Consider a medium in which the heat conduction equation is given in its simplest form as r? ar Or k 1. Is heat transfer steady or transient? 2. Is heat transfer one-, two-, or three-dimensional? 3. Is there heat generation in the medium? 4. Is the thermal conductivity of the medium constant or variable?

Consider a medium in which the heat conduction equation is given in its simplest form as r? ar Or k 1. Is heat transfer steady or transient? 2. Is heat transfer one-, two-, or three-dimensional? 3. Is there heat generation in the medium? 4. Is the thermal conductivity of the medium constant or variable?

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter1: Basic Modes Of Heat Transfer

Section: Chapter Questions

Problem 1.10P: 1.10 A heat flux meter at the outer (cold) wall of a concrete building indicates that the heat loss...

See similar textbooks

Similar questions

A plane wall of thickness 2L has internal heat sources whose strength varies according to qG=qocos(ax) Where qo is the heat generated per unit volume at the center of the wall (x=0) and a is a constant. If both sides of the wall are maintained at a constant temperature of Tw, derive an expression for the total heat loss from the wall per unit surface area.
1.63 Liquid oxygen (LOX) for the space shuttle is stored at 90 K prior to launch in a spherical container 4 m in diameter. To reduce the loss of oxygen, the sphere is insulated with superinsulation developed at the U.S. National Institute of Standards and Technology's Cryogenic Division; the superinsulation has an effective thermal conductivity of 0.00012 W/m K. If the outside temperature is on the average and the LOX has a heat of vaporization of 213 J/g, calculate the thickness of insulation required to keep the LOX evaporation rate below 200 g/h.
A plane wall 15 cm thick has a thermal conductivity given by the relation k=2.0+0.0005T[W/mK] where T is in kelvin. If one surface of this wall is maintained at 150C and the other at 50C, determine the rate of heat transfer per square meter. Sketch the temperature distribution through the wall.
1.77 Explain each in your own words. (a) What is the mode of heat transfer through a large steel plate that has its surfaces at specified temperatures? (b) What are the modes when the temperature on one surface of the steel plate is not specified, but the surface is exposed to a fluid at a specified temperature?
2.15 Suppose that a pipe carrying a hot fluid with an external temperature of and outer radius is to be insulated with an insulation material of thermal conductivity k and outer radius . Show that if the convection heat transfer coefficient on the outside of the insulation is and the environmental temperature is , the addition of insulation actually increases the rate of heat loss if , and the maximum heat loss occurs when . This radius, is often called the critical radius.
5.10 Experiments have been performed on the temperature distribution in a homogeneous long cylinder (0.1 m diameter, thermal conductivity of 0.2 W/m K) with uniform internal heat generation. By dimensional analysis, determine the relation between the steady-state temperature at the center of the cylinder , the diameter, the thermal conductivity, and the rate of heat generation. Take the temperature at the surface as your datum. What is the equation for the center temperature if the difference between center and surface temperature is when the heat generation is ?
Discuss the modes of heat transfer that determine the equilibrium temperature of the space shuttle Endeavour when it is in orbit. What happens when it reenters the earths atmosphere?
2.29 In a cylindrical fuel rod of a nuclear reactor, heat is generated internally according to the equation where = local rate of heat generation per unit volume at r = outside radius = rate of heat generation per unit volume at the centerline Calculate the temperature drop from the centerline to the surface for a 2.5-cm-diameter rod having a thermal conductivity of if the rate of heat removal from its surface is 1.6 .
1.10 A heat flux meter at the outer (cold) wall of a concrete building indicates that the heat loss through a wall of 10-cm thickness is . If a thermocouple at the inner surface of the wall indicates a temperature of 22°C while another at the outer surface shows 6°C, calculate the thermal conductivity of the concrete and compare your result with the value in Appendix 2, Table 11.
A hot water pipe is 100 mm in diameter and 80 m long. This pipe is insulated in two layers. First layer is 25 mm thick, thermal conductivity is 0.12 W/m C material, second layer is 45 mm thick It is made of material with a thermal conductivity of 0.05 W/m C. T1, T2 and T3 are the surface temperatures in the pipe. One With the acceptance of heat transfer in dimensional and continuous conditions, transfer from the pipe in case T1= 600 OC and T3= 35 C Find the amount of heat released and the temperature T2. 2.tabaka 1.tabaka 100 mm T₁ T₂ T3
Drive an expression for heat transfer and temperature distribution for steady state one dimensional heat conduction in a plan wall. The temperature is maintained at a temperature Ti at x=0, while the other face X-L is maintained at temperature T2, the thickness of the wall may be taken as L and the energy equation is given by: d²T/dx² = 0. : Sketch a simple diagram for the temperature distribution in plane wall for a steady state one dimensional heat conduction, with heat generation. The surface temperature of the walls Ti and T2, for the cases Ti>T2, T1-T2, and T2>T1. The thickness of the wall may be taken as 2L
Which formula is used to calculate the heat conduction in the AXIAL direction in a vertically located pipe segment whose inner and outer surfaces are perfectly insulated. Here r, is inner radius, r, outer radius, Tri pipe inner surface temperature, Tro pipe outer surface temperature, L is the length of the pipe, T the temperature on the lower surface, Ty the temperature on upper surface. Tu r; Tro r