Consider a beam with two 60-inch-long rods. both rods have a cross section area of 0.50 in 2 . Find the axial stress in each rod, draw the shear and moment diagrams for the beam, and find the maximum stress in the beam. Please do this without knowing the forces in the rods. it is supposed to be an indeterminate beam. Thank you

Consider a beam with two 60-inch-long rods. both rods have a cross section area of 0.50 in 2 . Find the axial stress in each rod, draw the shear and moment diagrams for the beam, and find the maximum stress in the beam. Please do this without knowing the forces in the rods. it is supposed to be an indeterminate beam. Thank you

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter6: Stresses In Beams (advanced Topics)

Section: Chapter Questions

Problem 6.2.15P: -15 A composite beam is constructed froma wood beam (3 in. x 6 in.) and a steel plate (3 in, wide)....

See similar textbooks

Similar questions

Requlred Informatlon A cantilevered beam is loaded as shown. The cross section at the wall is shown, with points of interest A (at the top). B (at the center), and C(midway between A and B). - 200 mm- 50 mm B 50 mm Cross section at wall where F= 2.2 kN NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. Calculate the magnitudes of the stresses acting on the stress elements. Do not neglect transverse shear stress. The magnitude of stresses acting on the stress elements are as follows: At element A, MPa and TA= MPa At element B. OB- MPa and T8= MPа At element C. MPa and IC= MPa
-15 A composite beam is constructed froma wood beam (3 in. x 6 in.) and a steel plate (3 in, wide). The wood and the steel are securely fastened to act as a single beam. The beam is subjected to a positive bending moment M. = 75 kip-in. Calculate the required thickness of the steel plate based on the following limit states: Allowable compressive stress in the wood = 2 ksi Allowable tensile stress in the wood = 2 ksi Allowable tensile stress in the steel plate = 16 ksi Assume that Ew= 1,500 ksi and es= 30,000 ksi.
AWT305 x 41 standard steel shape is used to support the loads shown on the beam. The dimensions from the top and bottom of the shape to the centroidal axis are shown in the sketch of the cross section. Assume LAB = 2 m, LBC= 5 m, LcD = 1 m, PA = 12 kN, WBC = 12 kN/m. Consider the entire 8-m length of the beam and determine: (a) the maximum tension bending stress or at any location along the beam, and (b) the maximum compression bending stress oc at any location along the beam. A PA LAB Answers: (a) OT = (b) oc = B i 62.19 i 25.81 WBC LBC 1 WT305 x 41 C LCD 88.9 mm 211.1 mm MPa. MPa. D x
AWT305 x 41 standard steel shape is used to support the loads shown on the beam. The dimensions from the top and bottom of the shape to the centroidal axis are shown in the sketch of the cross section. Assume LAB = 3 m, LBc = 7 m, LCD = 2 m, PA = 17 kN, WBC = 10 kN/m. Consider the entire 12-m length of the beam and determine: (a) the maximum tension bending stress or at any location along the beam, and (b) the maximum compression bending stress oc at any location along the beam. PA LAB Answers: (a) σT = (b) oc = i i B WBC LBC LCD Ť WT305 x 41 88.9 mm 211.1 mm MPa. MPa. D
AWT305 x 41 standard steel shape is used to support the loads shown on the beam. The dimensions from the top and bottom of the shape to the centroidal axis are shown in the sketch of the cross section. Assume LAB = 3 m, LBC= 6 m, LCD= 4 m, PA = 10 kN, WBC = 7 kN/m. Consider the entire 13-m length of the beam and determine: (a) the maximum tension bending stress or at any location along the beam, and (b) the maximum compression bending stress oc at any location along the beam. A PA LAB B WBC LBC T WT305 x 41 LCD ↑ 88.9 mm. 211.1 mm D X
AWT305 x 41 standard steel shape is used to support the loads shown on the beam. The dimensions from the top and bottom of the shape to the centroidal axis are shown in the sketch of the cross section. Assume LAB = 3 m, LBc = 7 m, LcD = 1 m, PA = 9 kN, WBC = 11 kN/m. Consider the entire 11-m length of the beam and determine: (a) the maximum tension bending stress or at any location along the beam, and (b) the maximum compression bending stress oc at any location along the beam. A PA LAB B WBC LBC C Z + WT305 x 41 LCD 88.9 mm 211.1 mm X
M=23 kip*ft 4 kip Y-direction for roller? 5 ft 3 ft 9 kip X-direction for the pinned support (triangle)? 3 ft Y-direction for the pinned support (triangle)? 2 ft For the beam above, what are the support reaction forces? Please report your answers in the units of 'kips' and to 2 significant digits (i.e. two decimal places). 6 in 9 in
A WT305 x 41 standard steel shape is used to support the loads shown on the beam. The dimensions from the top and bottom of the shape to the centroidal axis are shown in the sketch of the cross section. Assume LAg - 2 m, Lac- 7 m, Lco- 4 m, PA- 14 kN, Wac- 8 kN/m. Consider the entire 13-m length of the beam and determine: (a) the maximum tension bending stress or at any location along the beam, and (b) the maximum compression bending stress oc at any location along the beam.
A WT305 x 41 standard steel shape is used to support the loads shown on the beam. The dimensions from the top and bottom of the shape to the centroidal axis are shown in the sketch of the cross section. Assume LAB = 3 m, LBc = 7 m, LcD = 2 m, PA = 17 kN, WBC = 10 kN/m. Consider the entire 12-m length of the beam and determine: (a) the maximum tension bending stress or at any location along the beam, and (b) the maximum compression bending stress oc at any location along the beam. PA LAB Answers: (a) 07 = (b) oc= B 287.45 121.1 WBC LBC WT305 x 41 MPa. LCD क 88.9 mm 211.1 mm MPa. X
The capacity of the fixed-fixed beam 3-4 needed to be increased. It was decided that this can be achieved by attaching three truss members (1-2, 1-3 and 1-4, all of the same cross section) to the beqm, as shown in the sketch below. The width of the beam is b, its height h=3b, its length 2L=20h. The load on the beam is q=const. What should the minimum cross-section area of the truss members be for the transverse displacement of the beam at point 2 to be no larger than half of the original beam's displacement (i.e. without the truss members). Assume that the material of the beam and of the truss members is the same. 3 4 2 L/2 1
The beam in Figure 1; (a) Draw the Normal Force Diagram. (b) Draw the shear force diagram. (c) Draw the bending moment diagram. şekil 1 = figure 1 L1(m)=1.0 , L2(m)=1.4 , L3(m)=1.2 , M(kN.m)=20 , P(kN)=9 , q(kN/m)=8
From the given beam shown below, compute the following: 20 mm 80 mm 160 mm NA 1.0 m 1.0m H– 20 mm 1. Distance between top of the beam to Neutral Axis or "c top". 2. Moment of Inertia at Neutral Axis or "I" 3. What is the maximum safe value of P if the working stress in shear is 6 MPa? 4. Using the maximum safe value of P what is the Maximum shear? 5. Using the maximum safe value of P what is the Maximum Moment?