary test. The pedotransfer function (PTF) method is a specific empirical estimating approach employed in the soil sciences is also used to determine the hydraulic conductivity of the soil.

Question

a.625 X 10^-2

b.5.9 x 10^-2

c.1.6 X 10^-5

d.2.15 x 10^-2

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Field Applications of Hydraulic Conductivity

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Hydrometer and sieve analysis were conducted on a soil sample. Find D10 Deo uniformity coefficient (Cu), coefficient of curvature (CC) considering the chart given below. Hint: Cu=Deo/D10 and CC=(D3)2 / (D1oxD6o) 100 90 80 70 60 50 40 30 20 10 0,001 CLAY 0,01 SILT 0,1 SAND GRAVEL 10 100 DANE ÇAPI/ PARTICLE SIZE (mm) Dec: (in mm) seç. CC Seç. Cu Seç. D10: (in mm) Seç. GEÇEN DANE YÜZDESİ / PERCENT FINER THAN D
Soil Mechanic A fully saturated soil sample has a volume of 28 cc. The sample was dried in oven and the weight of the dry soil pat was found to be 48.76 g. Given G= 2.68. Determine volume of water in cm3. a. 53.6 b. 18.23 c. 9.77 d. 20.0
2. The sieve analysis data for a granular soil are given below. NICS LECTUREY % passing 19 mm sieve =100 % passing 4.75 mm (4 sieve) = 61 % passing 2 mm = 45 % passing 0.075 mm (200 sieve) = 16 %3D % passing 0.06 mm (4 sieve) = 13 % passing 0.05 mm ( sieve) = 8 % passing 0.002 mm (4 sieve) = 5 What are the percentages of gravels, sands and fines within this soil, based on the Unified Soil Classification System (USCS), AASHTO, USDA and MIT Standards? Mass Opening (mm) Sieve No. Retained (g) 4.75 4
76 .ll Q3.png The data from standard and modified proctor test on a soil sample (density of solids: 2680 kg/m3 ) are provided below: Standard proctor test Modified proctor test Dry density (kg/m) 1691 Dry density (kg/m') 1873 Water content (%) Water content (%) 9.3 9.3 1715 11,8 1910 12.8 1755 14.3 1803 15.5 1747 17.6 1699 18.7 1685 20.8 1641 21.1 1619 23 a) Plot the compaction curves (both standard and modified in one graph). b) Establish the maximum dry density and optimum water content for each test.
Constant head test was conducted to determine the permeability constant of a certain soil sample. The table below shows the data gathered: Constant Head (cm) 29.14 Elapsed Time (s) Add your answer 141 Outflow Volume (cm³) 939 KT (cm/sec) The inner dimensions of the ring are: d = 6.2cm and h = 1.92cm where d is the diameter of the ring and h is the height of the ring. Determine the coefficient of permeability (cm/sec) of the soil sample. Round your answer to 4 decimal places.
A permeameter tube (square cross-section) is filled with layers of soil of different permeability as shown below. Find the equivalent permeability for the assembly of soils Find the Total head, elevation head and pore water pressure at points (A, B, and C) with respect to the given datum. Given: k1=2k2=3k3=k4= 2x10³ cm/sec All units are in cm 55.0 F12.512.5 k ki 15.0HA k1 100 30.0 20.0 40.0- k2 Datum 5.0
Question 3 4 pts Assuming the groundwater table is at ground surface and the soil bulk unit weight is 20KN/m3. At 2m depth below ground level. The pore water pressure is approximately: 200 kPa O 9.8 kPa O 98 kPa O 19.6 kPa Question 4 4 pts A soil sample is placed in a 1m long and 10cm diameter tube. A constant supply of water is allowed to flow from inlet to outlet. The total water head at the inlet is 2m and the total water head at the outlet is 1m. The hydraulic conductivity is 0.001 cm/s. Which of the following answer is correct? O The flow velocity is 25 cm/s O The hydraulic gradient in the tube is 2 O The flow velocity is 0.001 cm/s O The hydraulic gradient in the tube is 0.001
Calculate the CEC (m.e./100g soil) using the following given miliequivalent weights obtained from a 25g soil sample (a. Ca++= 2.23 m.e; b. Mg++=1.32 m.e.; c. Na+= 1.98 m.e.; d. K+= 1.87 m.e.; e. H+= 1.27 m.e.; f. Al+++= 0.11 m.e.; g. NH4+= 2.3 m.e.; h. NO3-= 1.5 m.e.
4. For the soil specimen shown in figure, calculate the soil permeability if rate of flow is 2 cc/min. Take area of cross-section of soil specimen as 8 cm2. 15 cm 5 cm 12 cm a. 4x10°cm/sec b. 5x103cm/sec c. 6×10°cm/sec d. 7x103cm/sec
Q1/ specimen of the fine-grained soil, 75 mm in diameter and 20 mm thick was tested in an oedometer in a laboratory. At applying pressure (240 kN/m²), the time with dial gauge readings are: Time (min) 0 Settlement (mm) 0 0.25 1 0.22 0.42 4 9 0.6 0.71 16 0.79 36 64 100 0.86 0.91 1.04 d 1- Find Coefficient of consolidation in cm²/s using root time and TV90% = 0.848. Scanned by TapScanner
Find the value of Cc of the following soil data sample Weight Percentage Cumulative Percentage Sieve Weight retained (gm) percentage retained (C) retained finer S.NO Select one: O a. 10.85 size (gm) N = (100 - C) {W,/ W,} x 100 1 75mm 100 O b. 7.36 63mm 100 O c. 18.34 50mm 100 O d. 2,96 4 37.5mm 454 22.7 22.7 77.30 5 28mm 285 14.25 36.95 63.05 6 20mm 207 10.35 47.30 52.70 7 14mm 318 15.90 63.20 36.80 8 10mm 206 10.30 73.50 26.50 6.3mm 118 5.90 79.40 20.60 10 5.0mm 102 5.10 84.50 15.50 11 3.35mm 64 3.20 87.70 12.30 12 2.0mm 88 4.40 92.10 7.90 13 1.18mm 35 1.75 93.85 6.15 14 600µ 42 2.10 95.15 4.85 15 300µ 33 1.65 97.60 2.40 16 150µ 18 0.90 98.50 1.50 17 75µ 22 1.10 99.6 0.40 18 Pan 8 0.40 100 In the pan we have = 100 W,= 2000 2 -99.6 = 0.4 % of material 2. 3.
For a soil, given: D10 = 0.08 mm D30 = 0.22 mm D60 = 0.41 mm Calculate the uniformity coefficient and the coefficient of gradation of the soil. 2.4 Repeat Problem 2.3 for the following: D10 = 0.24 mm D30 = 0.82 mm D60 = 1.81 mm