Circuit outputs F(A,B.C) = E(2,4,6) designed with 8 - Decoder 3 - to the number of state 2 in 00000100 00100000 01000000 00100100
Q: Binary to Octal Decoder using 7-Segment Display
A: To design Binary to Octal Decoder using 7-Segment Display
Q: realize the function ? = ∏?(0,1,5,7) using a decoder with inverted outputs
A:
Q: Consider the input samples x(n)= (0, 0.4, 1.6,0.8,1, 2.3,2.7), Explain how encoding and decoding is…
A:
Q: Implement a 4 to 2-line priority encoder. Where the highest priority in input I, and the lowest in…
A:
Q: find 1- Number of bits to design the counter 2- The digital conversion (Binary form) of analog input…
A: It is being given that : Clock generator frequency FC=32 Hz. Slope of voltage to time converter…
Q: 2- Given a BCD decade counter, show the decoding logic required to decode each of the following…
A: (a) For getting HIGH output when the counter counts 0110, the decoding logic needed for decoding the…
Q: Suppose a circuit is required to recognize the 4-bit pattern (1100), and the output (z=1) whenever…
A:
Q: .F(A, B, C, D) = Em(0,4,7,9,10,11,14,19,25,27,28,31), implement this n-variable function using a…
A:
Q: 4.8 For the 4-bit weighted-resistor DAC shown in Figure 4.5, determine the output from the resistors…
A:
Q: The subject is Digital System Please send the answer by typing ONLY. I don't want any handwritten.…
A: In this question we will write applications of encoder and decoder circuits...
Q: In a multiplexer with n input bits, how many output bits are there? O a. None O b. n О с. 1 O d. log…
A:
Q: 2. Write a Verilog or VHDL module (with correct syntax) called Decoder_2to4 to generate a 2 to 4…
A:
Q: (a) two NAND gates (b) two AND gates
A:
Q: analogReadResolution() instruction accept bit resolution up to 16 12 32
A: analogReadResolution() instruction accept bit resolution up to 12bit.
Q: esign a 4-bit combinational circuit that counts DOWN and UP. Counts 1 - 7 only. The first and the…
A: A truth table is a tabular representation of the digits with 0 and 1, which shows the working of the…
Q: A 0.7-V input would be considered a ------------- (forbidden, HIGH, LOW) input to a TTL device.
A:
Q: Decoder circuit as shown in the following Figure. if A is LSB and C is MSB, the output expression F=…
A: The given circuit is 3:8 decoder. Inputs= A,B,C Outputs= Y0, Y1,.........Y7
Q: نقطتان )2) Q7/ The minimum decoders using to design 6- to-64 decoder are
A:
Q: In 8255 to 8086 interface system, chip select signal is derived on the basis of A7-A4-1001 and…
A:
Q: Design a 6-3-1-1 to BCD code converter by using decoder
A: Let the input to the Decoder is 6-3-1-1 which is A,B,C,D and the output of the decoder is BCD which…
Q: Q4/The minimum decoders using to design 6- to-64 decoder are
A: The explanation is as follows.
Q: A) What are the addressing mode and physical address for each instruction if you know…
A: Given Register address of a 8086 microprocessor.we need to determine the physical address of the…
Q: 24/ Decoder is a digital circuit which comprises both logic gates and memory elements. Select…
A: A decoder is a combinational circuit that help the particular code to activates the particular…
Q: What hex address will be decoded by the instruction OUT 6D, AL?
A: AL is the lower 8 bits OUT : Which output data from accumulator with 8 bit addresses Here the…
Q: Design two of the following functions with (a) a multiplexer and (b) a decoder. F(W,X,Y,Z) =…
A: Multiplexer: A multiplexer has 2n inputs and "n" selection lines, At any given time only one of the…
Q: 1 Design a synchronous counter by taking account the foolowing counting order;…
A: “Since you have asked multiple questions, we will solve the first question for you. If you want any…
Q: ir I need the solution step by step and clear line please Example Assuming that a 3-bit ADC channel…
A: To calculate all
Q: mplement a 8:1 Multiplexer using 2:1 Multiplexers. NOTE: Please explain clearly, make a truth table,…
A: Given: Implement 8:1 Multiplexer using 2:1 Multiplexers. According to question: For Designing: Here…
Q: How many decoders 3:8 Decoders and 2 inp-And gates needed to construct 4:16 decoder?
