Consider a rectangular plate shown in Figure 1 and is subjected to a compressive stress of 2.5 MPa in the long direction and a tensile stress of 12.0 MPa in the short direction. Determine the normal stress ow acting perpendicular to the line of the weld and the shear stress tw acting parallel to the weld. (Assume that the normal stress ow is positive when it acts in tension against the weld and the shear stress tw is positive when its acts counterclockwise against the weld). 12.0 MPa Weld 100 mm 250 mm 2.5 MPa

Consider a rectangular plate shown in Figure 1 and is subjected to a compressive stress of 2.5 MPa in the long direction and a tensile stress of 12.0 MPa in the short direction. Determine the normal stress ow acting perpendicular to the line of the weld and the shear stress tw acting parallel to the weld. (Assume that the normal stress ow is positive when it acts in tension against the weld and the shear stress tw is positive when its acts counterclockwise against the weld). 12.0 MPa Weld 100 mm 250 mm 2.5 MPa

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A rectangular plate (0 =25°) is formed by welding two triangular plates shown in figure. The plate is subjected to a compressive stress of 2.5 MPa in the x-direction and a tensile stress of 15 MPa in the y-direction. Determine the normal stress acting perpendicular to the line of the weld and the shear stress acting parallel to the weld. y Weld Lütfen birini seçin: a. 0.417 MPa/4.38 MPa b. None O c. 0.6256 MPa/6.70 MPa O d. 11.874 MPa/6.70 MPa e. 9.3175 MPa/6.09 MPa O O O
A rectangular plate (0 =25°) is formed by welding two triangular plates shown in figure. The plate is subjected to a compressive stress of 2.5 MPa in the x-direction and a tensile stress of 15 MPa in the y-direction. Determine the normal stress acting perpendicular to the line of the weld and the shear stress acting parallel to the weld. Lütfen birini seçin: a. 9.3175 MPa/6.09 MPa b. None c. 0.417 MPa/4.38 MPa d. 0.6256 MPa/6.70 MPa e. 11.874 MPa/6.70 MPa
Asap
A rectangular plate (0 =23°) is formed by welding two triangular plates shown in figure. The plate is subjected to a compressive stress of 2.3 MPa in the x-direction and a tensile stress of 13 MPa in the y-direction. Determine the normal and the shear stresses acting parallel to the weld. Weld Lütfen birini seçin: a. 10.664 MPa/5.50 MPa b. 0.3131 MPa/4.93 MPa c. None d. 0.0358 MPa/5.50 MPa e. 9.3175 MPa/6.09 MPa
A rectangular plate (0 =21°) is formed by welding two triangular plates shown in figure. The plate is subjected to a compressive stress of 2.9 MPa in the x-direction and a tensile stress of 19 MPa in the y-direction. Determine the normal stress acting perpendicular to the line of the weld and the shear stress acting parallel to the weld. Wekd
A rectangular plate (0 =20°) is formed by welding two triangular plates shown in figure. The plate is subjected to a compressive stress of 2.0 MPa in the x-direction and a tensile stress of 10 MPa in the y-direction. Determine the normal and the shear stresses acting parallel to the weld. y Weld Lütfen birini seçin: a. -0.417 MPa/4.38 MPa O b. 9.3175 MPa/5.50 MPa O c.-0.596 MPa/3.85 MPa d. None e. 8.5962 MPa/3.85 MPa
Cal culate the stress between the two rods at the weld if the weld has a radius of 0.5 inch and the of the small area rod is 1" x 1.5" and T= 50 Kips %3D Calculate the stress at the cross averaye 0.5 diameter hole in the. section of the wider 1.5" x 2.5" rod, then calculate the stress concentration Mer around the 0.5" Diameter hole due to the 50 Kips Tensile force.
are of 10 mm size and the weld length is 30 mm. loading F as shown in figure. Both legs of the fillets considering the minimum throat of the weld, the A fillet welded joint is subjected to transverse loading Fas shown in figure. Both legs of the fillets ere of 10 mm size and the weld length is 30 mm. If the allowable shear stress of the weld is 94 MPa, considering the minimum throat of the weld, the maximum allowable transverse load in kN is F
Problem 1: A cylindrical pressure vessel with an inner radius of 1.25 m and a wall thickness of 21 mm is subjected to an internal pressure of 8 MPa. Find the normal stress and shear stress along the 45° weld seam. 45° -1.25 m
Oy nüz aplanmadı Ot D üzerinden etlenmiş Txy Soruyu etle Tnt Ox On n (a) (b) On the surface of a structural member, stresses are given as Ox=67,9 MPa, oy=25,5 MPa and Txy=-24,3 as shown in figure (a). Determine the maximum principal stress (MPa). Note: If the stress is compressive, use - sign. Yanıt:
A rectangular plate (θ =25°) is formed by welding two triangular plates shown in figure. The plate is subjected to a compressive stress of 2.5 MPa in the x-direction and a tensile stress of 15 MPa in the y-direction. Determine the normal stress acting perpendicular to the line of the weld and the shear stress acting parallel to the weld.
1 m Section of connection for AB and BC 1m An elbow shaped frame made of Al 2024 T6 aluminum has a circular cross-section having a radius of 5mm. a. Take a cut through the section where the AB and BC segments are connected (shown in the figure at point B). Define the stress types that will occur on this section as a result of loading on the frame and show the variation of these stresses on the cross-section. b. Drawing a free body diagram, show and calculate the internal loads at point C. Show the stress distribution that are caused by these internal loads on this cross-section. Do the internal loads vary along the beam BC ?