Consider the 2-D state of stress shown below. Using the provided scales graph the Mohr's Circle for the 2-D state of stress with "full" details II-Obtain the Principal Stresses, the Maximum Shear Stress, and complete the table below III- Draw the Planes of Principal and Maximum Shear Stresses in the space provided below Provide "full" details and Use 3 Sig. Fig. in this problem Oy = 15 Ksi Tcw → S Ox = 10 Ksi TYx = 5 Ksi 10 5 -20 -15 -10 5 10 15 20 5 10 Tccw → S' O Avg. TMax. 01 02

Consider the 2-D state of stress shown below. Using the provided scales graph the Mohr's Circle for the 2-D state of stress with "full" details II-Obtain the Principal Stresses, the Maximum Shear Stress, and complete the table below III- Draw the Planes of Principal and Maximum Shear Stresses in the space provided below Provide "full" details and Use 3 Sig. Fig. in this problem Oy = 15 Ksi Tcw → S Ox = 10 Ksi TYx = 5 Ksi 10 5 -20 -15 -10 5 10 15 20 5 10 Tccw → S' O Avg. TMax. 01 02

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.7.19P: During a test of an airplane wing, the strain gage readings from a 45° rosette (see figure) are as...

See similar textbooks

Similar questions

The stresses acting on an element are x= 750 psi, y= 600 psi, and xy = 400 psi. Determine the principal stresses and show them on a sketch of a properly oriented element.
Consider the 2-D state of stress shown below. Using the provided scales graph the Mohr's Circle for the 2-D state of stress with "full' details Draw the Planes of Principal and Maximum Shear Stresses Provide "full" details and Use 3 Sig. Fig. in this problem Oy = 15 Ksi Tcw → S Txy= -5 ksi Ox = 10 Ksi Tyx = 5 Ksi 10 5 -20 -10 5 10 15 20 5 10 Tccw → S'
The state of stress at a point on an element of material is shown. Let sigmaX= 49.0 ksi, sigmaY= 17.0 ksi, and Txy= 11.0 ksi. Use this information to represent the principle state of stress and maximum in plane shear stress. Plot the mohr circle and state sigmaX' and sigmaY' and Tx'y' with unit. Also draw the state of stress on the rotated element.
1. Given a combination of stresses on an element shown in the figure, (a) draw a Mohr's circle representing the complete state of stress of the element, i.e. show prinicpal stresses (01,02), maximum shear stresses (Tmax), principal direction (0p), original orientation, and original stresses (Ox, Oy, Txy). (b) draw three-dimensional Mohr's circles showing the three principal stresses and absolute maximum shear stress. Oy = -50 MPa Txy 20 MPa Ox = -150 MPa
For each of the plane stress states listed below, draw a Mohr's circle diagram properly labeled, find the principal normal and shear stresses, and determine the angle from the r axis to of. Draw stress elements as in Figure 3-11c and d and label all details. a.) sigma,x = - 12 kpsi, sigma,y = 22 kpsi, txy = 12 kpsi cw b.) sigma,x = 30 kpsi, sigma,y = -10 kpsi, txy = 10 kpsi ccw c.) sigma,x = -10 kpsi, sigma,y = 18 kpsi, txy = 9 kpsi cw Attached is an image of Figure 3-11c and d for example. THIS IS THE ONLY INFORMATION I AM PROVIDED WITH! Thank you for the help in advance!
The stresses acting on element A in the web of a train rail are found to be 'X (MPa)' tension in the horizontal x-direction and 'Y (MPa)' compression in the vertical y-direction. Also, shear stresses of magnitude 'S (MPa)' act in the directions shown in the figure. Draw Mohr's circle for the state of stress. Determine the stresses (Ox', Oy' and Txy') acting on an element oriented at an angle 'D' from the horizontal Show these stresses on a sketch of an element oriented at this angle X=45MPA,Y=150MPA,S=52MPA,D=-40 Degree
Calcuate torsion From Point A to Point C, Calcuate Bending From Point A to Point B and Point A to Point C. Draw a FBD from point A to point B and another for point A to C indicating what stresses are been calculate. Use the stress tensor and stress cube to Indicate what forces are acting at point A. Force apply at point B is 70lb Distacen from Point A to B is 12 in or 1 feet long Distacen from Point A to C is 3 in Handle diameter 0.625 in
Angle 1 Tyx Tyx Figure 1 Point A- x-direction stress 60MPA(compression), y-direction stress 40MPA(tension), negative shear stress 30MPA Using your assigned point determine the following for the yz-plane: a) From basic priciples determine the stresses on the plane of the indicated angle 1-30°, Show al calculations. Draw the orientation of the stress block for this scenario. b) Repeat question (a) using a Mohr circle. c) Using a Mohr circle, determine and draw the maximum stress block of the in-plane maximum shear and principle stresses. d) Determine the stresses and orientation of the stress block where the normal stress is zero. Make use of the stress transformation equations. e) Determine the values of absolute maximum shear stress and corresponding normal stress.
Calcuate Bending From Point A to Point B and Point A to Point C, Calcuate torsion From Point A to Point C. Draw a FBD from point A to point B and another for point A to C indicating what stresses are been calculate. Use the stress tensor and stress cube to Indicate what forces are acting at point A. Force apply at point B is 70lb Distacen from Point A to B is 12 in or 1 feet long Distacen from Point A to C is 3 in Handle diameter 0.625 in
Problem 3: For the plane stress state listed below, draw a Mohr's circle diagram properly labeled. Keep in mind that the principal stress is that stress state where the shear stress is zero. That means it is the stress state along the normal stress line in Mohr's space. So, use your Mohr's circle to find the principal normal and shear stresses, and determine the angle from the x axis to o1. 0x = 16 kpsi, oy = 9 kpsi, Ty = 5 kpsi ccw
Consider the plane stress element shown in representing the state of stress at a material point. If the magnitudes of the stresses are such that ox 210 Pa, oy = 110 Pa, and = - Txy = 70 Pa, calculate the magnitudes of principal stresses oj and 02, and the maximum shear stress, Tmax, generated at %3D this material point. (a) Record here the the positive of the two principle stresses. (b) Record here the the negative of the two principle stresses. (c) Record here the the maximum shear stress. Tyz Oy
Q1. For the given cube below, complete the following: 1.find the center, radius (R), principal normal stresses (σ and σ3), max shear stress (Tmax) and draw the Mohr's Circle. 2. Find the stresses on a plane that is rotated 60° clockwise from the horizontal plane. 6PSE IPSF 10pst 60⁰ TOPST IPSF 6PSF