Describe what happens to the "power" in this RLC series circuit as the capacitance decreases. Circuit DiagramC110uFComputed ValuesCompute the expected power factor of the circuit given the different capacitance.Live (RMS)Capacitance (UF) Real Power (Watts) Reactive Power (Vars) Power Factormag (A)800.8364.650.914100765.58393.00.893.9190717.07422.560.863.7980662.84450.150.833.6370595.45480.110.783.4760488.91483.330.713.1350375.10472.560.622.7540251.33424.300.512.2430125.93326.100.361.592035.11181.510.190.8410000ol0R1L150Q 10mHV1220 Vrms60 Hz0°LI

Capacitive reactance is inversely proportional to capacitance and frequency Inductive reactance is…

Circuit Diagram C1 10uF ~ 60 Hz 0° Computed Values Compute the expected power factor of the circuit given the different capacitance. (RMS) Capacitance (UE) Real Power (Watts) Reactive Power (Vars) Power Factor 800.8 364.65 0.91 100 765.58 393.0 0.89 90 717.07 422.56 0.86 80 662.84 450.15 0.83 70 595.45 480.11 0.78 60 488.91 483.33 0.71 50 375.10 472.56 0.62 40 251.33 424.30 0.51 30 125.93 326.10 0.36 20 35.11 181.51 0.19 10 0 0 0 0 R1 L1 50Q 10mH V1 220 Vrms mag (A) 4 3.91 3.79 3.63 3.47 3.13 2.75 2.24 1.59 0.84 ol

Circuit Diagram C1 10uF ~ 60 Hz 0° Computed Values Compute the expected power factor of the circuit given the different capacitance. (RMS) Capacitance (UE) Real Power (Watts) Reactive Power (Vars) Power Factor 800.8 364.65 0.91 100 765.58 393.0 0.89 90 717.07 422.56 0.86 80 662.84 450.15 0.83 70 595.45 480.11 0.78 60 488.91 483.33 0.71 50 375.10 472.56 0.62 40 251.33 424.30 0.51 30 125.93 326.10 0.36 20 35.11 181.51 0.19 10 0 0 0 0 R1 L1 50Q 10mH V1 220 Vrms mag (A) 4 3.91 3.79 3.63 3.47 3.13 2.75 2.24 1.59 0.84 ol

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.1MCQ: The rms value of v(t)=Vmaxcos(t+) is given by a. Vmax b. Vmax/2 c. 2Vmax d. 2Vmax

See similar textbooks

Similar questions

Find the DC value and RMS value from this image in below. , I want the solution in a detailed picture with a white paper and a clear font. Thank you.
The maximum transferred average power to a load without restrictions calculated in terms of the RMS (effective) value of Vth is: Select one: O a. IVthl/Rth O b. Vthl2/4.Rth OC. IVl²/8.Rth O d. IVl²/2.Rh
Another name for the RMS value of current or voltage is ... O the effective value O the exact value O the true value O the reactance value
Find thr RMS value..
2. For a sinusoidal voltage trace displayed by the CRO, the time/cm switch is on at 500µs/cm and volt/cm switch is on 5V/cm. The width of one complete cycle is 4cm and peak to peak height is 5cm. Find (a) the frequency, (b) peak to peak voltage, (c)the amplitude and (d) the rms value
The single phase AC sinusoidal voltage then the rms value of the voltage v is .........
A complex voltage waveform which has an rms value of 240V contains 30% third harmonic and 10% fifth harmonic, both of the harmonics being initially in phase with each other. (a) Determine the rms value of the fundamental and each harmonic. (b)Write down an expression to represent the complex voltage waveform if the frequency of the fundamental is 31.83 Hz.
A chopper circuit has an inductive load of 2ohm resistance and 10mH inductance. If the source voltage is 20 V and the frequency of the chopper is set to 100Hz and the on-time to 5 ms. Determine the average voltage and current, maximum and minimum load currents.
Q.1) A single phase load consisting of 5 2 in series with an inductance of 0.02297 H is operated in a phase control mode with a of 90°. The source is 240 V RMS, 60HZ. Find: a) Draw the waveform of VTI and VR. b) Find the conduction angle (6). c) Calculate the RMS value of load current. d) Find the power factor e) What is the minimum value of a for which phase control is in effet. f) Find the size of the first three terms in the Fourier series for the current. T Zoom
Find the RMS value..
For the waveform shown, determine: (a) Peak to Peak value (b) Peak value () RMS value (d) Frequency. If volts/div is 3V/div and Time/div is 25ms/div (No need to show the calculations)
The output voltage waveform of a four quadrant chopper is shown in figure. In the waveform, Vdc is input voltage, D is duty cycle ratio and T is cycle time. DT T. The RMS value of ripple component in output voltage is (A) Vác 2V VD-D (В) V(2D-1) (C) de de (D) V de VD- D? yd