Consider a regenerative cycle using steam as the working fluid. Steam leaves the boiler and enters the turbine at 4 MPa, 400°C. After expansion to 400 kPa, some of the steam is extracted from the turbine to heat the feedwater in an open FWH. The pressure in the FWH is 400 kPa, and the water leaving it is saturated liquid at 400 kPa. The steam not extracted expands to 10 kPa. Draw the T-S diagram and determine the cycle efficiency. Boiler Turbine ·b· Pump Foodwater heater •b Pump Condenser

Consider a regenerative cycle using steam as the working fluid. Steam leaves the boiler and enters the turbine at 4 MPa, 400°C. After expansion to 400 kPa, some of the steam is extracted from the turbine to heat the feedwater in an open FWH. The pressure in the FWH is 400 kPa, and the water leaving it is saturated liquid at 400 kPa. The steam not extracted expands to 10 kPa. Draw the T-S diagram and determine the cycle efficiency. Boiler Turbine ·b· Pump Foodwater heater •b Pump Condenser

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Steam enters the turbine at 10 MN/m2and 450oC. The steam expanded in the turbine down to the condenser pressure of 20 kN/m2. The condensate leaving the condenser is pumped to the boiler pressure directly. The turbine has an isentropic efficiency of 89%, and the mass of steam generated in the boiler is 5 kg/s. Find: Cycle thermal efficiency. Plant power output.Neglect the pump work and draw the cycle on a T – s diagram. Hint: 1 MN/m2= 10 bar
A flashed steam geothermal power plant is located where underground hot water is available as a saturated liquid at 700 kPa. The well head pressure is 600 kPa. The flashed steam enters the steam turbine at 500 kPa and expands to 15 kPa when it is condensed. The flow rate from the well is 29.6 kg/s. Determine the cycle thermal efficiency of the plant in %.
inlet of the high-pressure turbine. the 10-99 A tcxtile plant requires 4 kg/s of saturatcd steam at 2 MPa, which is extracted from the turbinc of a cogenera- tion plant. Steam enters the turbine at 8 MPa and 500°C at a rate of 11 kg/s and leaves at 20 kPa. The extracted steam leaves the process heater as a saturated liquid and mixes with the feedwater at constant pressure. The mixture is pumped to the boiler pressure. Assuming an isentropic efficiency of 88 percent for both the turbine and the pumps, deter- mine (a) the rate of process heat supply, (b) the net power output, and (c) the utilization factor of the plant. Answers: (a) 8.56 MW, (b) 8.60 MW, (c) 53.8 percent Turbine F Boiler Process heater Condenser (3) Pump II Pump I FIGURE P10-99
Consider an ideal Rankine cycle utilizing steam. Steam leaves the boiler and enters the turbine at 0.5 MPa, 400 oC. Then the steam is expanded in turbine to 10 kPa. Determine the cycle efficiency
In a reheat cycle steam at 15 MPa, 540 degrees Celsius enters the engine and expands to 1.95 MPa. At this point the steam is withdrawn and passes through a reheater. It reenters the engine at 540 degrees Celsius. Expansions now occur to the condenser pressure of 0.0035 MPa. Find the efficiency.
Steam is delivered to turbine at 5.4 Mpa and 600C. Before condensation at 31C, steam is extracted for feedwater heating at 0.6 Mpa. For an ideal regenerative cycle, find the thermal efficiency. (Attach your T-S and schematic diagram of this problem)
In a Rankine cycle, steam leaves the boiler and enters the turbine at 4 MPa and 400◦C. The condenser pressure is 10 kPa. Determine the cycle efficienc
A flashed steam geothermal power plant is located where underground hot water is available as a saturated liquid at 700 kPa. The well-head pressure is 600 kPa. The flashed steam enters the steam turbine at 500 kPa and expands to 15 kPa when it is condensed. The flow rate from the well is 29.6 kg/s. Determine the cycle thermal efficiency of the plant in %. If the steam table is needed, please use the green book entitled "Thermodynamics Properties of Water Including Vapor, Liquid, and Solid Phases" by Keenan, Keyes, Hill, and Moore.
A steam powerplant operates on a rankine cycle the steam enters the turbine at 7 mpa 550°c with a velocity of 3m/s . Its dischaRge to the condenser at 20kpa with the velocity of 90m/s calculate the network in kw for a flow of 37.8kg/s
Consider a steam plant operating on the ideal Rankine cycle. Steam enters the turbine at 3 MPa and 350°C and is condensed in the condenser at a pressure of 10 kPa. Determine The thermal efficiency if steam is superheated to 600°C instead of 350°C in %. Include your T - S diagram on your solution SI unit plsss thankyou
Steam is delivered to turbine at 5.4 MPa and 600 degree C. Before condensation at 31 degree C, steam is extracted for feed water heating at 0.6 MPa. The turbine exhaust is 60 degree C. the required values of some state point properties are tabulated below. 9. Calculate the total pump work of the cycle
A power plant operating in a Reheat Rankine Cycle produces steam at 3 MPa, 600oC in the boiler. It keeps the condenser at 45oC by transfer of 10 MW out as heat transfer. The first turbine section (high-pressure) expands to 500 kPa and then flow is reheated followed by the expansion in the low-pressure turbine. Provide a detailed solution. Avoid shortcuts. Determine the mass flow rate (kg/s)