6.7.Calculate the induced vertical stress at point A at a depth of 5 feet. Thesurface stress in the shaded areas is 3000 lb/ft2. Hint: The contributions ofthe shaded areas must be calculated separately and then added together.The contribution from the lower area will require the use of imaginaryrectangles. (Answer: 1892 lb/ft2, yours may differ slightly)Four 40' diameter fuel tanks are constructed in a square pattern. The tanks apply amaximum surface pressure of 5000 lb/ft2. The spacing of the tanks is 50 feet center-center. What is the induced vertical stress beneath the center of the area at depths of 20feet and 50 feet? (1400 and 1700 lb/ft2, some variation expected from chart reading)

Using stress influence chart for stresses under corner of a rectangular footing with uniform loading…

Calculate the induced vertical stress at point A at a depth of 5 feet. The surface stress in the shaded areas is 3000 lb/ft2. Hint: The contributions of the shaded areas must be calculated separately and then added together. The contribution from the lower area will require the use of imaginary rectangles. (Answer: 1892 lb/ft², yours may differ slightly) A 3

Calculate the induced vertical stress at point A at a depth of 5 feet. The surface stress in the shaded areas is 3000 lb/ft2. Hint: The contributions of the shaded areas must be calculated separately and then added together. The contribution from the lower area will require the use of imaginary rectangles. (Answer: 1892 lb/ft², yours may differ slightly) A 3

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

T2 Problems for Practice Situation 4 A point load P = 5 kN at the origin (0, 0, 0) of a ground surface which is at plane z = 0. P 1. Calculate the stress increase at (3, 4, 0) (0 kPa) 2. Calculate the stress increase at (3, 4, 6) (0.018 kPa)
A typical stainless steel cylindrical vessel is shown. The inside diameter of the tank is 48.0 in. and the wall thickness is 0.75 in. The tank is pressurized to 1.01 ksi. Determine the hoop stress in the wall of the tank. 34.5 ksi 40.9 ksi 44.1 ksi 38.5 ksi 32.3 ksi
A thin cylinder have inner radius 235 mm and thickness 6 mm subjected to an internal pressure of 5 MPa. Determine average circumferential stress?
4) The utility has decided to build a transformer pad at the same site as the previous question. The pad is to be 3 m wide by 5 m long, bearing directly at the ground surface with a uniform pressure of 250 kPa. a) Calculate the vertical stress increase at points A (center), B (corner), and C (edge) as shown below (hint: use superposition) to a depth of 15 m. B В - 3 m L- 5m b) Calculate the vertical stress increase at point A using the 2:1 approximation given below. Compare the results to those obtained using the more rigorous method. c) Assume the pad to be a strip footing with the same width, and calculate the vertical stress increase at point A. d) From the calculated stress distributions above for both the rectangular and strip footing assumption, at what depth is the distributed stress equal to 10% of the surface pressure?
Problem # 4: The tank shown is fabricated from steel plate. Determine the minimum thickness of plate which may be used if the stress is limited to 42 MPa and the internal pressure is 1.5 MPa. USING BOTH TANGENTIAL AND LONGITUDINAL STRESS FORMULA.
A hollow circular tube is subjected to a tension force of 30 KN, a tensile stress of 20 MPa was recorded.lf the outer diameter of the tube is 100 mm, the inner diameter will be eqaual to. a. 93.95 mm O b. 89.95 mm C. 85.95 mm o d. 91.95 mm
Q6. Hoop stress (0₁) in a thin-walled pressure vessel is 40 MPa. What is the maximum 'in-plane' shear stress? A. 40 MPa B. 15 MPa C. 10 MPa D. 8 MPa E. 40√2 MPa ofi $₁
A hoop shrunk onto a hallow tube exert a contact pressure of 3 ksi on the tube. An internal pressure of 10 ksi is then applied to the tube. The inner and outer radii of the tube are 1.5 in and 2.5 in, and 2.5 in and 4 in for the hoop. What is the maximum tangential strss in the tube after application of internal pressure? Also plot tangential stress variation diagram across the section.
QUESTION 6 A 12 inch Schedule 80 natural gas pipe running along the sea-bed at a depth of 7522 ft has an internal pressure of 728 psi. What is the tangential stress in the pipe at the inside surface? Answer in ksi, and pay attention to the sign. Note that seawater has a weight density of 0.037 Ibpin.
What would be the change ineffective stress at point A if the water table rises to 2m above ground level? see figure below a. lower b. higher c. no change in effective stress?
1. Fill in the blanks; (a) Theoretically, the vertical stress at surface under a point load is (b) The curve connecting all the points below the ground surface of equal vertical stress is called The distribution of vertical stress under uniformly loaded area of any (c) shape can be calculated with the help of ............
A soil profile consists of a clay layer underlain by a sand layers as shown. A tube is inserted into the bottom sand layer and the water level rises to 1.2m above the ground surface. Determine the effective stress at pt. A Determine the effective stress at pt. B. Determine the effective stress at pt. C Please answer this asap. For upvote. Thank you very much