Consider a bracket subjected to a 1400 N load and a 800 Nload, as depicted in the accompanying figure. Find the value ofthe angle θ between the forces such that the resultant R has amagnitude of 2000 N. Furthermore, find the angle β between Rand the 1400 N load Q2Consider a bracket subjected to a 1400 N load and a 800 Nload, as depicted in the accompanying figure. Find the value ofthe angle O between the forces such that the resultant R has amagnitude of 2000 N. Furthermore, find the angle Bbetween Rand the 1400 N load.1400 N800 N

Answered: Image /qna-images/answer/e26cea2a-9ae0-47d4-affb-103a2a155ef6.jpg

Consider a bracket subjected to a 1400 N load and a 800 N load, as depicted in the accompanying figure. Find the value of the angle θ between the forces such that the resultant R has a magnitude of 2000 N. Furthermore, find the angle β between R and the 1400 N load

Consider a bracket subjected to a 1400 N load and a 800 N load, as depicted in the accompanying figure. Find the value of the angle θ between the forces such that the resultant R has a magnitude of 2000 N. Furthermore, find the angle β between R and the 1400 N load

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter2: Axially Loaded Members

Section: Chapter Questions

Problem 2.2.21P: Solve the preceding problem for the following data: b = 8.0 in., k = 16 lb/in., a = 45°, and P = 10...

See similar textbooks

Related questions

Q: Which of the following would NOT be cause for rejection when checking the power steering system? Sy...

A: Given : Which of the following would NOT be cause for rejection when checking the power steering sys...

Q: Sment č Drpm for

Q: A titanium cylinder having a diameter of 50 mm in diameter and 540 mm long falls inside a vertical t...

Q: e mean speed of the flywheel

A: Given; A flywheel of moment of inertia, I= 9.8 kg m3It fluctuates by 30 rpmor, N1-N2=30 rpmfluctuate...

Q: The vacuum at the steam inlet to a condenser was found to be 716 mm of Hg and the temperature of ste...

Q: 8. The potential energy of an apple is 6.00 joules. The apple is 3.00-meters high. What is the mass ...

Q: In a palm oil processing plant, the crude oil is heated using hot water from a furnace. The furnace ...

A: Heat exchangers are devices that allow heat to be transferred between two fluids via a separating wa...

Q: nd a viscous damper. a) Derive the equation of motion for the block, assuming that x is measure om t...

Q: If the journal bearings at A and B exert only horizontal and vertical forces on the shaft, determine...

Q: Nitrogen gas at 15 oC has a density of 0.07616 lbm/ft3 with a kinematic viscosity of .146 cm2 /s for...

A: The fluid's inherent persistence or viscosity causes boundary layers to form. When a fluid flows acr...

Q: knife follower motion interval described below: 1. To raise the valve through 50 mm during 120° rota...

Q: In a Parson turbine running at 1500 RPM the available enthalpy drop for expansion is 62.8 kJ/kg. If ...

A: A reaction turbine, also known as a Parsons turbine, is a turbine having moving nozzles that alterna...

Q: - The bucket of a 'bobcat" is lifted and tilted by means of hydraulic cylinders EL and HJ Figure P4-...

Q: What is the stress concentration factor for a part under axial load with a shoulder fillet if d=1.5"...

Q: 2- A compound shaft consists of two segments. Segment (1) is a tube with a length of L, = 500 mm, an...

Q: For the crank- slide mechanism. B slides 03 along 0203 link making 300mm stroke, as shown in Figure....

Q: Magnetic resonance imaging (MRI) is a medical imaging technique that located in hospitals and radiol...

A: Any product, gadget, implant, or equipment that provides no known dangers in the MRI environment...

Q: A francis turbine is having a inlet diameter of 2.0 m and an outlet diameter of 1.2 m. The breath of...

A: Inlet diameter di=2 m ,Outlet diameter d0=1.2 mb=.2 m N=250 rpmQ=8 m3/sec

Q: Traveling with an initial speed of vo 53 km/h, a car accelerates at 3,259 km/h along a straight road...

