Consider the following function for 2-vector x = (x,x)“. Bold letter indicates vector f(x) = f(x ,.x) = x;'-xx;. a. Write the code to draw a 3D plot for the function f(x) in MATLAB for x, = 1:500 and x, = 1:500. So the plot will have 3 axis: x, x, and f(x) in first subplot b. Now the taylor first order approximation of f(x) is: f_ hat(x) = 3x1 - 2x2. Write the code to 3D plot the function f_hat(x) for x, subplot 1:500 and x, = 1:500 in 2nd

Consider the following function for 2-vector x = (x,x)“. Bold letter indicates vector f(x) = f(x ,.x) = x;'-xx;. a. Write the code to draw a 3D plot for the function f(x) in MATLAB for x, = 1:500 and x, = 1:500. So the plot will have 3 axis: x, x, and f(x) in first subplot b. Now the taylor first order approximation of f(x) is: f_ hat(x) = 3x1 - 2x2. Write the code to 3D plot the function f_hat(x) for x, subplot 1:500 and x, = 1:500 in 2nd

Database System Concepts

7th Edition

ISBN:9780078022159

Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Chapter1: Introduction

Section: Chapter Questions

Problem 1PE

See similar textbooks

Similar questions

Although the plot function is designed primarily for plotting standard xy graphs, it can be adapted for other kinds of plotting as well. b. Make a plot of the curve, which is defined parametrically by the equations x = 2cosθ + cos2θ, y = 2sinθ - sin2θ, where 0 < θ < 2π. Take a set of values of θ between zero and 2π and calculate x and y for each from the equations above, then plot y as a function of x. b. Taking this approach a step further, one can make a polar plot r = f(θ) for some function f by calculating r for a range of values of θ and then converting r and θ to Cartesian coordinates using the standard equations x = r cosθ, y = r sinθ. Use this method to make a plot of the function r = ecosθ – 2 cos(4θ) + sin5 (θ/12) in the range 0 <= θ <= 24π. use python code to answer the highlight one
Can you help me program this in MATLAB? Transformation from Keplerian orbital elements to cartesian coordinates. Write a function script in the form (x,y,z,vx,vy,vz) = orb2cart(a,ecc,inc,raan,argp,f). This is going from Keplerian orbital elements to the cartesian coordinates. Inputing state vector (x,y,z,vx,vy,vz) to get orbital elements (a,ecc,inc,raan,argp,f).
The compass gradient operators of size 3x3 are designed to measure gradients of edges oriented in eight directions: E, NE, N, NW, W, SW, S, and SE. i) Give the form of these eight operators using coefficients valued 0, 1 or – 1. ii) Specify the gradient vector direction of each mask, keeping in mind that the gradient direction is orthogonal to the edge direction.
In Matlab We are going to calculate the average to these datapoints (the measurements is a vector with arbitrary real number xmean =(sum of measurements xi )/ (number of measurements, N) and the standard deviation std= sqrt. ((∑(xi - xmean)2 / (N-1)) create a user defined function that takes the vector with the data points as input-arguments and produces the average and standard deviation as output variables.
Write a user-defined MatLab function I=Simp38(FunName,a,b) using the composite Simpson's 3/8 method. FunName is a handle function that calculates the value of the function to be integrated, a and b are the limits of integration and I is the value of the integral. The function should calculate the value of the integral in iterations. In the first iteration the interval [a,b] is divided in two subintervals and in every iterations that follows the number of subintervals should be doubled. Stop the iterations when the difference in the value between two successive iterations is smaller than 1%.
Write a function to determine the resultant force vector R of the two forces F₁ and F2 applied to the bracket, where 0₁ and 02. Write R in terms of unit vector along the x and y axis. R must be a vector, for example R = [Rx, Ry]. The coordinate system is shown in the figure below: F₁ y 0₂ 0₁ F2
Assignment: Create a surface and contour plot of function z=f(x,y) [-5,5] by [-5,51. Take a pick to plot from any of the choices below. (01) f(x,y) = x*y**3-y*x**3 (02) f(x,y) = (x**2+3*y**2) *exp(-x**2-y**2) (03) f(x, y) = -1/(x**2+y**2) (04) f(x, y) = cos(abs(x)+abs(y)) - Use at least 500 points in each direction to discretize domain and create the grid. - Make the surface plot red and without grid lines. - For contour plot, specify contour levels to go from minimum and maximum Z values on the entire domain and include at least 15 contour levels. - Pick a colormap you like I ## Create data import numpy as np import pyvista as pv
What role does the reflection vector play in computer graphics? The following should have at least two examples of each.
Consider the parabola defined by y = x^2 − 2x − 4. The distance d(x) from the origin (0, 0) to a point (x, y) on the parabola is d(x) = √x^2 + (x^2 − 2x − 4)^2 (a) Write a MATLAB program and function M-file to plot d(x) for −2 ≤ x ≤ 4, and use the fminbnd command to find the point (x and y coordinates) on the parabola that is closest to the origin and the minimum distance. (b) Write a MATLAB program using the fzero command to find the point(s) on the parabola at a distance of 3 from the origin.
Create a MATLAB function that selects a random element from a list of values in a vector. Using the built-in function 'randi'. Example: For input options = [3, 2, 5], the output for this function should be able to choose one of the three numbers, with an equal chance of choosing each (20% chance each). chosen_value = select_random_option([3, 2, 5]) value = 3 chosen_value = select_random_option([3, 2, 5]) value = 5 chosen_value = select_random_option([3, 2, 5]) value = 2
What is the function of the reflection vector in computer graphics? Each of the following should have at least two examples.
In Matlab code 2. A fibonacci sequence is a sequence such that, beginning with the third element, each term is the sum of the two previous ones. For a particular fibonacci sequence a₁ = 3 and a₂ = 7. Use a for loop to (i) generate the first 50 terms of the sequence. Store the sequence values in a vector. (ii) generate a sequence of ratios of the successive terms. For example, the first element will be 7/3, the second element will be 10/7.