compression member about its z axis, and select the correct answer from the list of the provided possible answers below. For the above, consider the data given in Figure (a). h=115mm b = 125mm Figure (a) O2.12 O 1.63 O 1.22 O 1.80 O 1.49 Design Axial Load = 14 kN O 1.41 L-3m Information: Conditions: Strength Class C24 ^₂=83.15

compression member about its z axis, and select the correct answer from the list of the provided possible answers below. For the above, consider the data given in Figure (a). h=115mm b = 125mm Figure (a) O2.12 O 1.63 O 1.22 O 1.80 O 1.49 Design Axial Load = 14 kN O 1.41 L-3m Information: Conditions: Strength Class C24 ^₂=83.15

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

05. Consider the deformable pin-jointed truss with loading, geometry and section properties as shown in the Figure Q5. Given that E=2x10"N/m, A=10mm, L=Im and P-lkN. The horizontal displacement of Joint C (in mm, up to one decimal place) is „JointC P 2AE 7. AE AE Figure 05
For the beam loaded as shown, derive the equation of the following: a. elastic curve b. slope c. deflection 250 kN В 6 m -3 m- 3 m- El = constant = 200 GPa 462 (106) mm4 E I %3D
The beam below is loaded as shown. Using double double integration method. Determine the following considering the beam properties of E-72 GPA and I = 126x10^6 mm^4 15kN 25kN 5kN 5kN 25kN/m A D G 4m- B -3m C -3m- 6m 2m LL -2m-
Using the Portal Method determine all the member forcesof the frame shown below. Submit your answers in the format where the member forces are written along the corresponding members as illustrated in the short video discussion. Computation of such values may no longer be shown. a= 7 m b= 10 m P= 116 kN ЗР/2 G H 4m P 5m a b
Q2: The simply supported beam shown as Figure 5. below is subjected to Loading as shown on the Figure. Using singularity function method. Find the maximum Lenght (L) so that the max. deflection is not greater than 30mm for the Beam.. The flexural rigidity (El) of Beam section El = 50*103 KN.m?2 “4m L Sm
The truss is made from A992 steel rods each having a diameter of 0.9 in .(Figure 1) Part A Determine the vertical displacement of joint C. Express your answer to three significant figures and include the appropriate units. ? (Ac)vert = Value Units Figure Submit Request Answer < Return to Assignment Provide Feedback C 60° 60° 12 kip 6 ft B
DESIGN OF CONTINUOUS BEAMS Design a continuous beam using the data given in the previous example. Data: fc' = 25 MPa fy = 250 MPa Main Bars = 25mm WDL = 16kN/mm WLL = 18 kN/m THAT'S ALL! A 4m RA Wu=1.4(16) + 1.7(18) = 53.kN/m Stirrups = 12mm WDL 18 kN/m WLL = 20 kN/m RB B Rc wu = 1.4(18)+1.7(20)=59.2kN/m 6m 4m Assume: 1 = LCM of Spans PULL = 51kN PLL = 30 KN
20. Situation 22. For the built-up shape shown in the figure, determine: a. The location of plastic neutral axis form the top edge of the flange in mm. ____ b. The plastic section modulus about the horizontal axis. ______ x10^6 mm^3 (3 decimal places) c. The plastic moment with bending about the vertical axis if Fy = 345 MPa. _______kN-m (rounded to the nearest whole number)
For the beam loaded as shown in the figure below, determine the following unknown using any geometric method. Consider 250 mm x 400 mm (b x h) section and E = 120 GPa. a. Deflection at C in mm. Enter absolute value only. a = 4.5m, b= 24kn/m, c = 3 5kn c kN b kN/m "a m FIGURE 5 For the beam loaded as shown in figure 5, determine the following unknown using any geometric method. Consider 250 mm x 400 mm (b x h) section and E-120 GPa. b. Slope at B in degrees, Enter absolute value only.
Calculate the value of the deflection at point B due to concentrated load P in the form ??=??????????? Note: EI will cancel out in further calculations. Enter the numerator in the answer box below in kNm3 to three decimal places. Assume the positive direction of deflection in the positive direction of v axis.
w=370 N/m 2.0 m -2.0 m R1 R2 What is the value of C1 in N.m2? Express your answer in 2 decimal places. Compute the value of Ely (N.m3) at midspan for the beam loaded as shown. Assume that downward direction is negative, upward direction is positive. Express your answer in 2 decimal places. What value of I (mm4) is required to limit the midspan deflection to 1/360 of the span if E = 10 GPa? Express your answer in 2 decimal places. Neglect the sign. w/
KAssignment 5 Problem 14.2 5 of 5 Consider the truss shown in (Figure 1). Take A = 0.0015 m² and E = 200 GPa for each member, and F = 17 kN Part A Determine the vertical deflection at joint (2 Express your answer to three significant figures and include the appropriate units. Enter negative value in the case when the deflection is downward and positive value in the case when the deflection is upward. ? Ay2 = 0.00077 Figure 1 of 1 Submit Previous Answers Request Answer F 4 m 4 m X Incorrect; Try Again; 11 attempts remaining 18 Part B 3 m 4 Determine the force in member 4 of the truss. Express your answer to three significant figures and include the appropriate units. Enter negative value in the case