Consider a simple positive phase sequence, three-phase, three-wire system operated at 50 Hz and with a balanced loa Each phase voltage of 240 V is connected across a load composed of a series-connected 80.00 and 500 mH combination. Please report your answer, so the magnitude is positive, and all angles are in the range of negative 360 degrees to positive 360 degrees. Calculate the total power supplied by the three-phase source. (Round the final answer to three decimal places.) W. The total power supplied by the three-phase source is

Consider a simple positive phase sequence, three-phase, three-wire system operated at 50 Hz and with a balanced loa Each phase voltage of 240 V is connected across a load composed of a series-connected 80.00 and 500 mH combination. Please report your answer, so the magnitude is positive, and all angles are in the range of negative 360 degrees to positive 360 degrees. Calculate the total power supplied by the three-phase source. (Round the final answer to three decimal places.) W. The total power supplied by the three-phase source is

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter6: Power Flows

Section: Chapter Questions

Problem 6.61P

See similar textbooks

Similar questions

1. A load of 50 ohms resistance and 0.4 H inductance are connected in series to 100 volts, 60 hz a-c source. What must be the value of the capacitance to be connected in parallel to the circuit to raise the power factor to 0.96 lagging. Draw the circuit diagram.
The circuit shows an unbalanced electrical installation powered by a positive sequence symmetrical three-phase network of 380 V compound voltage. The loads are single phase. Load 1 absorbs an active power of 950 W with f.d.p. 0.5 inductive. Load 2 absorbs an active power of 1,140 W with f.d.p. Unit. Load 3 absorbs from the network an active power of 760 W with f.d.p. 0.5 capacitive. Taking the network voltage URN as the phase reference, calculate: a) complex expressions of the line currents IR. Is. and IT
Two impedances consist of resistance of (15 ohms and series connectedinductance of 0.04 henry) and (resistance of 10 ohms, inductance of 0.1 henryand a capacitance of 100 microfarad, all in series) are connected in series andare connected to 230 volts, 50 – Hz AC source. Find: (a) current drawn, (b) voltageacross each impedance, (c) individual and total power factor. Draw the phasordiagram.
The circuit shows an unbalanced electrical installation powered by a positive sequence symmetrical three- phase network of 380 V compound voltage. The loads are single phase. Load 1 absorbs an active power of 950 W with f.d.p. 0.5 inductive. Load 2 absorbs an active power of 1,140 W with f.d.p. Unit. Load 3 absorbs from the network an active power of 760 W with f.d.p. 0.5 capacitive. Taking the network voltage URN as the phase reference, calculate: a) complex expressions of the line currents IR. Is. and IT RO- SO TO IR Is IT U₁-380 V CARGA 1 P₁ =950 W cos p1=0,5 ind. CARGA 2 P₂=1.140 W cos p₂=1 CARGA 3 P3=760 W cos p3=0,5 cap.
Which cannot be said since Z is an inductive load in the circuit given below? A) load voltage period is 0.02sec. B) Load voltage peak value is 311V. C) Load voltage frequency is 50Hz D) Load voltage average value is 220V.
Task 3 A three phase, four wire star connected load consisting of: ZR: a resistor of 9500 in series with a 3H inductor ZB: a resistor of 1950 ZY: a resistor of 1950 in series with a 4µF capacitor Using the equipment available in the power lab (Room T017), connect the given load to a three-phase supply available in the lab and: 3.1. Determine the current of each line and the neutral current and measure the total power supplied by the source. 3.2. Analytically, calculate all currents and the total power and compare with those obtained in measurements. 3.3. Device a method and measure the waveform of the neutral current. Discuss the obtained waveform and the reason for any distortion in the waveform 3.4. Validate your calculations using computer simulation
Calculate the value of capacitance in the following figure that must be connected in parallel with the load to correct the source power factor to 0.94 lagging. The frequency f = 60 Hz
A utility company plans to connect a total of 20uF of capacitance to a 7200 volt line. To make this connection four capacitors will be connected in series. What is the capacitance of each capacitor? Answer is 80uF. What is the minimum AC voltage rating of each capacitor? Answer is 1200 volts. What is the current flow through the circuit? And what is the minimum kVAR rating of each capacitor?
Please show you detailed solution Number 10 A voltage of 250 volts at 50 Hz is impressed on a circuit having a 60-ohm resistor, 35-?F capacitor, and a 0.25-henry inductor in series. Determine power factor. A. 0.979 C. 0.924 B. 0.862 D. 0.707
Three load units A, B and C are connected in parallel and take currents that are respectively 12, 10 and 15 amperes. Assuming IA to be the reference phasor, IB leads IA by 30°, and IC lags IA by 65°, calculate the total current and the angle it makes with the reference.
In a series AC resistive circuit: a) voltage leads current by 90°(degrees). O b) current leads voltage by 90°(degrees). © current and voltage are in phase. d) d current and voltage cancel.
The figure shows a 3-phase bala Time left 1:06:30 200 /00 Vrms. sequence electrical system. Vcn Vbn %3D al Balanced (-) sequence 100 so a 2000 Vms Select one: O a. 200 /-120 Vrms O b. 200 v2 /0 Vrms O C. 200 /0 Vrms O d. 200 v2/-120 Vrms e. 200/120 Vrms