Q: An ideal otto cycle operates with a temperature of 370 deg. C at the end of the compression process...

Q: of degrees of fre sm shown below

Q: A cylinder rests on the 90° corner as shown. The tension P in the string is gradually increased unti...

Q: potential energy A diver at the top of a 10.0 m high diving platform has a mass of 50.0kg. What is h...

A: Given data : Mass=m height=h Acceleration due to gravity=g To find : Potential energy

Q: V. V. 6R „Linear velcity distribution V. V.

A: As the flow approaches to the sphere, when it encountered sphere it will slides over it. but at the ...

Q: Q3. Audi’s design of their R8 model is designed in order to have the engine in the rear of the car w...

A: Audi R8 is RWD Giving explanation and definition.

Q: 1. In the given figure, gear 1 has 24 teeth and gear 2 has 70 teeth of PD=4. Gear 3 has 20 teeth and...

Q: Solve the following problems. Be sure to show your work. Answer without work shown will receive no c...

A: Drawing equivalent load diagram. and calculated magnitude and location of the resultant force with r...

Q: Two bars are used to support a load P. When unloaded, AB is 5 in. long, AC is 8 in. long, and the ri...

Q: Use rotation about the fixed frame to calculate the transformation matrix for a rotation of 30° abou...

A: Case (1), θ=30° rotaion about z0 axisRzθ=cos30°-sin30°0sin30°cos30°0001Rzθ=.866-.50.5.8660001

Q: 2/73 The bracket is fastened to the girder by means of the two rivets A and B and supports the 2-kN ...

Q: What is the kinetic energy of a 3-kilogram ball that is rolling at 2 meters per second?

A: Given data : Mass of ball =m Velocity of ball=V To find : Kinetic energy

Q: Four forces are applied at a point in a body. Determine the magnitude of the resultant R of the four...

Q: Osing tensor notahan expand the equaton Let Ye =aijXs = lij zj

A: For solution refer below images.

Q: A trolley that moves along a horizontal beam is acted upon by two forces as shown (a) knowing that a...

Q: a) The total strain energy for a bar of length L. is given by the equation -J. 2EA. How would the eq...

A: we have to determine the effect of making the bar tapered.

Q: The vacuum at the steam inlet to a condenser was found to be 716 mm of Hg and the temperature of ste...

A: The vacuum efficiency is ηvacuum = 99.7%.

Q: Sprayer has 3 m used to spray 30 ha, speed 0.97 m/s, field efficiency 75%, The sprayer uses 75% of i...

A: Sprayer b= 3 mSpray area A=30 haV=.97 m/secηfield=.75Sprayer uses 75% of its width

Q: Slider block A moves to the left with a constant velocity of 6 m/s. Determine (a) the velocity of bl...

A: Given:VA=6 m/s

Q: Consider an actual regenerative Rankine cycle with one open feed water heater. For each kg steam ent...

A: Find the specific enthalpy of saturated liquid leaving the heater

Q: ne tension in each cable ir

A: To determine the tension in each cable.

Q: (i) Process average and control limits.

Q: - A circular shaft is subjected to a torque 'T and a bending moment M. The ratio of maximum shear st...

A: Find the ratio of maximum shear stress to maximum bending stress.

Q: When checking the front end, which of the following are NOT cause for rejection

A: Answer = option (c) All of the statements shown are cause for rejection

Q: 3. 5 kg air with initial temperature of 100°C expands at a constant pressure of 2 bar to reach to a ...

A: (A) Work done in the process, WD = 464.74 kJ. (B) Heat supplied for expansion process, Q = 1627.39 k...

Q: The 5.5kg block hits the spring with a speed of 3.9m/s. Determine the total distance traveled by the...

A: Given data: m=5.5 kgv=3.9 m/sk=2.7 N/m Need to determine the total distance traveled by the block b...

Q: Figure P13.11 shows a mechanism that raises pack- ages in a transfer mechanism. If a 100-N package s...

