Consider an RC beam cross section as shown below 300.mm 540 mm 50 mm 93. Determine the depth of the stress block a. 174.9 mm b. 147.9 mm 94. Determine the nominal moment capacity a. 411 kNm b. 445 kNm 95. Determine the depth of the neutral axis a. 121.54 mm b. 211.45 mm 96. Determine the nominal moment capacity As = 4,500mm² fy = 275 MPa f = 27 MPa c. 179.4 mm 197.4 mm d. c. 495 kNm d. 454 kNm c. 245.11 mm d. 221.44 mm

Consider an RC beam cross section as shown below 300.mm 540 mm 50 mm 93. Determine the depth of the stress block a. 174.9 mm b. 147.9 mm 94. Determine the nominal moment capacity a. 411 kNm b. 445 kNm 95. Determine the depth of the neutral axis a. 121.54 mm b. 211.45 mm 96. Determine the nominal moment capacity As = 4,500mm² fy = 275 MPa f = 27 MPa c. 179.4 mm 197.4 mm d. c. 495 kNm d. 454 kNm c. 245.11 mm d. 221.44 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

4. Find the support reactions at A, B, C, and D. Assume E = 200GPa, and I = 1705 x10^6mm4. 32kN/m AA= 15mm AB= 36mm Ac 18mm. A 5m B 5m 5m D C
Q2: Analyze the frame and draw S.D and B.M? 10 kN/m 5 m El constant D 10 m
The rigid pipe BC shown is supported by a pin at C and an A- 36 guy wire AB (E = 200 GPa). The wire has a diameter of 8 mm. Determine the load P (kN) if the end B displaced 5.2 mm to the right. H = 3.5 m, 0 = 60°. A. 4.25 В. 6.30 C. 5.60 D. 3.23 H А
H.W. 2: Analyze the compound beam shown below with internal hinge at E and F. a. Check stability and determinacy of the beam. b. Draw the shear force and bending moment diagrams of the beam. 20 KN-m 3m x 13m x 2m hinge ,20 KN BITTE Fit. E hingef 5KN/m JOKN Andh I'm Im 2m 2m 2m 2m²: *
EXAMPLE 2.8 Draw the SFD and BMD for the beam shown below. 1000 N/m 3m 3m Solution; Calculate the support reactions. 5000N 3m 40000Nm | 3m 3m [Ans: V₁-8000 N (†), V₁-9000 N (1)] 4000N/m
Situation 11 An overhang beam is loaded as shown below. The beam cross-section was built by attaching two (2) channels to a 9mm thick plate using 16mm rivets The property of the channel is given: Determine the location of the maximum moment on the beam in meters. Determine the maximum moment, in kN-m, on the beam
HW 2 A cable is attached to the plate B of weight W, passes over a fixed peg at ingsand is attached to the block at A. U hown,sthe coefficients of static friction determine the smallest mass of block A so that it will prevent sliding motion of B .down the plane H 0.3 B 30
4. An overhanging beam AC carries a linearly varying load as shown below. Determine the position and the magnitude of the maximum positive bending moment. (Ans. Mmax 310Nm at x=2.12m from point A) A -1m- BA 1000N/m -2m- 5. Write the shear force and bending moment equations at any point of the simply supported beam shown below. Plot the corresponding diagrams.(Ans. Mmax-12000Nm) -12m- 1000N/m
For the frame shown, the distributed loading is applied at EFGH. All the vertical members (AE, IE, BF, JF etc.) have modulus of rigidity equal to El and 3m in length. Find (a) moment at MGH using Slope- Deflection Method. Input the magnitude only in kN-m. 12 kN 12 kN J | 12 kN 12 kN K 50 kN/m 20 kN/m 20 kN/m E ЗЕ 2EI 3EI H A В 6m 3m 3m 3m 3m 3m 3m
Analyze the continuous beam by the three-moment equation. Find the RA, R3 and Re 40 kN 20 kN/m A Sm 3m Зт
The shaft is supported by a smooth thrust bearing at A and a smooth journal bearing at B. Determine the resultant internal loadings acting on the cross section at C. 600 N/m A. В D |C |-1 m--1 m-1 m ---1.5 m1.5 m 900 N
Situation 2 | Beam ABCDEFG below is subjected to multiple loads as show. The total length of the beam is 10m. Analyze the beam completely. 6 kN 10 kN 3 kN/m 2 kN 5 kN-m G 3000mm. 1000mm 1000mm. 2000mm. 1000mm. 2000mm. 3. Determine the shear ation for segment B-C. ** 4. Determine the moment equation of segment C-D.**