A: Encoders and decoders are a part of combinational logic circuits. A decoder has n inputs and 2^n…
Q: F(A,B,C)=∑(0,1,3,4,5) ,Perform with a data selector by making the accuracy table of the function.
A:
Q: Show (give an example other than the one in Figure 6.5 ) that two-dimensional parity checks can…
A: Let us take an example as below with no-errors.
Q: Q4/The minimum decoders using to design 6- to-64 decoder are * A 20( 2- to- 4 decoder) without…
A: A decoder is a combinational circuit with a maximum of 2noutput lines and n input lines. A circuit…
Q: Diagram of Circuit: Even Parity generator Parity(P) Original Data D- D- Transmitted data with parity…
A:
Q: An analog signal in the range 5V to 10V is to be converted to a digital signal with a quantization…
A: In the first question we know that quantization error is half of the step size. With the help of…
Q: Q3:(a)Draw the seven-segm ent di splay and write the BCD-to--seven segment decoder truth table
A:
Q: 7. Design 4 to 1 mutiplexer using the design procedure
A: as per our guidelines we are supposed to answer?️ only one question. Kindly repost other questions…
Q: A reset input is used in IC 7493, why? a. For reset the counter b. For setting the counter…
A: In IC 7493, the reset inputs are used to reset the counter to 0000.
Q: Consider the input samples x(n)= (0, 0.4, 1.6,0.8,1, 2.3,2.7), Explain how encoding and decoding is…
A:
Q: 2. Take a 10-bit binary fraction and apply subtraction using an 8-bit fraction from it. (Decimal…
A:
Q: 6-Which of the following 8051 registers is a 16-bit register? 1-PSW 2-R0 3-A 4-DPTR
A: Register are used in CPU to store the information on temporary basis.The most widely used registers…
Q: How many 1*2 Decoders are required to design 4*16 Decoder? *
A: Decoder: It is a combinational circuit with n input lines and 2n output lines. Out of these output…
Q: Q3:- Design of Binary 0,1, 2,3 to SEVEN SEGMENT Decoder
A: The most important component of the circuit is the decoder. A decoder is a simple circuit that is…
Q: Design 2-bit synchronous counter that counts 0, 1, 2, 3 in succession.
A: Synchronous counter are sometime called parallel counter as clock is feds in a parallel to all the…
Q: (15) 10 (4)10 (3) 10 4 4 0 1 2 S₁=1 3-to-1 Multiplexer 4 (?) 10 So=0
A:
Q: Design 2-bit synchronous counter that counts 0, 1, 2, 3 in succession
A:
Q: For each of the following 12-bit PCM, determine the 8-bit compressed code, decoded 12-bit and the…
A: 1. 100001000000 So, 8-bit compressed code can be written as: So, for given 12-bit code, the…
Q: How to represent a priority encoder by using truth table and draw a diagram
A: The binary encoder is used to compress a large number of the inputs to a smaller output. For…
Q: Explain the concept of channel coding; what is its function on the overall digital communication…
A: Communication System- Communication System is refer to the system which transfer an information from…
KVL and KCL
KVL stands for Kirchhoff voltage law. KVL states that the total voltage drops around the loop in any closed electric circuit is equal to the sum of total voltage drop in the same closed loop.
Sign Convention
Science and technology incorporate some ideas and techniques of their own to understand a system skilfully and easily. These techniques are called conventions. For example: Sign conventions of mirrors are used to understand the phenomenon of reflection and refraction in an easier way.