Q: Cooling water leaves at 35ºC and at 100 kg/s from the condenser of a thermal power station and enter...

Q: A Strain gage W NA A L b Side view Lo Front view A cantilever beam has the following parameters: Lo ...

Q: Under the right conditions, it is possible, due to surface tension, to have metal objects float on w...

Q: A 200g of copper calorimeter contains 400g of water at 30⁰C. It is stirred by paddles rotated by app...

Concept explainers

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.

Question

Consider a bracket subjected to a 1400 N load and a 800 N
load, as depicted in the accompanying figure. Find the value of
the angle θ between the forces such that the resultant R has a
magnitude of 2000 N. Furthermore, find the angle β between R
and the 1400 N load

Q2
Consider a bracket subjected to a 1400 N load and a 800 N
load, as depicted in the accompanying figure. Find the value of
the angle O between the forces such that the resultant R has a
magnitude of 2000 N. Furthermore, find the angle Bbetween R
and the 1400 N load.
1400 N
800 N

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Find the internal force systems acting on sections 1 and 2.
Q3 Find the resultant of force Y 390 lb MATHalino.com 12 30 1 300 Ib 722 lb Figure P-265 5n
4. Forces F =F-20N and the third force F3 25N act on a cube with the side of a=2m. a. Find the screw driver (wrench) that is created by these forces i.e pitch, Mparallel, Mpapendicular b. Find the point of intersection of the axis of the wrench with the x-y plane. How do you check your answer is correct? G F D A B.
Hello, can someone help me w this pls. Find the internal forces at point J. Data: the length of X(mm) its 237, and the length on Y(mm) its 175. The angle α is worth 30°.
Find the values of P and F so that the four forces shown in the figure will produce an upward resultant of 300lbs acting 4ft from the left end of the bar?
A tower of 20 m, height is supported by three ropes shown in figure below. If the force of AB Is 50 N, find the force of AC and AD so that the resultant force should be vertical. A (0, 20, 0) Fa 20 m D(-8.0. 0) 50 N C (8,0, -10) B (8. 0, 5)
A tower has a wire (AB) attached to the tower at point B and it is anchored to a bolt at A. The tension in the wire is 993 N. Call the Force in AB FAB Calculate the x, y and z components of FAB What is the direction of FAB in terms of alpha ⍺, beta β and gamma ? ? What is the x component of FAB ? Round your answer to the nearest whole number. What is the y component of FAB ? Round your answer to the nearest whole number. What is the z component of FAB ? Round your answer to the nearest whole number. What is alpha ⍺ for FAB ? Enter answer rounded to one decimal place. What is beta β for FAB ? Enter answer rounded to one decimal place. What is gamma ? for FAB ? Enter answer rounded to one decimal place.
Find the tension in each of the supporting cables in the figure when the weight of the crate is 500 newtons.
Find the value of C & D so that the four forces shown in Figure produce an upward resultant of 300lb acting at 4ft from the left end of the bar. Where: A = 100kN and B = 200KN 2' C 3' D 2' B Show your complete solution and Tabulate your answer. Answer with text and/or attachments:
The cantilever beam is loaded with 2 forces as shown below. The force F is 33 N. The force G is 5 N. If the beam was instead loaded with one force H in such a way that the loading was equivalent, then what the would the distance d need to be in m? The positive values of H and d are shown, but either value may be negative. A 2m ➜ Im B F C A d 2m B H C
(٢٦+ * Find the two forces Fbc & Fac as :shown in the figure below Fab=30 N 110 30/Fbc (Fbc=45.18 N and Fac= 58.8 N) O (Fbc=38.56 N and Fac= 56.38N) O (Fbc=75.18 N and Fac= 78.8 N) O ! Fac
The post weighing 1500 lbs is to just be vertically pulled out of the ground using two ropes as shown in the figure. One rope is subjected to a force of 600 lb and is directed at 60° from the horizontal. Determine the angle 0 (degrees). 600 Ib 60°