CLASS WORK 1: 2m 2.5 2m 1.5m 4KN 5KN 6KN A. SOLVE THE VERTICAL REACTION IN THE ROLLER SUPPORT. 4 POINTS B. SOLVE THE RESULTANT OF HORIZONTAL AND VERTICAL REACTION AT HINGE SUPPORT. 6 POINTS C. SOLVE THE AXIAL STRESS IN MEMBER BE IF ITS CROSS-SECTIONAL AREA IS 300mm². 25 POINTS 1m 3KN G H

CLASS WORK 1: 2m 2.5 2m 1.5m 4KN 5KN 6KN A. SOLVE THE VERTICAL REACTION IN THE ROLLER SUPPORT. 4 POINTS B. SOLVE THE RESULTANT OF HORIZONTAL AND VERTICAL REACTION AT HINGE SUPPORT. 6 POINTS C. SOLVE THE AXIAL STRESS IN MEMBER BE IF ITS CROSS-SECTIONAL AREA IS 300mm². 25 POINTS 1m 3KN G H

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

An assembly of bars are designed in Figure 1. The assembly is made of structural A-36 steel where bar AB and BC has a drameter of 50 mm. ASTM and 25 mm The respectively. determine дар between C and the rigid wall at D is initially 0-15 mm, the support reaction at A and D when the force P= 292 kN is applied at B 600mm 450mm 292- A B D
Frame ACGE is on hinge support at Aand E and braced at B and F to resistforce T = 18kN.a = 2 mb = 1 mc = 1 ma. Find the reaction at D in kN. b. Find the stress in brace BD if it ismade of pipe of ø = 75 mm andthickness = 6 mm. c. If brace AB is connected to BDconsist of two flat bars bolted topost AC at B using 20-mm-ø bolt,find the average shear stress (inMPa) in the bolt.
5. Bar ABD and bar CEF are connected using a pin at point C and a strut member BE to support a 9000 N load as shown below. Determine the reaction of strut member BE and determine the reaction of hinge at point F and the reaction of roller at point A. 2.5 m 2.5 m 3.5 m 1.5 m E D B C 4 m 2.5 m A F- 9000 N
The columns have the cross sectional areas as shown in the given frame using the cantilever method of analysis. 80 kN P. mL K 100 kN 6 mE F 6 m 4 m 8 m A-6250 mm? A,=5000 A-3750 mm2 A6250 mm mm? O Compute the centroid of the columns cross sectional areas from A. O Compute the horizontal shear at section N. O Compute the reaction of column at D.
The bar is snugly fit between points C and A before the loading is applied at Collar B. Assume E = 200 GPa for the steel. The circular bars in the assembly are solid. The bars are solid with a diameter of 15 mm. Assume a fixed rigid support at C and A. A C В 6 kN 3 m 2 m A) Show the FBD and compatibility equation for this problem. B) Determine the support reactions at A and C. (Horizontal forces only) Left side: Fc = Right side: FA =
1.3-3 Segments AB and BC of beam ABC are pin connected a small distance to the right of joint B (see figure). Axial loads act at A and at the mid-span of AB. A concentrated moment is applied at joint B. (a) Find reactions at supports A, B, and C. (b) Find internal stress resultants N, V, and M at 4.5 m. 136 N-m at joint B 3m 440 N A 220 N В C 6 m 3 m Pin connection PROBLEM 1.3-3
Frame ABCDE shown in Figure Q2 is supported by a fixed connection at B, roller at D and pinned at A. The frame carries 200 kN horizontal point load acting at the middle of member AC, 50 kN point load at point E and 50 kN/m uniform distributed load on member BC. El is constant. (a) (b) 2 m 2 m 50 kN/m 200 kN 6 m Figure Q2: Frame [Rajah Q2: Kerangka] 6 m 1041 Next, calculate the fixed-end moment (FEM) for all members. 50 KN 2m E For the case of no sway, calculate the value of stiffness (K) and distribution factor (DF) for each member.
The frame in the figure supports the 50-kg cylinder. Determine the reaction of the pin at A & the force of the member BC. Also, determine the factor of safety of the pin at A in shear if all pins are 10-mm in diameter & w/ an allowable shearing stress of 200MPa; and the factor of safety of member BC in axial if the cross-section of the member is a 50 x 25-mm rectangle w/ an allowable axial stress of 100MPa. Find the forces at all joints of the structure. CG & AD are tension wires. HEHE 12m Delm
1.3-3 Segments AB and BC of beam ABC are pin connected a small distance to the right of joint B (see figure). Axial loads act at A and at the mid-span of AB. A concentrated moment is applied at joint B. (a) Find reactions at supports A, B, and C. (b) Find internal stress resultants N, V, and M at 4.5 m. 136 N-m at joint B 3m 220 N 440 N 6 m 3 m Pin connection
3. Determine the reactions at the supports, then draw the moment diagram. The moment of inertia for each segment is shown in the figure. Assume A and C are rollers and B is a pin. Take E 200 GPa. 10 kN 10 KN LAB= 120(106) mm BIBC = 90(106) mm²] -4m- 4m -4m- 40 kN -6m -6m
If the load P on the beam below causes the end C to be displaced 10mm downward, determine 4. the normal strain in wires CE and BD. 4 m A B 3 m- -2m
The flanged steel cantilever beam with riveted bracket is subjected to the couple and two forces shown, and their effect on the design of the attachment at A must be determined. Replace the two forces and couple by an equivalent couple M and resultant Rat A. The couple is positive if counterclockwise, negative if clockwise. 2.05 KN Answers: M= I R-1 1.25 m 690 N-m 0.44 m KN-m 1+ 67" 10.14 m 0.14 m 1.16 KN 1) KN