Step by step
Solved in 3 steps with 1 images
- Decoder circuit as shown in the following Figure. if A is LSB and C is MSB, the output expression F= YO Y Y, Y, D. Y. Decoder O a. B' O b. C O'c.B O d. CThe required 7-segmrnt decoder should have 3-inputs (which are the bits of the binary number desired to be designed, call them A,B,C), and 7 outputs (the 7 segments of the display unit which are a, b, c, d, e, f & g). 8. gf a b t la Ob d Dp e d8c Dp The 7-segment to be used is of common anode type. Consequently, any segment will be ON if its input is Low, meaning that for displaying 0 the segments inputs (a,b,c,d,e,f.g) should be (0000001), or g will be OFF while all the others are ON. 1- Make a table explaining the inputs and the corresponding outputs for the 6 combinations input (000.101), assuming the other two combinations as don't care. 2- Find the output as a function of the inputs (A,B,C) using K-map to minimize the expressions 3- Show your design using 2-input, and 3-input NAND gates, and inverter.Below is a 4-bit up-counter. What is the largest number of the counter if the initial state Q 3 Q 2 Q1Q0 =0011? (D 3 an Q 3 are MSB, and when Load = 1 and Count =1 the counter is loaded with the value D 3 ...D0) 4-bit counter Clock Q3 Load Count "I" or Vcc "I" or Vcc Do "1" or Vcc - D, Qi Q2 "0" or Gnd - D2 "0" or Gnd D3 Q3 1111 0011 1100 0110
- H.W :- 1) A four logic-signal A,B,C,D are being used to represent a 4-bit binary number with A as the LSB and D as the MSB. The binary inputs are fed to a logic circuit that produces a logic 1 (HIGH) output only when the binary number is greater than 01102-610. Design this circuit. 2) repeat problem 1 for the output will be 0 (LOW) when the binary input is less than 01112-710- Saleem LateefDesign a combinational circuit with the four inputs A,B.C, and D, and three outputs X, Y, and Z. When the binary input is odd number, the binary output is one lesser than the input. When the binary input is even number the binary output is one greate than the input. Implement the function using multiplexers with minimal input and select line.1. Use multiplexer IC's to design a combinational circuit with 3 inputs x,y, and z and three outputs A,B, and C. When the binary input is 0,1,2 or 3 the binary output is two greater than the input. When the binary input is 4,5,6, or 7 the output is three less than the input.
- (c) Figure Q3(c)(i) shows a register and Figure Q3(c)(ii) shows the input waveforms (CLOCK and Data in) to the circuit. A1 A9 A10 A2 Function generator A3 A11 A12 AS A13 A6 A14 A7 A15 Data in Bop.7) ip.r 82p.7) Logic analyser U1 U2 U3 U4 UO 6. 1. 6 1 6 INVERTER 3 CLK 3 CLK oCLK CLK 5 K K 5 K K 4027 Clock Function generator Figure Q3(c)(i) (i) Determine the type of register as shown in Figure Q3(c)(i).Q5/Find the addition result for the following operation (66)8+ (1100)EX-3+(83)10- (F2.1)16 using 2's complement, assume that the result is binary number O 1100000.0001 O 10011111.1111 O None of them O 110000010.111 O 1111101.0001Design a combinational circuit that takes 3-bit pattern as input and outputs binary code of bit position of the first 1' in the pattern reading from MSB (2nd position) to LSB (0th position).An additional output variable V is required along with binary code to indicate that the binary code is valid or note i.e., if the input pattern is '000' then the output V should be '0' to indicate that the binary code is not indicating the bit position of first 1' and we don't care about the binary code if V = 0. Design the required circuit using dual 4x1 MUXS and minimum additional logic.Available resources along with dual 4x1 MUXS are NOT gates, 2-input(AND, OR, NAND, NOR) gates.
- Design counter that counts from 00 to 59, using the IC 74LS90 ripple counter and use two 7 segment display to display the result count. You can also use 7447 binary to 7-segment Display Decoder. i need the diagram of itDesign the interfacing circuit shown below and write a program to display single digit (between 0 and 9) prime numbers followed by even numbers, the next odd numbers and repeats in 7-segment displays and its equivalent 8-bit binary value in LEDS. a) When displaying Prime numbers, the first 7-segment display must show "P" and the second 7-segment display must show prime numbers one by one b) When displaying Even numbers, the first 7-segment display must show "E" and the second 7-segment display must show even numbers one by one c) When displaying Odd numbers, the first 7-segment display must show "O" and the second 7-segment display must show even numbers one by oneA 9-bit asynchronous counter has a 128-kHz clock signal applied. (1) What is the MOD number of this counter? MOD number = (ii) What will be the frequency at the MSB output? fmsb = (iii) Assume that the counter starts at zero. What will be the count after 635 input pulses? After 635 input pulse, Count =